Search Results

This paper studies the drivability of Hybrid Electric Vehicles (HEV), and presents some methods to improve the drivability based on experiment results. First, the working principle of HEV is introduced and the hybrid powertrain is modeled. The jerk of vehicle is applied in this paper to evaluate the drivability of HEV. After studying the cause of jerk, a series of experiments of vehicle starting, state-changing, shifting and braking are designed and implemented on a parallel HEV with an automated mechanical transmission. Analysis of these experiment results shows that optimization of clutch control and cooperation of the engine and the motor on speed and torque are effective in reducing the jerk of vehicle.

Active collision avoidance can assist drivers to avoid longitudinal collision through active brake. Regenerative braking can improve the driving range and braking response speed. At this stage, conventional hydraulic braking system limits the implements of above technologies because of its poor performance of response speed and coordinated control. While the brake-by-wire system is a better actuator that can fulfill requirements of automotive electric and intelligent development due to its rapid response and flexible adjustment. However, the system control algorithm becomes more complicated with introduction of regenerative braking and active collision avoidance function, which is also the main problem solved in this paper.

This paper presents a coordinated controller for comprehensive optimization of vehicle dynamics performance and energy consumption for a full drive-by-wire electric vehicle, which is driven by a four in-wheel motor actuated (FIWMA) system and steered by a steer-by-wire (SBW) system. In order to coordinate the FIWMA and SBW systems, the mechanisms influencing the vehicle dynamics control performance and the energy consumption of the two systems are first derived. Second, the controllers for each subsystem are developed. For the SBW system, a triple-step control technique is implemented to decouple the yaw rate and sideslip angle controls. The FIWMA system controller is designed with a hierarchical control scheme, which is able not only to satisfy the yaw rate and sideslip angle tracking demands, but also to deal with actuation redundancy and constraints.

In this paper, gear ratios of a two-speed transmission system are optimized for an electric passenger car. Quasi static system models, including the vehicle model, the motor, the battery, the transmission system, and drive cycles are established in MATLAB/Simulink at first. Specifically, since the regenerative braking capability of the motor is affected by the SoC of battery and motors torque limitation in real time, the dynamical variation of the regenerative brake efficiency is considered in this study. To obtain the optimal gear ratios, iterations are carried out through Nelder-Mead algorithm under constraints in MATLAB/Simulink. During the optimization process, the motor efficiency is observed along with the drive cycle, and the gear shift strategy is determined based on the vehicle velocity and acceleration demand. Simulation results show that the electric motor works in a relative high efficiency range during the whole drive cycle.

A novel type of regenerative braking system for electric vehicles is proposed in this paper. Four pressure-difference-limit valves, two relief valves and two brake pedal simulators, are added to the layout of a conventional four-channel hydraulic modulator. The cooperation of relief valves and hydraulic pumps provides a stabilized high-pressure source. Pressure-difference-limit valves ensure that the pressure in each wheel cylinder can be modulated separately at a high precision. Besides, the functions of anti-lock braking system and electronic stability program are integrated in this regenerative braking system. The models of regenerative braking controller and vehicle dynamics are built in MATLAB/Simulink. Hydraulic brake model is built in AMESim through a parameterized and modularized method. Meanwhile, the control strategy of hydraulic brake modulation and brake force distribution are designed.

As one of the key technologies of electrified vehicles, regenerative braking offers the capability of fuel saving by converting the kinetic energy of the moving vehicle into electric energy during deceleration. To coordinate the regenerative brake and friction brake, improving regeneration efficiency and guaranteeing brake performance and brake safety, development of special brake systems for electrified vehicles is needed. This paper presents a new type of electrically-controlled regenerative braking system (EABS) that has been developed for electrified passenger vehicles, which has the potential to be brought into production in China. By utilizing as much as possible mature components, integrating cooperative regeneration with ABS/TCS functions, EABS can achieve high regeneration efficiency and brake safety while providing system reliability, low development cost and development risk. This article describes the layout of the newly developed regenerative braking system.

A novel fault tolerant brake strategy for In-wheel motor driven electric vehicles based on integral sliding mode control and optimal online allocation is proposed in this paper. The braking force distribution and redistribution, which is achieved in online control allocation segment, aim at maximizing energy efficiency of the vehicle and isolating faulty actuators simultaneously. The In-wheel motor can generate both driving torque and braking torque according to different vehicle dynamic demands. In braking procedure, In-wheel motors generate electric braking torque to achieve energy regeneration. The strategy is designed to make sure that the stability of vehicle can be guaranteed which means vehicle can follow desired trajectory even if one of the driven motor has functional failure.

This paper defines a control method for shift torque exchange stage and a torque distribution control method for speed regulation stage. In the torque exchange stage, the torque distribution problem of active and passive clutches considers the injection of sine curve for local correction, which can solve the fish belly problem of hydraulic response (i.e. the hydraulic response is slow at the beginning and the hydraulic response is fast at the end). In the speed regulation stage, the target speed gradient profile is determined according to different shift types. The determination of the target speed gradient profile integrates different driving modes, throttle, P2 energy and clutch temperature.

With the rise of new energy vehicle industry as a national strategy, China has gradually occupied an absolute leading position in the field of battery electric vehicles, especially commercial battery electric vehicles, and has taken the lead in the research and development of dual-motor coupling propulsion technology. Due to the complex and diversiform structure of multi-source power speed-variable propulsion system, there is no mature configuration and technical details. Also, the control problem is a typical hybrid system problem, and there is no unified and clear problem description and solution method. In addition, the current research on the mode switching derived from the novel electrified powertrain is not deep enough to fully explore the potential advantages of electromechanical driveline, and there is a certain research blank considering the online implementation.

As the essential of future driver assistance system, brake-by-wire system is capable of performing autonomous intervention to enhance vehicle safety significantly. Regenerative braking is the most effective technology of improving energy consumption of electrified vehicle. A novel brake-by-wire system scheme with integrated functions of active braking and regenerative braking, is proposed in this paper. Four pressure-difference-limit valves are added to conventional four-channel brake structure to fulfill more precise pressure modulation. Four independent isolating valves are adopted to cut off connections between brake pedal and wheel cylinders. Two stroke simulators are equipped to imitate conventional brake pedal feel. The operation principles of newly developed system are analyzed minutely according to different working modes. High fidelity models of subsystems are built in commercial software MATLAB and AMESim respectively.

Regenerative braking, which can effectively improve vehicle's fuel economy by recuperating the kinetic energy during deceleration processes, has been applied in various types of electrified vehicle as one of its key technologies. To achieve high regeneration efficiency and also guarantee vehicle's brake safety, the regenerative brake should be coordinated with the mechanical brake. Therefore, the regenerative braking control performance can be significantly affected by the structure of mechanical braking system and the brake blending control strategy. By-wire brake system, which mechanically decouples the brake pedal from the hydraulic brake circuits, can make the braking force modulation more flexible. Moreover, its inherent characteristic of ‘pedal-decouple’ makes it well suited for the implementation in the cooperative regenerative braking control of electrified vehicles.

Due to the objectives of achieving high fuel efficiency and drivability performance, a dual-drive hybrid system with two motors has been developed. Various drive modes are presented based on engine status, requested driver torque and power, as well as C0 status in different working conditions. The transition control of drive mode change poses a unique challenge for the dual-drive hybrid system. This study discusses the control strategies for transitioning between drive modes. The first type of transition mode is divided into four distinct phases. In the second mode transition, there are three phases: the synchronization phase involving P1 torque intervention, the C0 lock-up phase involving frozen P1 torque control and adjustment of C0 clutch torque and pressure correlation, and finally, the torque exchange phase. The third type of transition includes a dedicated torque transition phase followed by a C0 disengaged phase and concluding with a speed synchronization phase.

In order to solve the problems of the shuffle caused by internal and external excitation and the difficulty in obtaining the real-time accurate engine torque during the parallel mode operation of hybrid electric vehicles, a dynamic coordination control strategy for suppressing the jitter of hybrid electric vehicles based on the closed-loop control of engine speed was proposed. The engine torque filtering control method based on the slope limit was adopted to limit the rate of change of the engine torque and reduce the impact caused by the sudden change of the engine torque; the engine speed closed-loop control method was used to take the motor speed which is easy to be measured accurately in real time as the feedback control variable, which solved the problem of the real-time accurate estimation of the engine torque online. In parallel mode, the motor torque accounts for a small proportion because the torque distribution method gives priority to the engine.

In hybrid vehicles, the drive motor is directly connected to the drive train and the inherent drive train damping is low. When subjected to external disturbance, the low damping characteristics of the transmission system may cause torsional vibration, which will continue to oscillate the transmission system and affect the driving performance of the vehicle. In this paper, we propose a harmonic injection wheel control method based on motor speed to suppress oscillations and improve the driving performance of hybrid electric vehicles. The harmonic injection control method based on motor speed is based on Fourier transform to decompose sinusoidal harmonics based on specific order of motor speed. RLS algorithm is used to estimate the amplitude and phase, and PI control is used to calculate the compensation torque for the actual amplitude and target amplitude. Simulation and test results show that the proposed control strategy is effective in suppressing oscillations.

DHT hybrid transmission assembly control system discussed in this paper includes hydraulic control, hybrid mode switching control, shift control, dual motor control, clutch and motor thermal management. The hybrid mode is divided into four modes: the EV mode, the serial mode, the parallel mode and the launch mode. Hydraulic control includes torque-pressure conversion, clutch pressure kiss point adaption, clutch oil filling time adaption. Shift control includes shift type decision, shift sequence control, shift inertia process based on motor intervention. Thermal management includes clutch flow and motor flow distribution. Motor control include the current control, mode control and boost strategy of permanent magnet synchronous motor in dual hybrid system, which has good stability and robustness. Motor mode includes initialization mode, normal mode, fault mode, active discharge mode, power off mode.

In order to realize the shift control of dual-motor hybrid electric vehicle (HEV), a non-power interruption shift control method based on three-power source coordination control was proposed by analyzing the shift process of dual-motor hybrid configuration. The shift control process was divided into three stages: oil-filling self-learning stage, torque exchange stage and inertia control stage. In the torque exchange stage, the characteristics of the speed stage and torque stage were analyzed, which was different from the traditional method's dependence on pressure sensor, longitudinal acceleration sensor and engine torque accuracy. A shift clutch gain self-learning strategy based on shift time and input shaft speed soaring problem was proposed.

In order to achieve seamless mode switching control for hybrid electric vehicles (HEVs) in the event of battery failure, we propose a motor voltage-controlled mode switching method that eliminates power interruptions. This approach is based on an analysis of the dual-motor hybrid configuration's mode switching. We analyze the overall vehicle operation when the high-voltage battery occurs in different hybrid modes. To ensure that the vehicle can still function like a conventional car under such circumstances, we introduce a novel "voltage control" mode. In this mode, instead of operating in its traditional torque control manner, the P1 motor adopts a voltage control strategy. The P1 controller's variable becomes "voltage," and VCU sends the motor's working mode switching request and PCM finishes the mode transition. During system operation, the P1 motor promptly responds to these target voltages to maintain bus voltage within a normal range.

In order to realize the series-parallel switching control of hybrid electric vehicle (HEV) with dual-motor hybrid configuration, a method of unpowered interrupt switching based on the coordinated control of three power sources was proposed by analyzing the series-parallel driving mode of the dual-motor hybrid configuration. The series to parallel switching process is divided into three stages: speed regulation stage, clutch combination and power source switching. The distribution control of speed regulating torque is carried out in the speed regulating stage. The speed adjustment torque is preferentially allocated to the power source of the input shaft (engine and P1) to carry out the lifting torque. Due to the high speed adjustment accuracy and fast response of the P1 motor, the input shaft is preferentially allocated to P1 for speed adjustment, that is, the torque intervention of P1.

The strategy for emission reduction in the P2.5 hybrid system involves the optimization of engine torque, engine speed, catalyst heat duration, and motor torque regulation in a coordinated manner. In addition to employing traditional engine control methods used in HEV models, unique approaches can be utilized to effectively manage emissions. The primary principle is to ensure that the engine operates predominantly under steady-state conditions or limits its load to regulate emissions levels. The main contributions of this paper are as follows: The first is the optimization of catalyst heating stage. During the catalyst heating stage, the system divides it into one or two stages. In the first stage, the vehicle is driven by the motor while keeping the engine idle. This approach stabilizes catalyst heating and prevents fluctuations in air-fuel ratio caused by speed and load changes that could potentially worsen emissions performance.

As the main power source of the electric vehicle, the electric motor has outstanding characteristics including rapid response, accurate control and four-quadrant operation. Being introduced into the dynamic chassis control of electrified vehicles, the electric motor torque can be used not only for driving and regenerative braking during normal operating conditions, but also offers a great potential to improve the dynamic control performance of the anti-lock braking under emergency deceleration situations. This paper presents a robust control algorithm for anti-lock braking of a front-wheel-drive electric vehicle equipped with an axle motor. The hydraulic and regenerative braking system of the electric vehicle is modeled as a LPV (linear parameter varying) system. The nonlinearities of the control system are considered as uncertain parameters of a linear fractional transformation.