Search Results

This SAE Aerospace Standard (AS) contains requirements for a digital time division command/response multiplex data bus, for use in systems integration that is functionally similar to MIL-STD-1553B with Notice 2 but with a star topology and some deleted functionality. Even with the use of this document, differences may exist between multiplex data buses in different system applications due to particular application requirements and the options allowed in this document. The system designer must recognize this fact and design the multiplex bus controller (BC) hardware and software to accommodate such differences. These designer selected options must exist to allow the necessary flexibility in the design of specific multiplex systems in order to provide for the control mechanism, architectural redundancy, degradation concept, and traffic patterns peculiar to the specific application requirements.

Most of current jet aircraft circulate fuel on the airframe to match heat loads with available heat sink. The demands for thermal management in wide range of air vehicle systems are growing rapidly along with the increased mission power, vehicle survivability, flight speeds, and so on. With improved aircraft performance and growth of heat load created by Aircraft Mounted Accessory Drive (AMAD) system and hydraulic system, effectively removing the large amount of heat load on the aircraft is gaining crucial importance. Fuel is becoming heat transfer fluid of choice for aircraft thermal management since it offers improved heat transfer characteristics and offers fewer system penalties than air. In the scope of this paper, an AMESim model is built which includes airframe fuel and hydraulic systems with AMAD gearbox of a jet trainer aircraft. The integrated model will be evaluated for thermal performance.

The term “3 inch ice shapes” has assumed numerous definitions throughout the years. At times it has been used to generally characterize large glaze ice accretions on the major aerodynamic surfaces (wing, horizontal stabilizer, vertical stabilizer) for evaluating aerodynamic performance and handling qualities after a prolonged icing encounter. It has also been used as a more direct criterion while determining or enforcing sectional ice shape characteristics such as the maximum pinnacle height. It is the authors’ observation that over the years, the interpretation and application of this term has evolved and is now broadly misunderstood. Compounding the situation is, at present, a seemingly contradictory set of guidance among (and even within) the various international regulatory agencies resulting in an ambiguous set of expectations for design and certification specialists.

This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.

This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.

Unguided sounding rockets, also known as sub-orbital rockets, are vehicles that carry scientific experiments and/or sensors to collect data during their trajectory. These rockets lack active control but are capable of traversing the Earth’s atmosphere. It is crucial to thoroughly analyze the flight parameters during the preliminary design phase. The Open Rocket flight simulation software, developed by Sampo Niskanen, is a widely used open-source project. However, it has some simplifications in comparison to its documentation. It does not specify the calculations of critical parameters required for the rocket’s stability during its flight. Additionally, it does not calculate data related to dynamic stability, which encompasses the system’s ability to make disturbances corrections during the rocket’s trajectory. Consequently, this study presents a flight simulation of a rocket with 6 degrees of freedom using Matlab/Simulink.

The 747 flight test certification program was initiated with the first flight of the No. 1 airplane on February 9, 1969. Five test airplanes were used in an intensive test program involving 1443 flight hr and 36-1/4 airplane months, with the last certification flight on December 23, 1969. Full type certification approval was granted by the FAA on December 30, 1969 after a total of 10-2/3 months of flight testing. These statistics compare very well with the original program estimates, which were based on Boeing's extensive experience with development and certification testing of commercial transport airplanes. The success of this test program was not due to any great advancements in flight test techniques specifically for the 747, but was due to the tried and proven test methods developed during past certification programs at Boeing. This is not meant to imply that some new methods were not used, but to emphasize that test techniques evolve with experience.

The 912 engine is a well known 4-cylinder horizontally opposed 4-stroke liquid-/air-cooled aircraft engine. The 912 family has a strong track record: 40 000 engines sold / 25 000 still in operation / 5 million flight hours annually. 88% of all light aircraft OEMs use Rotax engines. The 912iS is an evolution of the Rotax 912ULS carbureted engine. The “i” stands for electronic fuel injection which has been developed according to flight standards, providing a better fuel efficiency over the current 912ULS of more than 20% and in a range of 38% to 70% compared to other competitive engines in the light sport, ultra-light aircraft and the general aviation industry. BRP engineers have incorporated several technology enhancements. The fully redundant digital Engine Control Unit (ECU) offers a computer based electronic diagnostic system which makes it easier to diagnose and service the engine.

A low pressure axial fan for benchmarking numerical methods in the field of aerodynamics and aeroacoustics is presented. The generic fan for this benchmark is a typical fan to be used in commercial applications. The design procedure was according to the blade element theory for low solidity fans. A wide range of experimental data is available, including aerodynamic performance of the fan (fan characteristic curve), fluid mechanical quantities on the pressure and suction side from laser Doppler anemometer (LDA) measurements, wall pressure fluctuations in the gap region and sound characteristics on the suction side from sound power and microphone array measurements. The experimental setups are described in detail, as to ease reproducibility of measurement positions. This offers the opportunity of validating aerodynamic and aeroacoustic quantities, obtained from different numerical tools and procedures.

A low pressure axial fan for benchmarking numerical methods in the field of aerodynamics and aeroacoustics is presented. The generic fan for this benchmark is a typical fan to be used in commercial applications. The design procedure was according to the blade element theory for low solidity fans. A wide range of experimental data is available, including aerodynamic performance of the fan (fan characteristic curve), fluid mechanical quantities on the pressure and suction side from laser Doppler anemometer (LDA) measurements, wall pressure fluctuations in the gap region and sound characteristics on the suction side from sound power and microphone array measurements. The experimental setups are described in detail, as to ease reproducibility of measurement positions. This offers the opportunity of validating aerodynamic and aeroacoustic quantities, obtained from different numerical tools and procedures.

This paper discusses various engine installations in Naval aircraft, looking especially at their costs of maintenance. Fuel systems, fuel control systems, and several engine accessories are discussed for present and future engines. It is concluded that simple, reliable equipment is necessary to keep aircraft in the air instead of in maintenance areas on the ground.

This paper describes how airplane control surface rate limiting can enable a ‘cliff-like’ onset of Pilot-Induced Oscillation, (P.I.O.) and how the danger can be erased by implementation of Conditionally Enabled Phase Compensated Rate Limiters, (PCRLs), in the design of the airplane's flight control system. The application is particularly important for large airplanes where control surface actuator sizing and the associated hydraulic system volumetric flow rate capability cannot be generously over-sized without large weight and cost penalties. It is shown that the PCRL can remain inactive during normal airplane operations where RMS control commands are relatively small thus avoiding adverse control surface response effects that have hindered earlier PCRL acceptance.

A short survey of wing tip geometries for drag reduction is presented. These devices have been divided into two broad categories of passive and active. The first category is made of fixed geometries, while the second group is made of those employing moving parts. The former group is further divided into planar and nonplanar designs. In every case, a brief explanation of the underlying logic is given. Altogether, more than fifteen completely different designs and over seventy references have been cited. Some of these designs, such as winglets, have been explored for many years and have proven to be very effective at reducing the induced drag at higher values of lift coefficient. Some others, such as wing tip turbines, have just begun to attract attention. Wing tip fuel tanks, not being solely employed for drag reduction, have not been included in this paper.

A series calculation methodology from the injector nozzle internal flow to the fuel spray was applied to investigate the internal flow and spray of a nozzle whose orifices distributed in different space layers. The nozzle internal flow calculation using an Eulerian three-fluid model and a cavitation model was performed. The needle valve movement during the injection period was taken into account in this calculation. The transient data of spatial distributions of velocity, turbulent kinetic energy, dissipation rate, void fraction rate, etc. at the nozzle exit were extracted. These output data were transferred to the spray calculation, in which a primary break-up model was applied to the Discrete Droplet Model (DDM). The calculation results were compared with the results of the measurement data of spray. Predicted spray morphology and penetration showed good agreement with the experiental data.

The aim of the study is to understand risks associated with a crew member accessing behind the closeout panel or space. Since there is a possibility that a particular closeout space is filled with a harmful gas mixture that is different from the cabin atmosphere, the time needed to ventilate this space should be evaluated. The three-dimensional Computational Fluid Dynamics (CFD) model developed for prediction of time-dependent turbulent flow and concentration fields inside and near a suddenly-opened box is described in the paper. Several cases with different positions of the closeout space, initially filled with pure oxygen, are analyzed under the U.S. Laboratory (USL) ventilation conditions. A simplified flow model, where a suddenly-opened box is ventilated by uniform external throughflow, is considered as well.

Within the frame of a series of initiatives aimed at improving effectiveness of its aircraft design and analysis capabilities, the Military Division of Daimler-Benz Aerospace (Dasa) is developing MIDAS, a multidisciplinary integration framework for a suite of numerical codes suitable to quickly and still accurately assess aircraft performance. As MIDAS specifically targets support of configurational studies in a Conceptual and Preliminary Design environment, peculiar requirements such as scope, range of applicability, and robustness of the system components, reliability of results, care-free operability, and fast response times have to be properly addressed.

An Increase in jet penetration due to the wall boundary layer is determined in the flow field including an aerodynamic interference between the wall boundary layer and the jet. The aerodynamic effect of the wall boundary layer is replaced by that of a secondary vortex filament resulting from vorticity in the wall boundary layer. A differential equation governing the increase in jet penetration is derived using the circulation around the secondary vortex filaments, its induced velocity and the empirical decay law of the jet axial velocity along the jet centerline. The circulation around the secondary vortex filament is estimated according to Hawthorne's theory (1)* and expressed in terms of aerodynamic characteristics of the wall boundary layer. A numerical example of the present analysis shows a fairly good agreement with the experiment. This indicates that the used vortex flow model simulates the real flow conditions well.

A new family of canister-type fuel pumps for use on both rotary and fixed-wing aircraft in general aviation use will be described. The pump, which features a wet-brush DC motor, offers advantages on aircraft where ease of maintenance and minimum downtime is very important. Major features of the new design, pump performance, and maintenance cost savings will be discussed.

This paper documents the design and validation of a closed cycle propulsion system suitable for use on the Perseus A high altitude research aircraft. The atmospheric science community is expected to be the primary user of this aircraft with initial missions devoted to the study of ozone depletion and global warming. To date large amounts of funding are not available to the atmospheric science community, so to be useful, the aircraft must satisfy stringent cost and performance criteria. Among these, the aircraft has to be capable of carrying 50 kg of payload to altitudes of at least 25km, have a initial cost in the $1-2M range, be capable of launch from remote sites, and be available no later than 1994. These operational criteria set narrow boundaries for propulsion system cost, complexity, availability, reliability, and logistical support requirements.