Search Results

An effective ground station is vital to the successful implementation of an EMS and is a fundamental part of the total monitoring system design. Unlike on-board processing systems which principally use data to indicate when engine maintenance is required, ground stations offer much greater processing power to analyse and manipulate EMS data more comprehensively for both maintenance and logistics purposes. This document reviews the main EMS functions and discusses the operating requirements which will determine the basic design of a ground station, including the interfaces with other maintenance or logistics systems. A brief discussion is also included on some of the more recent advances in EMS ground station technology which have been specifically developed to provide more effective diagnostic capabilities for gas turbine engines. Finally, this document addresses the program management requirements associated with the initial development and on-going support of a ground station.

The purpose of this SAE Aerospace Information Report (AIR) is to provide management, designers, and operators with information to assist them to decide what type of power train monitoring they desire. This document is to provide assistance in optimizing system complexity, performance and cost effectiveness. This document covers all power train elements from the point at which aircraft propulsion energy in a turbine or reciprocating engine is converted via a gear train to mechanical energy for propulsion purposes. The document covers aircraft engine driven transmission and gearbox components, their interfaces, drivetrain shafting, drive shaft hanger bearings, and associated rotating accessories, propellers, and rotor systems as shown in Figure 1. For guidance on monitoring additional engine components not addressed, herein (e.g., main shaft bearings and compressor/turbine rotors), refer to ARP1839.

The process detailed within this document is generic and can be applied to commercial and military applications. It applies to the entire end-to-end health management system throughout its lifecycle, covering on-board and on-ground elements. The practical application of this standardized process is detailed in the form of a checklist. The on-board element described here are the source of the data acquisition used for off-board analysis. The on-board aspects relating to safety of flight, pilot notification, etc., are addressed by the other SAE Committees standards and documents. This document does not prescribe hardware or software assurance levels, nor does it answer the question “how much mitigation and evidence are enough”. The criticality level and mitigation method will be determined between the ‘Applicant’ and the regulator.

This SAE Aerospace Recommended Practice (ARP) provides guidance for the design of flanges on temperature sensors intended for use in gas turbine engines. Three figures detail the configuration of standard size flange mounts with bolt holes, slotted flanges, and miniaturized flanges for small probes.

The purpose of this SAE Aerospace Information Report (AIR) is to provide information and guidance for the selection and use of oil system monitoring devices and methods. This AIR is intended to be used as a technical guide. It is not intended to be used as a legal document or standard. The scope of this document is limited to those inspection and analysis methods and devices that can be considered appropriate for routine maintenance. In agreement with industry usage, wear particle size ranges are given in micrometers (1 μm = 10-3 mm = 10-6 m).

The effectiveness of Engine Life Usage Monitoring and Parts Management systems is largely determined by the aircraft-specific requirements. This AIR addresses the following areas: a Safety. b Life-limiting criteria. c Life usage algorithm development. d Data acquisition and management. e Parts life tracking. f Design feedback. g Cost effectiveness. This AIR primarily examines the requirements and techniques currently in use, including: a Parts classification and control requirements. b Failure causes of life-limited parts. c Engine life prediction and usage measurement techniques. d Method validation. e Parts life usage data management. f Lessons learned. g Life usage tracking benefits.

The purpose of this Aerospace Information Report (AIR) is to provide information and guidance for the selection and use of oil system monitoring devices and methods. This AIR is intended to be used as a technical guide. It is not intended to be used as a legal document or standard. The scope of this document is limited to those inspection and analysis methods and devices which can be considered appropriate for routine maintenance. In agreement with industry usage, wear particle size ranges are given in μm (1 μm = 10-3 millimeter = 10-6 meter). Other dimensions are given in millimeters, with inches in parenthesis.

This SAE Aerospace Information Report (AIR) provides information and guidance for the selection and use of technologies and methods for lubrication system monitoring of gas turbine aircraft engines. This AIR describes technologies and methods covering oil system performance monitoring, oil debris monitoring, and oil condition monitoring. Both on-aircraft and off-aircraft applications are presented. A higher-level view of lubrication system monitoring as part of an overall engine monitoring system (EMS), is discussed in ARP1587. The scope of this document is limited to those lubrication system monitoring, inspection and analysis methods and devices that can be considered appropriate for health monitoring and routine maintenance. This AIR is intended to be used as a technical guide. It is not intended to be used as a legal document or standard.

The purpose of this SAE Aerospace Information Report (AIR) is to provide information and guidance for the selection and use of lubrication system monitoring methods. This AIR is intended to be used as a technical guide. It is not intended to be used as a legal document or standard. The scope of this document is limited to those inspection and analysis methods and devices that can be considered appropriate for routine maintenance.

The effectiveness of Engine Life Usage Monitoring and Parts Management systems is largely determined by the aircraft-specific requirements. This document addresses the following areas: a Safety b Life-limiting criteria c Life usage algorithm development d Data acquisition and management e Parts life tracking f Design feedback g Cost effectiveness It primarily examines the requirements and techniques currently in use, and considers the potential impact of new technology to the following areas: a Parts classification and control requirements b Failure causes of life-limited parts c Engine life prediction and usage measurement techniques d Method validation e Parts life usage data management f Lessons learned g Life usage tracking benefits

This document applies to prognostics of gas turbine engines and its related auxiliary and subsystems. Its purpose is to define the meaning of prognostics with regard to gas turbine engines and related subsystems, explain its potential and limitations, and to provide guidelines for potential approaches for use in existing condition monitoring environments. It also includes some examples.

The ice bath recommended herein is similar to that described in SAE AIR 46.* Some material not presented in AIR 46, including preferred dimensions, has been added.

To establish a specification for software input and output interfaces for condition monitoring and performance programs used to monitor equipment from multiple manufacturers. The purpose of standardizing these interfaces is to improve operational flexibility and efficiency of monitoring systems as an aid to cost effectiveness (e.g., easier implementation).

This SAE Aerospace Recommended Practice (ARP) defines the nomenclature of temperature measuring devices. General temperature measurement related terms are defined first, followed by nomenclature specific to temperature measuring devices, particularly thermocouples.

This SAE Aerospace Information Report (AIR) reviews the precautions that must be taken and the corrections which must be evaluated and applied if the experimental error in measuring the temperature of a hot gas stream with a thermocouple is to be kept to a practicable minimum. Discussions will focus on Type K thermocouples. These are defined in NBS Monograph 125 as nickel-chromium alloy versus nickel-aluminum alloy thermocouples.

This SAE Aerospace Information Report (AIR) reviews the precautions that must be taken and the corrections which must be evaluated and applied if the experimental error in measuring the temperature of a hot gas stream with a thermocouple is to be kept to a practicable minimum. Discussions will focus on Type K thermocouples, as defined in National Institute of Standards and Technology (NIST) Monograph 175 as Type K, nickel-chromium (Kp) alloy versus nickel-aluminium (Kn) alloy (or nickel-silicon alloy) thermocouples. However, the majority of the content is relevant to any thermocouple type used in gas turbine applications.