Search Results

Growing concern over the health effects of airborne particles and a desire to reduce the associated cost has resulted in legislation, regulations and other measures, in the industrialised world to severely restrict particulate emissions from diesel-fuelled automotive transport. Developing countries are also introducing initiatives to try and reduce emissions, an example is the legislation in India to replace diesel engines with gas fuelled engines in some major conurbations. Such measures are expensive, both in terms of replacing the engines of the vehicles and of implementing the required infrastructure. There is still also debate over whether such measures reduce the number of ultra-fine particulates. A well-proven alternative is to fit diesel engines with Diesel Particulate Filters (DPFs), either as original equipment or as a retrofit system. Regenerating DPFs has in the past been an obstacle to their widespread application.

Fuel-borne catalysts are now an accepted means of aiding the self-regeneration of diesel particulate filters (DPFs). In the past it has been possible to assess the effect of these fuel additives by investigating the temperature at which the filter reaches a pressure drop equilibrium. Under these temperature conditions, the particulate matter is oxidised at the same rate as it is being deposited and there is thus no change in pressure drop across the filter. This technique adequately demonstrates the oxidation temperature of the carbon in the presence of the catalyst. However, it is now well known that such fuel additives also influence the low temperature oxidation of particulate bound hydrocarbons. This phenomenon is not detected by the filter equilibrium technique.

A novel dosing system for fuel borne catalyst (FBC), used to assist regeneration with a diesel particulate filter (DPF), has been developed. The system was designed for on-board vehicle use to overcome problems encountered with batch dosing systems. Important design features were simplicity, to minimise system cost, and the use of in-line dosing rather than batch dosing linked to tank refuelling. The paper describes the development of the dosing system which continuously doses FBC into the fuel line feeding the engine injection pump. The theoretical considerations behind the concept are explored, together with the realities imposed by fuelling regimes in which a variable proportion of the fuel flowing through the injection pump is passed back to the fuel tank. Two types of system are considered, ie where 1) FBC is added to the fuel in direct proportion to the flow rate of fuel and 2) FBC is added at a constant time-based rate.

The operating cycle of many vehicles fitted with diesel particulate filters is such that soot accumulates within the filter and must periodically be oxidised. Work was carried out on a passenger car engine to elucidate how fuel borne catalyst (FBC) to soot ratio, oxygen mass flow rate, temperature and soot loading influence the oxidation rate of soot accumulated in a sintered metal filter (SMF). Results show that soot loading had a major influence; increased soot loading increased the oxidation rate. The other parameter had a smaller influence with increasing oxygen flow rate and FBC/soot ratio each increasing the oxidation rate.

Diesel particulate filter (DPF) are well known as a developing form of exhaust after-treatment for compression ignition engines. Subjected to extensive testing in experimental form, DPFs have yet to achieve widespread application in regular use on production road vehicles, despite their potential for delivering reductions of typically 90% in diesel exhaust particulate emissions. Tests have shown that different additives are effective in enhancing performance in a range of DPF types, and on engines of different configurations. Efforts have been made to correlate performance with engine operating regime, by linking soot particulate condition to the frequency of regeneration. A performance index has been developed to try to predict regeneration characteristics with additive treated fuel. The work has shown that there are engine operating conditions producing soot which is less likely to burn off in the DPF.

In view of increasing concern over diesel particulates and tightening legislation to control their emission, much work has been done to develop diesel particulate filters (DPFs) and systems to allow them to work reliably. Although a filter will effectively trap solid particles, any material in the vapour phase, such as unburned hydrocarbons, may pass through the filter and subsequently condense. The use of a catalytic wash coat, either on the DPF itself or on a separate substrate, has been proposed to oxidise these hydrocarbons and thus reduce the total material emitted. The use of fuel borne catalysts to aid the regeneration of trapped material within the DPF is also well documented. Such catalyst will also catalyse the oxidation of any hydrocarbons bound up within the particulate. The oxidation of such hydrocarbon occurs at a lower temperature than that of carbon itself, thus allowing lower temperature regeneration of the DPF.

The most cost-effective way to reduce the level of diesel particulate emissions is to retrofit exhaust aftertreatment devices. While diesel oxidation catalysts will reduce the mass of particles emitted, they will not significantly reduce the number of ultrafine particles, that are considered the most harmful to health. Diesel Particulate Filters (DPFs) are therefore considered the most effective retrofit devices. One obstacle to the widespread adoption of DPFs is that many DPF technologies require low sulphur fuel. Using a Fuel Borne Catalyst (FBC) to facilitate regeneration of the DPF allows a sulphur tolerant DPF system to be produced.

Future emissions limits are pushing vehicle manufacturers towards the fitting of Diesel Particulate Filters (DPFs) as original equipment. However due to the replacement rate of the vehicle fleet, there is a delay before the full benefit of these measures are fully realised. To overcome this problem, in areas with a particular problem such as heavily congested city centres, retrospective legislation has been, and may be introduced. Legislation mandating the retrofitting of DPFs obviously has an immediate effect on particulate emissions. In some countries including the UK there are also fiscal incentives to fit DPFs. Due to its duty cycle the London taxi or Black Cab is one of the more challenging areas of application for the DPF. Previous work has shown that the use of a fuel borne catalyst (FBC) can extend the operating range of DPF systems providing the possibility of a viable system for such applications.

There is mounting worldwide concern over the health effects of airborne ultra-fine particles. Of greatest concern are the risks due to the cancer-inducing properties of these particles and the aggravation of existing respiratory diseases by the ultra-fine (i.e. <2.5 micron) fraction. This disquiet has already resulted in legislation, regulations and other measures, either mandated or proposed, in the industrialised world to severely restrict particulate emissions from diesel-fuelled automotive transport. Emissions of particles from both new and existing vehicles have been addressed. With the rapid growth anticipated in some developing countries they to will need to address this problem. This paper outlines some alternative solutions to the problem, ranging from alternative power sources, alternative fuels, alternative engine technologies and after-treatment strategies. It also outlines what is required to implement these different solutions.

Four vehicles were chosen to cover a range of engine technologies. These vehicles were fitted with diesel particulate filters (DPFs) of differing technology. Three of the vehicles have been driven on the road using an additised fuel to demonstrate totally passive operation of the DPF. As part of this programme all three vehicles underwent regulated emissions testing to demonstrate that there was no deterioration in emissions during the programme. Additionally a light commercial vehicle was tested to demonstrate the effect on emissions of the combination of additised fuel and the DPF. The performance of the DPFs during on-road use has already been reported; this paper therefore concentrates on discussion of the results of the emissions testing.

Forthcoming emissions legislation is driving the passenger car manufacturers towards the fitting of Diesel Particulate Filters (DPFs) as original equipment. However such initiatives are not retrospective and due to the replacement rate of the vehicle fleet, there is a time lag before the full benefit of the new measures are fully realised. To overcome this drawback, in areas with a particular problem such as heavily congested city centres, retrospective legislation has been introduced, for example in Hong Kong and Tokyo. Legislation mandating the retrofitting of DPFs obviously has an immediate effect on particulate emissions. Other authorities are thus investigating the efficacy of such measures. To add to the data base for such assessments Octel is running a demonstration programme using London Black Cabs. Four cars have been fitted with a DPF, an on-board dosing system to meter a fuel borne catalyst (FBC) into the fuel and a data logger to monitor the DPF performance.

Forthcoming emissions legislation is driving the passenger car manufacturers towards the fitting of Diesel Particulate Filters (DPFs) as original equipment. In areas with a particular problem such as heavily congested city centres, retrospective legislation has also been introduced, for example in Hong Kong and Tokyo. Legislation mandating the retrofitting of DPFs obviously has an immediate effect on particulate emissions. Other authorities are thus investigating the efficacy of such measures. However with the increasing use of DPF technology concerns are now being raised over some currently unregulated emissions such as ultra fine particulate and NO2, although total particulate mass and oxides of nitrogen are regulated. To add to the data base for such issues a programme of work was run using London Black Cabs. Four cars were fitted with a DPF, an on-board dosing system to meter a fuel borne catalyst (FBC) into the fuel and a data logger to monitor the DPF performance.

For many years now, epidemiologists have been highlighting the potential damage to health and the associated cost, caused by diesel particulate emissions. There is still debate concerning the crucial characteristics of these particles, however many authorities have concluded that it is their duty to legislate the reduction of such emissions. The most common approach is to legislate that all new vehicles should meet ever stricter emissions limits. This puts the onus and the cost on the engine manufacturers. The emissions limits in developing countries are inevitably less stringent than those in the developed world, this gives the indigenous manufacturers the opportunity to compete and develop. However, vehicle replacement intervals dictate that the effect of legislation controlling new vehicles takes many years to propagate throughout the existent vehicle fleet.

Diesel particulate filter (DPF) technology is becoming increasingly established as a practical method for control of particulate emissions from diesel engines. In the year 2000, production vehicles with DPF systems, using metallic fuel additive to assist regeneration, became available in Europe. These early examples of first generation DPF technology are forerunners of more advanced systems likely to be needed by many light-duty vehicles to meet Euro IV emissions legislation scheduled for 2005. Aspects requiring attention in second generation DPF systems are a compromise between regeneration kinetics and ash accumulation. The DPF regeneration event is activated by fuel injection, either late in the combustion cycle (late injection), or after normal combustion (post injection), leading to increased fuel consumption. Therefore for optimum fuel economy, the duration of regeneration and/or the soot ignition temperature must be minimised.

Interest has been growing in many countries in the potential use of diesel particulate filters (DPF). This type of after treatment technology has been shown to make very significant reductions in both the mass of particulate emitted in diesel exhaust gas, and also in the number of fine particulates, which have been linked in recent years with concerns for human health. Work carried out during a development programme investigating the capability of fuel soluble metallic additives to assist DPF regeneration, indicated superior performance from a novel combination of metals in fuel soluble form. Earlier work showed that a fuel soluble combination of organo-metallic additives based on sodium and strontium gave very effective regeneration characteristics, and was capable of burning out carbon at temperatures from about 160°C.

Due to concerns over NO2 emissions from platinum catalysts a base metal catalysed diesel particulate filter (DPF) has been developed and used in combination with fuel borne catalysts (FBC). Results are presented showing reductions in HC, NOX, NO2, and PAH emissions along with an assessment of the emissions of metals used in the FBC and the catalysed DPF. This data is used to show the likely reduction in overall iron and other metal emissions as a result of using the catalysed DPF/FBC system. A similar system has also been assessed for durability for over 2000 hours when fitted to a bus in regular service in Switzerland.

One of the most promising ways to insure the periodic regeneration of a particulate trap, consists of additising the fuel with organo-metallic compounds. The present paper deals with a novel alkali product, able to promote natural regenerations, for exhaust temperatures as low as 200 °C, and treatment rates as low as 5 ppm metal. Tests have been carried out on a soot reactor and on an engine bench, with various trap locations in the exhaust, showing that the regeneration occurrence depends on temperature, soot mass loaded inside the porous structure and engine conditions. A complete trap cleaning still needs gas temperatures up to 400 °C, which can be encountered for high load conditions of the engine.

Work was carried out on three passenger cars and a light truck. The test vehicles were chosen to cover a range of engine technologies. Different DPF technologies were also employed. The programme showed that an improved fuel additive based on the combination of iron and strontium compounds would allow all four vehicles to be successfully operated under a wide range of conditions. The three passenger cars were driven over the road for considerable distances. Regeneration of the DPF was successfully achieved under normal operating conditions in all the vehicles without recourse to use of additional heaters, fuel injection or other technique to assist regeneration. Fuel additive treat rate was low, suggesting that long-term operation without significant ash accumulation in the DPF could be achieved.

Exhaust emissions legislation for diesel engines generally limits only the mass of emitted particulate matter. This limitation reflects the concerns and measurement technology at the time the legislation was drafted. However, evolving diesel particulate filter (DPF) systems offer the potential for reductions in the mass and more importantly, the number of particles emitted from diesel exhausts. Particulate filters require frequent cleaning or regeneration of accumulated soot, if the engine is to continue to operate satisfactorily. Exothermic reactions during regeneration can lead to severe thermal gradients in the filter system resulting in damage. Fuel additives have been evaluated to show significant reductions in light off temperature which allow frequent small regeneration events to occur, under mild operating conditions.

Continuing research into the effect of vehicle emissions is driving legislation, which is increasingly being enacted to encourage the retrofitting of emissions control devices. Of particular concern are emissions of diesel particulate matter and nitrogen oxides. More recently the adverse effects of nitrogen dioxide in particular, have been highlighted. A programme of work is underway in Santiago to demonstrate the suitability of retrofitting diesel particulate filters (DPF) to urban buses. This paper presents data, including regulated and unregulated emissions, from a bus fitted with a DPF that relies on a fuel borne catalyst (FBC) to facilitate regeneration of the DPF.