Search Results

A 10 KWe dual-mode space power system concept has been identified which is based on INEL's Small Externally-fueled Heat Pipe Thermionic Reactor (SEHPTR) concept. This power system will enhance user capabilities by providing reliable electric power and by providing two propulsion systems; electric power for an arc-jet electric propulsion system and direct thrust by heating hydrogen propellant inside the reactor. The low thrust electric thrusters allow efficient station keeping and long-term maneuvering. The direct thrust capability can provide tens of pounds of thrust at a specific impulse of around 730 seconds for maneuvers that must be performed more rapidly. The direct thrust allows the nuclear power system to move a payload from Low Earth Orbit (LEO) to Geosynchronous Earth Orbit (GEO) in less than one month using approximately half the propellant of a cryogenic chemical stage.

Most of current jet aircraft circulate fuel on the airframe to match heat loads with available heat sink. The demands for thermal management in wide range of air vehicle systems are growing rapidly along with the increased mission power, vehicle survivability, flight speeds, and so on. With improved aircraft performance and growth of heat load created by Aircraft Mounted Accessory Drive (AMAD) system and hydraulic system, effectively removing the large amount of heat load on the aircraft is gaining crucial importance. Fuel is becoming heat transfer fluid of choice for aircraft thermal management since it offers improved heat transfer characteristics and offers fewer system penalties than air. In the scope of this paper, an AMESim model is built which includes airframe fuel and hydraulic systems with AMAD gearbox of a jet trainer aircraft. The integrated model will be evaluated for thermal performance.

A 500 hours endurance test was performed with a heavy-duty engine (Euro IV); MAN type D 0836 LFL 51 equipped with a PM-Kat®. As fuel 100% biodiesel was used that met the European specification EN 14214. The 500 hours endurance test included both the European stationary and transient cycle (ESC and ETC) as well as longer stationary phases. During the test, regulated emissions (carbon monoxide, nitrogen oxides, hydrocarbons and particulate matter), the particle number distribution and the aldehydes emission were continuously measured. For comparison, tests with fossil diesel fuel were performed before and after the endurance test. During the endurance test, the engine was failure-free for 500 hours with the biogenic fuel. There were almost no differences in specific fuel consumption during the test, but the average exhaust gas temperature increased by about 15°C over the time. Emissions changed only slightly during the test.

Offering aircraft fuel efficiency improvements of 30 to 40% over the powerplants it will replace, PW2037 retrofit in the 727-200 Advanced and B-52 aircraft is attracting heightened interest. A comparison of PW2037 technical characteristics with current aircraft powerplants substantiates the improvement potential.The engine installation and modifications necessary for aircraft system compatibility do not impose significant increases in complexity or cost. The resultant improvements in aircraft capability (727 and B-52) and economic viability to airlines (7271 produce aircraft uniquely suited to today's operational requirements and constrained equipment budgets.

The 912 engine is a well known 4-cylinder horizontally opposed 4-stroke liquid-/air-cooled aircraft engine. The 912 family has a strong track record: 40 000 engines sold / 25 000 still in operation / 5 million flight hours annually. 88% of all light aircraft OEMs use Rotax engines. The 912iS is an evolution of the Rotax 912ULS carbureted engine. The “i” stands for electronic fuel injection which has been developed according to flight standards, providing a better fuel efficiency over the current 912ULS of more than 20% and in a range of 38% to 70% compared to other competitive engines in the light sport, ultra-light aircraft and the general aviation industry. BRP engineers have incorporated several technology enhancements. The fully redundant digital Engine Control Unit (ECU) offers a computer based electronic diagnostic system which makes it easier to diagnose and service the engine.

This paper discusses various engine installations in Naval aircraft, looking especially at their costs of maintenance. Fuel systems, fuel control systems, and several engine accessories are discussed for present and future engines. It is concluded that simple, reliable equipment is necessary to keep aircraft in the air instead of in maintenance areas on the ground.

A short survey of wing tip geometries for drag reduction is presented. These devices have been divided into two broad categories of passive and active. The first category is made of fixed geometries, while the second group is made of those employing moving parts. The former group is further divided into planar and nonplanar designs. In every case, a brief explanation of the underlying logic is given. Altogether, more than fifteen completely different designs and over seventy references have been cited. Some of these designs, such as winglets, have been explored for many years and have proven to be very effective at reducing the induced drag at higher values of lift coefficient. Some others, such as wing tip turbines, have just begun to attract attention. Wing tip fuel tanks, not being solely employed for drag reduction, have not been included in this paper.

A series calculation methodology from the injector nozzle internal flow to the fuel spray was applied to investigate the internal flow and spray of a nozzle whose orifices distributed in different space layers. The nozzle internal flow calculation using an Eulerian three-fluid model and a cavitation model was performed. The needle valve movement during the injection period was taken into account in this calculation. The transient data of spatial distributions of velocity, turbulent kinetic energy, dissipation rate, void fraction rate, etc. at the nozzle exit were extracted. These output data were transferred to the spray calculation, in which a primary break-up model was applied to the Discrete Droplet Model (DDM). The calculation results were compared with the results of the measurement data of spray. Predicted spray morphology and penetration showed good agreement with the experiental data.

A new family of canister-type fuel pumps for use on both rotary and fixed-wing aircraft in general aviation use will be described. The pump, which features a wet-brush DC motor, offers advantages on aircraft where ease of maintenance and minimum downtime is very important. Major features of the new design, pump performance, and maintenance cost savings will be discussed.

A hydrogen economy is an increasingly popular solution to lower global carbon dioxide emissions. Previous research has been focused on the economic conditions necessary for hydrogen to be cost competitive, which tends to neglect the effectiveness of greenhouse gas mitigation for the very solutions proposed. The holistic carbon footprint assessment of hydrogen production, distribution, and utilization methods, otherwise known as “well-to-wheels” carbon intensity, is critical to ensure the new hydrogen strategies proposed are effective in reducing global carbon emissions. When looking at these total carbon intensities, however, there is no single clear consensus regarding the pathway forward. When comparing the two fundamental technologies of steam methane reforming and electrolysis, there are different scenarios where either technology has a “greener” outcome.

This paper documents the design and validation of a closed cycle propulsion system suitable for use on the Perseus A high altitude research aircraft. The atmospheric science community is expected to be the primary user of this aircraft with initial missions devoted to the study of ozone depletion and global warming. To date large amounts of funding are not available to the atmospheric science community, so to be useful, the aircraft must satisfy stringent cost and performance criteria. Among these, the aircraft has to be capable of carrying 50 kg of payload to altitudes of at least 25km, have a initial cost in the $1-2M range, be capable of launch from remote sites, and be available no later than 1994. These operational criteria set narrow boundaries for propulsion system cost, complexity, availability, reliability, and logistical support requirements.

As mission length and the number and complexity of payload experiments increase, so does the probability of thermodegradation contingencies (e.g. fire, chemical release and/or smoke from overheated components or burning materials), which could affect mission success. When a thermodegradation event occurs on board a spacecraft, potentially hazardous levels of toxic gases could be released into the internal atmosphere. Experiences on board the Space Shuttle have clearly demonstrated the possibility of small thermodegradation events occurring during even relatively short missions. This paper will describe the Combustion Products Analyzer (CPA), which is being developed under the direction of the Toxicology Laboratory at Johnson Space Center to provide necessary data on air quality in the Shuttle following a thermodegradation incident.

Eight fixed-wing reusable horizontal landing booster point design concepts are presented and compared on the basis of weight, cost, technical difficulty, and availability date. The eight vehicle types considered are all basically two-stage systems with a lifting body reusable second stage, with all vehicles normalized to place 40,000 lbs. payload in orbit. All flight vehicles are fully recoverable and capable of flying back and landing at the launch site. Vehicle types discussed are vertical take-off horizontal landing rockets, sled launched horizontal take-off rockets, runway launched horizontal take-off rockets, air breathing first stages, combined air breathing and rocket first stages, oxidizer collection concepts, supersonic combustion ramjets, and in-flight refueling vehicles. Each of these vehicle types is depicted in the paper and its design and performance characteristics are discussed.

In recent years, a tremendous interest has spawned towards adapting Lithium-Ion battery technology for aircraft applications. Lithium-Ion technology is already being used in some military aircraft (e.g., the F-22, F-35 and the B-2) and it has also been selected as original equipment for large commercial aircraft (e.g., the Airbus A380 and Boeing B787). The advantages of Lithium-Ion technology over Lead-Acid and Nickel-Cadmium technologies are higher specific energy (Wh/kg) and energy density (Wh/L), and longer cycle life. Saving weight is especially important in aircraft applications, because it can boost fuel economy and increase mission capability. Disadvantages of Lithium-Ion technology include higher initial cost, limited calendar/float life, inferior low temperature performance, and more severe safety hazards. This paper will present a direct comparison of a 24-Volt, 28Ah Lead-Acid and a 24-volt, 28Ah Lithium-Ion aircraft battery.

A comparison was done of the prediction capabilities for lightning indirect effects of two two-dimensional (2-D) computer codes using two graphite structural test fixtures. The two codes evaluated were an internal Boeing Method-of-Moments code and a commercially available Boundary Element method code. The codes were compared against each other and against test data. The purpose was to evaluate the prediction capabilities of both codes for use in predicting lightning indirect effects on internal components of graphite structure. Since 2-D codes are much easier to use than 3-D codes, they could be widely used in trade studies and design evaluations for lightning indirect effects protection of composite aircraft. The first code, REDIST, is a Method-of-Moments code developed in the 1980’s for use on the B-2. The REDIST code has short run times and is somewhat easier to use than the second code that was investigated.

Both humans and onboard radiosensitive systems (electronics, materials, payloads and experiments) are exposed to the deleterious effects of the harsh space radiations found in the space environment. The purpose of this paper is to present the space radiation environment extended to deep space based on environment models for the moon, Mars, Jupiter, and Saturn and compare these radiation environments with the earth's radiation environment, which is used as a comparative baseline. The space radiation environment consists of high-energy protons and electrons that are magnetically “trapped” in planetary bodies that have an intrinsic magnetic field; this is the case for earth, Jupiter, and Saturn (the moon and Mars do not have a magnetic field). For the earth this region is called the “Van Allen belts,” and models of both the trapped protons (AP-8 model) and electrons (AE-8 model) have been developed.

Fuel gaging systems in over 90% of small civil aircraft use the automotive float type sender with an electrical indicator. Considering such factors as dihedral, summing, temperature, variation in specific gravity of fuel used, and input voltage, the accuracy is approximately ±5% of full scale and ±10% of the reading. A more accurate system is highly desirable for weight control, flight planning, and possible c. g. consideration. Among other gaging systems available are improved float types at moderate costs, capacitive systems with good accuracy at comparatively high initial cost and increased maintenance, and a mass sensing system at moderate cost. The pros and cons of each system are discussed. Factors contributing to errors in readout and often overlooked are variations in height versus volume of fuel tanks because of manufacturing tolerances, and changes in shape and relative position of tanks under different loading when in flight.

Considering the rising cost and diminished availability of 100-octane, low-lead (100 LL) aviation gasoline, owners of aircraft certified for 100 LL may be forced to find an alternative fuel in the near future. This study proposed a blend of 200-proof anhydrous ethanol ($1.70 per gallon) and automotive gasoline ($1.15 per gallon) as a replacement for aviation gasoline ($1.90 per gallon). The research program included materials compatibility tests, Cooperative Fuel Research (CFR) engine tests, static thrust tests, and a flight test to determine the feasibility of such a blend as a fuel for an unmodified aircraft engine. Throughout all tests, blends burned as well as aviation gasoline. The static thrust tests indicated that a blend of 35% ethanol/65% automotive gasoline yielded the maximum thrust output. The materials tests revealed metals to be unaffected by contact with the blend fuel. Fibrous growths were discovered in the blend and in the automotive gasoline samples.

The BSTCA (Battery Section Thermal Control Assembly) is a module of the Columbus MTFF (Man Tended Free Flyer). Electrical power required during eclipse periods, is made available from six nickel hydrogen batteries. A sophisticated multi-radiator configuration, with a hybrid heat pipe network, has evolved. Autonomous control of the assembly heat rejection capability has been achieved by a integrated network of LTHP's (Liquid Trap Heat Pipes) and CCHP's (Constant Conductance Heat Pipes) under the control of a conventional HCU (Heater Control Unit). The process of design selection and verification is discussed, for the BSTCA, with a detailed LTHP component presentation.

A general discussion of the problems resulting from the introduction of contaminated jet turbine fuel into integral fuel tanks and a five-point program designed to eliminate the contamination problem are presented. Some areas covered are: inspection of fuel sources for contamination to prevent contaminants from entering the aircraft fuel system; decontamination of fuel sources; inspection and decontamination of the aircraft fuel system; use of additives for the control of microorganisms; materials and methods, including a simple system for introducing the additives. The good and bad points of all fuel tank sealing and finishing systems presently in use are discussed, and a new finish system completely resistant to degradation by microorganisms is introduced. Simple means of controlling fuel quality entering the aircraft from uncontrolled sources are outlined.