Search Results

A 10 KWe dual-mode space power system concept has been identified which is based on INEL's Small Externally-fueled Heat Pipe Thermionic Reactor (SEHPTR) concept. This power system will enhance user capabilities by providing reliable electric power and by providing two propulsion systems; electric power for an arc-jet electric propulsion system and direct thrust by heating hydrogen propellant inside the reactor. The low thrust electric thrusters allow efficient station keeping and long-term maneuvering. The direct thrust capability can provide tens of pounds of thrust at a specific impulse of around 730 seconds for maneuvers that must be performed more rapidly. The direct thrust allows the nuclear power system to move a payload from Low Earth Orbit (LEO) to Geosynchronous Earth Orbit (GEO) in less than one month using approximately half the propellant of a cryogenic chemical stage.

The in-flight ice accretion simulations are typically performed using a quasi-steady formulation through a multi-step approach. As the ice grows, the geometry changes, and an adaptation of the fluid volume mesh used by the airflow and droplet-trajectory solver is required. Re-meshing or mesh deformation are generally employed to do that. The geometries formed are often complex ice shapes increasing the difficulty of the re-meshing process, especially in three-dimensional simulations. Consequently, difficulties are encountered when trying to automate the process. Contrary to the usual body-fitted mesh approach, the use of immersed boundary methods (IBMs) allows solving, or greatly reducing, this problem by removing the mesh update, facilitating the global automation of the simulation. In the following paper, an approach to perform the airflow and droplet trajectory calculations for three-dimensional simulations is presented. This framework utilizes only immersed boundary methods.

ANY aggregation of parts assembled to obtain a mechanical result is a series of compromises. The relative importance of the objectives governs the nature of the compromise. The major objectives to be considered in the design of airplane engines are (1) Reliability (2) Small weight per horsepower (3) Economy of fuel and oil consumption (4) Carburetion that permits of easy starting; maximum power through a range of 30 per cent of the speed range; and idling at one-quarter maximum speed without danger of stalling (5) Ability to deliver full power through a small speed range without excessive vibration (6) Complete local cylinder-cooling under conditions of high mean effective pressure (7) Compactness The automobile engine must have (1) Reliability (2) Silence (3) Carburetion that accomplishes proper and even firing in all cylinders under varying throttle conditions, through speeds covering more than 90 per cent of the speed range of the engine.

As mission length and the number and complexity of payload experiments increase, so does the probability of thermodegradation contingencies (e.g. fire, chemical release and/or smoke from overheated components or burning materials), which could affect mission success. When a thermodegradation event occurs on board a spacecraft, potentially hazardous levels of toxic gases could be released into the internal atmosphere. Experiences on board the Space Shuttle have clearly demonstrated the possibility of small thermodegradation events occurring during even relatively short missions. This paper will describe the Combustion Products Analyzer (CPA), which is being developed under the direction of the Toxicology Laboratory at Johnson Space Center to provide necessary data on air quality in the Shuttle following a thermodegradation incident.

Both humans and onboard radiosensitive systems (electronics, materials, payloads and experiments) are exposed to the deleterious effects of the harsh space radiations found in the space environment. The purpose of this paper is to present the space radiation environment extended to deep space based on environment models for the moon, Mars, Jupiter, and Saturn and compare these radiation environments with the earth's radiation environment, which is used as a comparative baseline. The space radiation environment consists of high-energy protons and electrons that are magnetically “trapped” in planetary bodies that have an intrinsic magnetic field; this is the case for earth, Jupiter, and Saturn (the moon and Mars do not have a magnetic field). For the earth this region is called the “Van Allen belts,” and models of both the trapped protons (AP-8 model) and electrons (AE-8 model) have been developed.

In designing large booster structures, a major area requiring extensive stress analysis is the discontinuous region, such as the skirt intersection, the sculptured joint, and the reinforced opening. This paper presents a computer solution of stresses and displacement in a typical skirt intersection consisting of (1) a variable-walled transition cylinder, (2) a skirt cylinder, (3) a spheroidal dome, and (4) an infinitely long cylinder. The solution of the variable-walled cylinder is accomplished by integrating numerically a fourth-order differential equation. From the computer analysis the theoretical stresses at the intersection of a typical large-diameter rocket motor case are obtained.

The BSTCA (Battery Section Thermal Control Assembly) is a module of the Columbus MTFF (Man Tended Free Flyer). Electrical power required during eclipse periods, is made available from six nickel hydrogen batteries. A sophisticated multi-radiator configuration, with a hybrid heat pipe network, has evolved. Autonomous control of the assembly heat rejection capability has been achieved by a integrated network of LTHP's (Liquid Trap Heat Pipes) and CCHP's (Constant Conductance Heat Pipes) under the control of a conventional HCU (Heater Control Unit). The process of design selection and verification is discussed, for the BSTCA, with a detailed LTHP component presentation.

Hydrogen has difficulties in handling in a fuel cell vehicle, and has a fault with taking a big space there. The authors have proposed a hydrogen generation system using ammonia as a liquid fuel for fuel-cell electric vehicles. Ammonia has an advantage not to emit greenhouse effect gases because it does not contain a carbon atom. Hydrogen content of ammonia is 17.6 wt% and hydrogen quantity per unit mass is large. Ammonia can be easily dissociated to hydrogen and nitrogen by heating. Therefore, ammonia is an attractive hydrogen supply source for fuel cell vehicles. The ammonia hydrogen generation system of this study consists of a vaporizer, a heat exchanger and a cracking reactor with a separator. Ammonia is heated with the heat exchanger and sent to the cracking reactor, after it is evaporated through the vaporizer from the liquid ammonia. The ammonia is cracked to hydrogen and nitrogen with an appropriate catalyst.

A mean value based sizing and simulation model has been developed for use in the conceptual design and sizing of hydrogen fueled spark-ignition internal combustion engines (HICE) in the aerospace industry, here ‘mean value’ includes mean effective pressure (MEP), mean piston speed, mean specific power, etc. This model is developed since there is currently no such model readily available for this purpose. When sizing the HICE, statistical data and common practice for gasoline internal combustion engines (GICE) are used to obtain preliminary sizes of the HICE, such as total cylinder volume, bore and stroke; to capture the effect of low volumetric efficiency, the preliminary results are adjusted by a volumetric correction factor until the cycle parameters of HICE are reasonable. A non-dimensional combustion model with hydrogen as fuel is incorporated with existing GICE methods. With this combustion model, the high combustion temperature and high combustion pressure are captured.

This paper characterizes the features and describes some of the benefits of the present generation of multigrade “MS” oils. Particular emphasis is placed upon viscosity retention characteristics as a function of the stability of the viscosity index improver. Comparative automobile field tests in private commuter, taxicab, and highway service are shown for both SAE 10W-30 and a carefully compounded SAE 10W-40 oil. Observations of cylinder and piston ring wear, crankcase deposits, PCV valve cleanliness, and oil economy are reported.

CONTINUOUS increase in the power output of aircraft engines introduces from time to time lubricating problems including excessive wear and scuffing, excessive oxidation of the oil, and ring sticking. The one problem of ring sticking was chosen and the discussion is limited to the testing of lubricating oils to compare their abilities to prevent this type of failure. Although the best answer as to the ring-sticking tendencies of a lubricant rests with the full-scale engine in service, a simple test is needed during the development period. The development work which led up to the selection of an L-head CFR engine for a ring-sticking test is discussed. Various criteria used for detecting incipient ring sticking are mentioned and a method for direct measurement of incipient ring sticking is described.

The carbothermal reduction of ilmenite and iron- bearing silicates are important in the manufacture of steel and perhaps for manufacture of oxygen on the moon. Oxygen recovery from ilmenite and iron silicates is of interest because of the abundance of such minerals on the lunar surface and the relative ease of their reductions. A novel carbothermal reduction process is developed for the reduction of these minerals. This presentation summarizes an experimental study of the carbothermal reduction of ilmenite and iron-bearing silicates at temperatures between 850°C and 1100°C. Extremely high reduction rates are observed and investigated for carbothermal reduction of ilmenite by using deposited carbon. These results are compared to previous kinetics studies with regards to the different activation energy values reported.

New environmental regulations all over the world encourage the use of alternatives to cadmium plating for corrosion-protection systems used on steels. Boeing patents are pending on a non-cyanide replacement zinc-nickel alloy electroplating process with superior properties, including low hydrogen embrittlement and good corrosion protection, for use on high-strength steels and other substrates. Another advantage of this process is low cost because conventional electroplating tank facilities can be used and waste treatment cost can be reduced. The feasibility of this zinc-nickel plating process has been successfully demonstrated in the laboratory and is scheduled for manufacturing scale-up during 1983.

Aircraft manufacturers spend millions of dollars reworking blown fastener holes, especially in portable tool drilling situations. Oval, tapered, rifled, and oversize holes are costly rework issues currently commonplace in the industry. The most common causes of imperfectly drilled holes include spindle runout, insufficient clamp and feed force, out-of-balance drill feed forces, spindle windup, and lack of adequate feed control. This paper will focus on a next-generation drilling machine that utilizes a unique combination of hydraulics and pneumatics to solve the problems associated with legacy drilling units. Several design elements will be examined, such as the use of an on-board, 1000 PSI hydraulic pump, controlling both drill feed and clamp force. This greatly reduces the size and weight of the clamp and feed cylinders compared to legacy air systems, while increasing their force and rigidity.

The Naval Research Laboratory (NRL) and Johnson Controls Inc. (JCI) have joined together in a cooperative research and development effort to “space qualify” the JCI Common Pressure Vessel (CPV) Nickel Hydrogen (NiH2) battery. JCI is providing two (2) NiH2 batteries to NRL. One is for qualification tests and the second is for the flight experiment. NRL is responsible for the design, test and integration of the battery with an existing spacecraft electrical power system, launch of the battery with the host spacecraft, and providing data from the flight experiment. Since the intent of the experiment is to “space qualify” the JCI NiH2 CPV design, the battery will be “on-line” and fully charged during the launch of the host spacecraft. This paper will describe the NRL-JCI Cooperative Research and Development Agreement, the NiH2 CPV battery experiment design, and the qualification test program.

A newly-invented "X"-configuration engine utilizing the Scotch yoke mechanism renders potential for the best power/weight ratio of any piston engine. Due to its inherent space and weight efficiency, low stress levels on critical components and low bearing pressures, this new configuration can be designed for aircraft applications using high-pressure 4-stroke diesel cycle with large numbers of cylinders - as many as 24 or 32 cylinders - to minimize engine weight and cross-sectional area. Given the efficiency advantage of 4-stroke turbo-diesel cycle over turbine engines, a study reveals that diesel X-engines may be a preferable solution to turbine engines for airplanes, helicopters and UAVs up to approximately 60000 lbs max. weight @takeoff. Calculations using existing turbine-powered aircraft as a baseline indicate potential for 35 to 50% lower fuel consumption with no compromise to maximum takeoff weight, payload, range, cruise speed, maximum speed or takeoff power.

This paper presents a mathematical model of the vertical forces acting on an airship during vertical motion. The main effort is the definition of an airship model, which move only vertically by ballast, and buoyancy effects, with a much reduced energy consumption for take-off and landing operations. It has been considered a disc-shaped airship, which can operate using the open balloon airship architecture defined to operate safely with hydrogen. This architecture does not require internal ballonets, because of the connected increased fire dangers that they create even if vented. Several models of airship based on vertical forces have been presented in literature. They often consider only the US or International Standard Atmosphere models and they neglect effects of weather conditions. The latter are connected with the location and with the season.

The crankcase-scavenged two-stroke-cycle engine is preferred in cases where low weight and high power output are paramount requirements. These qualities are most important in small pilotless aircraft. It was found that the main problem in the use of two-stroke cycle engines for this purpose, is a sharp decrease in the engine power with the increase in altitude. This is attributed not only to the low density of the ambient air, but also to the deterioration of the efficiency of the gas exchange process. In order to improve the engine performance at high altitude, it is proposed here to employ a stepped-piston engine. The engine is constructed of a stepped piston and a single stepped cylinder thus forming three compartments; a power, a compression and a crankcase compartment. In this arrangement, the fresh charge is compressed in the compression compartment before it enters the crankcase compartment.

The kinetics of the Sabatier methanation reaction, the reduction of carbon dioxide with hydrogen to methane and water, was investigated for 58 percent nickel on kieselguhr catalyst and 20 percent ruthenium on alumina catalyst. Differential rate data from an experimental program were correlated with a power function rate equation both for forward and reverse reactions. The kinetic parameters of activation energy, frequency rate constant and reaction order were determined for the rate equation. The values of these parameters were obtained from an Arrhenius plot of the experimental differential rate data. Also the carbon monoxide side reaction effect was measured and included in the correlation of parameters. The reaction was found to fit the rate equation experimentally within the temperature range 421°K, where the reaction effectively begins, to 800°K where the reaction rate drops and departs from the rate equation form.

The Diagnostics Tested Facility (DTF) at NASA's John C. Stennis Space Center (SSC) in Mississippi was designed to provide a testbed for development of rocket engine exhaust plume diagnostics instrumentation. A 1200-lb thrust liquid oxygen (LOX)/gaseous hydrogen (GH2) thruster is used as the plume source for experimentation and instrument development. Theoretical comparative studies have been performed with aero-thermodynamic codes to ensure that the DTF thruster (DTFT) has been optimized to produce a plume with pressure and temperature conditions as much like the plume of the Space Shuttle Main Engine (SSME) as possible. Operation of the DTFT is controlled by an icon-driven software program using a series of soft switches. Data acquisition is performed using the same software program. A number of plume diagnostics experiments have utilized the unique capabilities of the DTF.