Search Results

Abstract This article reports a reduced-order modeling framework of bladed disks on a rotating shaft to simulate the vibration signature of faults in different components, aiming toward simulated data-driven machine learning. We have employed lumped and one-dimensional analytical models of the subcomponents for better insight into the complex dynamic response. The framework addresses some of the challenges encountered in analyzing and optimizing fault detection and identification schemes for health monitoring of aeroengines and other rotating machinery. We model the bladed disks and shafts by combining lumped elements and one-dimensional finite elements, leading to a coupled system. The simulation results are in good agreement with previously published data. We model and analyze the cracks in a blade with their effective reduced stiffness approximation.

Abstract To ensure the ongoing safety of aircraft, it is necessary to conduct risk assessment for those events that occurred during routine operations. Consequently, the corresponding corrective actions should be accomplished within the compliance time if the event was ascertained to be unsafe. However, the existing models of risk assessment and determination of the correction time limit have not dealt with the time-varying failure rate of components. Based on the Gunstone method, this article considers the event risks of the fleet at different correction time limits, combined with the Monte Carlo method to establish a model of risk assessment and determination of the correction time limit. Based on the event risk level and the risk per flight hour, the risks of the event under the condition of no corrective actions and corrective actions with different time limits were assessed, respectively.

Abstract Piston internal combustion engines used in the propulsion of ultralight aircraft are characterized by special operating conditions, especially an increased engine oil temperature. Most of the engines intended for the drive of the propeller drivetrain are air cooled. Failure to introduce an additional cooling agent so as to absorb and remove heat from the running engine makes the average lubricating oil temperature rise to about 140°C in the pistohn ring part. With such a thermal load, changes in the moments of resistance to motion of the engine are difficult to determine in the conditions of engine tests due to difficulties in temperature stabilization. The performance of aircraft engines requires taking into account many variables that are difficult to determine, which may affect changes in the moment of resistance to movement of the engine, especially when using oils of low dynamic viscosity.

Abstract Jet engine hot parts (e.g., jet nozzle) are a crucial source of aircraft’s infrared (IR) signature from the rearview, in 1.9-2.9 μm and 3-5 μm bands. The exhaust nozzle design used in a jet aircraft affects its performance and IR signature (which is also affected just by performance) from the engine layout. For supersonic aircraft (typically for M ∞ > 1.5), a converging-diverging (C-D) nozzle is preferred over a convergent nozzle for optimum performance. The diverging section of the C-D nozzle has a full range of visibility from the rearview; hence, it was not considered a prudent choice for low IR observability. This theoretical study compares the IR signature of the C-D nozzle with that of the convergent nozzle from the rearview in 1.9-2.9 μm and 3-5 μm bands for the same thrust.

Abstract The turboshaft engine performance is closely related to the helicopter’s design, and because of its location beneath the helicopter’s main rotor, it has unique features that distinguish it from other families of gas turbine engines. The impact of the engine suction and main rotor’s blow in different flight regimes and climatic conditions lead to variations in speed, pressure, and temperature at the inlet of the turboshaft engines, which, in turn, will affect the design of the engine cycle. Therefore, in this article, the equations governing the airflow for turboshaft engines are enhanced to incorporate these effects. The equations in this article are derived using aerodynamics, flight dynamics, helicopter, and turboshaft design to lend the inlet velocity of the engine. In order to validate the analytical outcomes of these equations, a computational fluid dynamics (CFD) analysis is carried out to evaluate the turbulent flow at the T700-GE turboshaft inlet.

Abstract Possible oil contamination of aircraft bleed air is an ongoing operational issue for commercial aircraft. A sensitive and reliable method to detect contamination, especially at very low levels, has been elusive due, in part, to the lack of information about the physical nature of oil that results when entrained in the bleed air by an engine compressor. While it was expected that high shear rates in the compressors would result in very finely dispersed particles, detailed data on the size characteristics of these droplets were not available, making it difficult to develop reliable detection techniques. The goal of the reported research was to collect experimental data to provide this information. The concentration and size distribution of particles were measured for bleed air with different rates of controlled oil contamination under various engine operating conditions.

Abstract Inline piston pumps are extensively used in aircraft hydraulic systems. They can be found in engine-driven large-sized hydraulic pumps and zonal electric motor-driven mid-small sized pumps. Inline piston pumps are positive displacement pumps with variable volumetric flow controls. Positive displacement pumps can provide a variable flow rate over a wide range of suction pressures. Aircraft fly at high altitudes, and therefore these pumps have to work in extreme conditions such as low atmospheric pressure, low temperature. At low inlet pressures, the pump is highly susceptible to cavitation, i.e., insufficient filling capacity. The pressure below which pump flow rate drops drastically is known as critical inlet pressure. Extensive research has been carried out to study cavitation in inline piston pumps.

Abstract For electromechanical actuators (EMAs) and electronic devices cooling on aircraft, there is a need to study cooling fan performance at various altitudes from sea level to 12,000 m where the ambient pressure varies from 1 to 0.2 atm. As fan static pressure head is proportional to air density, the fan’s rotational speed has to be increased significantly to compensate for the low ambient pressure of 0.2 atm at the altitude of 12,000 m. To evaluate fan performance for EMA cooling, a high-rotational-speed, commercially available fan made by Ametek with a diameter of ~82 mm and ~3 m3/min zero-load open cooling flow rate when operating at 20,000 rpm was chosen as the baseline. According to fan scaling laws, this fan was expected to meet the cooling needs for an EMA when operating at 0.2 atm. Using a closed flow loop, the performance of the fan operating in the above ambient pressure range and at a rotational speed between 15,000 and 30,000 rpm was evaluated.

Abstract For spacecraft with high power consumption, it is reasonable to build the thermal control system based on a two-phase mechanically pumped loop. The heat-controlled accumulator is a key element of the two-phase mechanically pumped loop, which allows for the control of pressure in the loop and maintains the required level of coolant boiling temperature or cavitation margin at the pump inlet. There can be two critical modes of loop operation where the ability to control pressure will be lost. The first critical mode occurs when the accumulator fills with liquid at high heat loads. The second critical mode occurs when the accumulator is at low heat loads and partial loss of coolant, for example, due to the leak caused by micrometeorite breakdown. Both modes are caused by insufficient accumulator volume or working fluid charge.

Abstract Turboshaft engines, one of the classifications of the helicopters, combine the core engine and fan and consume fossil fuels. Using of fossil fuel causes global warming and environmental pollution, such as ecological, human health. To improve helicopter capability, energy is the first point of improvement. High-energy efficient helicopter engines help decrease the environmental damage. Exergy should be applied to the system to determine the maximum available energy. In this study, energy analysis and exergy analysis have been applied to a turboshaft helicopter engine. According to the result of this study, the maximum energy and exergy efficiencies are found to be 21.99% and 15.87%, respectively, at 1500 Shaft Horsepower (SHP). It is seen that the efficiencies increase with the increase of the engine power. Besides, exergy destructions and exergy loss values are presented by calculating different powers.

Abstract Electrostatic discharge during aircraft refueling operations has long been recognized as a safety hazard. To reduce the chances of this happening, different practices were developed, the most common being the addition of a static dissipator additive (SDA). Nowadays, the SDA is a well-established requirement in all the leading jet-fuel specifications and is in widespread use in commercial and military aviation industries. To deepen the understanding of the electrostatic behavior of nonconductive jet fuel and SDA, the Israeli Air Force (IAF) has conducted small-scale refueling tests in a simulated aircraft fuel tank. In these tests, the effect of flow rate, residence time, SDA concentration, bounding, grounding, and the method of filling were evaluated by measuring the electrostatic field strength generated. The simulation of the aircraft fuel tank was obtained using a nonconductive plastic tank jointed with a small faucet at the bottom.

Abstract Emissions and effects of climate change have prompted study into fuels that reduce global dependence on traditional fuels. This study seeks to investigate engine performance, thermochemical properties, emissions, and perform NVH analysis of Jet-A and S8 using a single-stage turbojet engine at three engine speeds. Experimental Jet-A results were used to validate a CFX simulation of the engine. Engine performance was quantified using thermocouples, pressure sensors, tachometers, flow meters, and load cells fitted to the engine. Emissions results were collected using an MKS Multigas Emissions Analyzer that examined CO, CO₂, H₂O, NOx, and THC. NVH analysis was conducted using a multifield, free-field microphone, and triaxial accelerometer. This study found that Jet-A operates at higher temperatures and pressures than S8, and S8 requires higher fuel flow rates than Jet-A, leading to poorer efficiency and thrust. S8 produced stronger vibrations over 5 kHz compared to Jet-A.

Abstract In the aeronautical field, aircraft reliability is strictly dependent on propulsion systems. Indeed, a reliable propulsion system ensures the safety of pilots and passengers and the possibility of making comfortable flights. Typically, on aircraft equipped with spark ignition (SI) engines, one of the principal requirements to make them reliable is the correct balancing between the intake air mass and fuel flows. Advances in the implementation of sophisticated control and estimation strategies on SI engines allow realizing engines with improved features in terms of performance, reducing pollution emissions, and fuel consumption. Approaches based on sensor redundancy are applied to improve the reliability in measurements of the manifold air pressure (MAP) and flow (MAF) to avoid issues related to possible faults of sensors vital for the correct functioning of SI engines.

Abstract Significant attention has been focused on Mars due to its relative proximity and possibility of sustaining human life. However, its lack of in-situ sources of energy presents a challenge to generate needed energy on the surface. Comparatively, Titan has a nearly endless source of fuel in its atmosphere and lakes, but both are lacking in regards to their oxidizing capacity. The finding of a possible underground liquid ammonia-water lake on Titan suggests that oxygen might actually be within reach. This effort provides the first theoretical study involving a primary energy generation system on Titan using the atmosphere as a fuel and underground water as the source for the oxygen via electrolysis from wind generated electricity.

Abstract Many interconnected parameters are involved in the helicopter turboshaft engine’s design, implying numerous limitations on the design process. These parameters include the key parameters such as weight, dimensions, power, specific fuel consumption, combustion temperature, air mass flow rate, and compressor pressure ratio, all of which correlate with one another and collectively affect the engine’s design process and consequently the helicopter. The first step in any design process is the conceptual design stage, where using an initial guess, an iterative parameter estimation runs until convergence. For the initial guess, a database is required, and for estimation, knowledge of the relationships between different parameters is mandatory.

Abstract More than a decade ago, we proposed combined use of direct injection (DI) and jet ignition (JI) to produce high efficiency, high power-density, positive-ignition (PI), lean burn stratified, internal combustion engines (ICEs). Adopting this concept, the latest FIA F1 engines, which are electrically assisted, turbocharged, directly injected, jet ignited, gasoline engines and work lean stratified in a highly boosted environment, have delivered peak power fuel conversion efficiencies well above 46%, with specific power densities more than 340 kW/liter. The concept, further evolved, is here presented for unmanned aerial vehicle (UAV) applications. Results of simulations for a new DI JI ICE with rotary valve, being super-turbocharged and having gasoline or methanol as working fuel, show the opportunity to achieve even larger power densities, up to 430 kW/liter, while delivering a near-constant torque and, consequently, a nearly linear power curve over a wide range of speeds.

Abstract Phosphate ester-based hydraulic fluids are commonly used in aviation, due to their fire-resistant properties. However, contamination of jet fuel with hydraulic fluid may cause serious engine failure, hot corrosion of metals, and swelling of elastomer and polymer seals. Identifying and quantifying hydraulic fluids in jet fuels using chromatography is challenging since common hydraulic fluids, such as ExxonMobil™ HyJet™ V and Skydrol™ LD-4, are composed of tri-butyl phosphate, the main peak of which overlaps with peaks from jet fuels in chromatograms. In this work, three techniques to separate and differentiate the jet fuel peaks from the tri-butyl phosphate peaks were developed. Two methods are based on a solid phase extraction (SPE) procedure followed by identification and quantification, which is carried out using a gas chromatograph equipped with a mass spectrometer or a flame ionization detector.

Abstract A large amount of heat generated in the engineering compartment in a hovering helicopter may lead to premature degradation of inner skin of its engine cowling and cause serious failure on the engine cowling. This study proposes a solution of improving heat resistance of the helicopter engine cowlings by replacing the currently used intumescent coating with a ceramic coating material, Cerakote C-7700Q. Oven and flame tests were designed and conducted to evaluate the heat resistance of Cerakote C-7700Q. The test results show that the currently used painting scheme of the engine cowlings failed the 220°C oven test while after replacing the epoxy seal coat with the Cerakote, the new painting system passed the 220°C test in regards to painting bubbling. Based on that, a new painting scheme with C-7700Q implemented was recommended.

Abstract The use of converging-diverging (C-D) variable area nozzle (VAN) in military aeroengines is now common, as it can give optimal expansion and control over engine back pressure, for a wide range of engine operations. At higher main combustion temperatures (desired for supercruise), an increase in the nozzle expansion ratio is needed for optimum performance. But changes in the nozzle throat and exit areas affect the visibility of engine hot parts as the diverging section of the nozzle is visible for a full range of view angle from the rear aspect. The solid angle subtended by engine hot parts varies with change in visibility, which affects the aircraft infrared (IR) signature from the rear aspect. This study compares the performances of fixed and variable area nozzles (FAN and VAN) in terms of engine thrust and IR signature of the engine exhaust system in the boresight for the same increase in combustion temperature.

Abstract This work describes an investigation of measurement techniques for the indicated mean effective pressure (IMEP) on a 55 cc single-cylinder, 4.4 kW, two-stroke, spark ignition (SI) engine intended for use on Group 1 and Group 2 remotely piloted aircraft (RPAs). Three different sensors were used: two piezoelectric pressure transducers (one flush mount and one measuring spark plug) for measuring in-cylinder pressure and one capacitive sensor for determining the top dead center (TDC) position of the piston. The effort consisted of three objectives: to investigate the merits of a flush mount pressure transducer compared to a pressure transducer integrated into the spark plug, to perform a parametric analysis to characterize the effect of the variability in the engine test bench controls on the IMEP, and to determine the thermodynamic loss angle for the engine.