Search Results

In a diesel engine, the mixing of the fuel spray and in-cylinder air controls rate of beat release during combustion, namely it will determine the thermal efficiency, maximum output and gas or noise emission, etc. Therefore, it is important to measure the droplet size and its volume density distribution in diesel fuel sprays. The optical measuring method, which includes a light scattering and holographic technique, seems the only feasible method for analysing these unsteady characteristics of fuel sprays. The light scattering technique described herein was based upon Mie scattering theory, and the droplet size and volume density distribution of fuel sprays were calculated from the combination of the light extinction and the forward-to-backscattering ratio of Mie scattering intensity. The volume density and droplet size distribution of fuel sprays were obtained from the light intensity distribution on a photograph of fuel sprays.

When the power or specific fuel consumption is estimated in design process, thermodynamic consideration for the estimation is generally insufficient. Hence, a theory that can estimate these performances accurately is investigated in this paper. As a result of investigation, it is clear that the effect of pumping loss in wide-opene throttle valve operation has to be excluded from the mechanical loss which is measured in the motoring test. It also becomes clear that a new coefficient called pumping loss coefficient ηP has to be considered for the negative work for pumping. From the foregoing, theoretical formulas for estimating the net power Pe and net specific fuel consumption be. which are formed with various efficiencies and coefficients are as follows: It is verified that the estimation from these formulas agree well with the experimental test values using stoichiometric mixture ratio.

Described here is the tuning of the combustion systems of a precombustion chamber diesel engine for lower level of exhaust gas emission. The key points of the tuning are the decrease of the prechamber volume, the selection of the combustion chamber configuration, the injection nozzle characteristics and the optimum injection timing. It was made clear, in the results of investigation, that the degradation of lubricating oil and the cavitation pitting on the outer wall of cylinder liner were directly concerned with the combustion characteristics of low emission systems. And both problems have been solved. The result of combustion tuning of the engine shows less than 5 g/hp-h of NOx + HC with CARB 13 mode test cycle without deterioration of performance nor durability.

Described herein is the tuning of the combustion system of a direct injection type diesel engine to obtain low emission level and better fuel economy. Though the most important method of emission control for a direct injection system is considered to be timing retardation, it brings a higher level of smoke density and fuel consumption. In order to remove these faults, the authors developed a new combustion system based on a newly designed intake port which provides a favorable local mixing of fuel droplets and air in the combustion chamber for ignition by means of air turbulence. This new combustion system was analyzed with high speed photographs which were taken from the underside of the piston to enable observing the whole combustion chamber. Favorable characteristics of ignition and burning pattern of the new system were recognized by this analysis.

A new concept for diesel combustion was investigated by means of numerical simulation, engine experiment, and combustion observation in order to realize a simultaneous reduction of NOx and particulate emission. This concept (HiMICS: Homogeneous charge intelligent Multiple Injection Combustion System) is based on pre-mixed compression ignition combustion combined with multiple injection. Combustion characteristics of HiMICS concept was investigated by comparing with both a standard single injection and a pilot injection. In HiMICS concept, the pre-mixture is formed by a preliminary injection performed during a period from the early stage of the induction stroke to the middle stage of the compression stroke. Modified KIVA-II code was used to predict engine performances and emissions of each injection method. The simulation results show a capability of considerable improvement in the trade-off relation between NOx emissions and fuel consumption of HiMICS.

Radio noise generated by the ignition system of internal combustion engines is primarily caused by the capacitive discharge current flowing in the ignition circuit when the spark occurs at spark gap. It is known that suppression of the capacitive discharge current usually effective in reducing the radiated ignition noise level. [1]* However, with exposed engines such as outboard marine, motorcycles, and particularly, in devices with long metal bodies, the radiated level peaks at a frequency which is determined by the length of the metal body. The authors found that the phenomenon described above could be explained by assuming electrostatic induction current. This was based on the noise voltage from the ignition system to the device. This paper intends to report the findings of this research.

This paper represents the adaptation of turbo charger to single cylinder 450cc SI engine which is used for the student formula competition. The experiment and 1D engine simulation called as GT-Power were performed to confirm the effect of valve profile, compression ratio and air fuel ratio on the engine performance under the naturally aspirated condition. The maximum valve lift of the intake valves increased 27% and that of the exhaust valves increased 15% as compared with the low profile cam. The compression ratio was increased from 12.3 to 13.5 by changing the piston top land length in order to improve the thermal efficiency. It was confirmed that the torque peak was moved from 6000 rpm to 8000 rpm by changing the valve profile. Furthermore, turbo charger was adapted to the engine as changing the capacity of the turbocharger, the maximum boost pressure and the air fuel ratio.

1 Many environmental problems, such as global warming, drain of fuel and so on, are apprehended in all over the world today, and down-sizing is one of the wise ways to deal with these problems. It is significant that a decrease of the engine power must not be produced by using a small displacement engine, so more efficient engine system should be designed to increase the torque with a little fuel. This study achieves an improvement of efficiency for mounting the super charging system on the small displacement engine. As a result, comparing a super charged engine and a naturally aspirated one to drive the same course and laps, fuel consumptions are 2547 [cc] and 3880 [cc], respectively, and an improvement of fuel consumption is 52%. Designing points to mount super charging system is introduced below. 1 It can be forecasted that intake air blow-by gas at the combustion chamber is increased in low engine speed because engine for motor cycle is used.

A current unmodified and modified engines with different amounts of thermal insulation have been used to generate data from which changes in bsfc, cooling loss, emissions, exhaust loss were determined. Since legislative requirement exists for allowable emission of NOx, fuel injection timing and other controllable factors were adjusted to maintain constant NOx emission except a test of influence on NOx emission according to the rate of heat insulation (adiabaticity). The effect of higher combustion temperature on the combustion phenomena is discussed.

The experiments were done in order to obtain the fundamental information that would be needed to build a physical model which expresses the heat transfer phenomena in the intake port model and manifold. In the experiments, the heating conditions and the period of the cyclic change of the gas velocity were changed as experimental parameters. In addition to those parameters, the Strouhal number was applied to express oscillating flow. As a result, the heat transfer in the experiments became clear, and the equations were obtained to show the Nusselt number using the Reynolds number, the Graetz number and the Strouhal number.

Cu-Pb alloy bearings were collected from diesel engines actually operated in the United States and Japan, and a study was made of the damage to bearing overlays and linings. Results indicated exposure of compound layers produced by the diffusion of overlay components due to the complete removal of overlay from large segments of the bearing inner surface. There were many bearings in which the Pb had been last from the Cu-Pb alloy. Based on the above results, experiments were conducted in which a tester was used to recreate the damage conditions of the overlay and the lining. Then, based on observation and the results of regenerative tests, it was concluded that high temperatures and lubricating oil used over a long period had a great impact on damage.

Historically the high speed diesel engine for commercial vehicles has been developed along with its combustion system in compliance with political and economical changes. After the 1970's, stricter exhaust emission regulations and fuel economy requirements induced combustion developments and application of turbocharged and inter cooled engines. From the late 1980's, high pressure fuel injection has been investigated and recognized as an essential tool for lowering emissions especially of particulate matter. Although turbulence effects on both in-cylinder air motion and during the combustion process are quite effective, they show different phenomena in conventional and advanced high pressure fuel injection systems. In the 1990's, multiple injection with high pressure has been attempted for further reduction of NOx and particulate matter.

A historical review of Japanese turbocharged diesel engines for heavy duty vehicles is described, and newly developed turbocharged diesel engines of HINO are introduced. The design features of these engines include new turbocharging technologies such as highly backward curved impeller for compressor blade, variable controlled inertia charging and waste gate. Laboratory and field test results demonstrated better fuel economy and improved low speed and transient torque characteristics than the predecessors. Several operational experiences, technical analysis and reliability problems are discussed.

This paper presents technical solutions and a development process to accomplish not only superior fuel economy but also excellent driveability with a turbocharged diesel engine for heavy duty trucks. For better fuel economy, one of the basic considerations is how to decrease the friction losses of the engine itself while keeping the required horsepower and torque characteristics. A high boost turbocharged small engine offers this possibility, but it has serious disadvantages such as inferior low speed torque, poorer accelerating response, insufficient engine braking performance, and finally not always so good fuel consumption in the engine operating range away from the matching point between engine and turbocharger. These are not acceptable in complicated traffic conditions like those in Japan - a mixture of mountainous and hilly roads, city road with numerous traffic signals, and freeways.

Attribute to high heat transfer rate and less complexity, the Helical coil sub-cooled condenser (HCSCC) can provide the most innovative and unique application for the air conditioning system. In the case of automobiles, reduction in air-conditioning load may diminish the vehicular emission, and power consumption as the air-conditioning load is the most power-consuming components after the engine load. Moreover, to solve the problem, we focus on the helical type heat exchanger. It may play a vital role in reducing the weight and increase the performance of the small engine because of the compact structure and lighter weight. The compressor unit is the most vital component of the refrigeration cycle, but the condenser unit is also one of the most critical devices, and the author tried to reduce the power consumption by enhancing the performance of the condenser.

Diesel engines need to optimize the fuel injection timing and quantity of each cycle in the transient operation to increase the thermal efficiency and reduce the exhaust gas emissions through the precise combustion control. The heat transfer from the working gas in the combustion chamber to the chamber wall is a crucial factor to predict the gas temperature in the combustion chamber to optimize the timing and quantity of fuel injection. Therefore, the authors developed both the heat loss and the polytropic index prediction models with the low calculation load and high accuracy. In addition, for the calculation of the heat loss and the polytropic index, the wall heat transfer model was also developed, which was derived from the continuity equation and the energy equation. The present study used a single cylinder diesel engine under the condition of engine speed of 1200 and 1500 rpm, and measured the local wall temperature and the local heat flux of the combustion chamber.

This investigation was concerned with the rate of heat transfer from the working gases to the combustion chamber walls of the internal combustion engines. The numerical formula for estimating the heat transfer to the combustion chamber wall was derived from the theoretical analysis and the experiment, which were used the constant volume combustion chamber and the actual gasoline engine. As a result, mean heat transfer in the internal combustion engine becomes possible to estimate with measuring the cylinder pressure. In addition, the derived numerical formula forms with quite simple variables. Therefore it is very useful for engine design.

For further development of the thermal efficiency of SI engines, the robust control of the air-fuel ratio (A/F) fluctuation is one of the most important technologies, because the A/F is maintained at the theoretical constant value, which causes the increase of the catalytic conversion efficiency and the reduction of pollutant emission. We developed the robust controller of the A/F, which is the method to change the fuel injection rate by using the feed-forward (FF) controller considering the heat transfer at the intake system. The FF controller was verified under transient driving conditions for a single cylinder, and the A/F fluctuations were reduced at approximately 84%.

Measuring precise cylinder pressure traces of internal combustion engines is an important factor for estimating their performances. It is known that the actual pressure readings measured with piezoelectric pressure transducers nave various forms of error. This paper is devoted to a study of compensation methods for reducing the errors caused by time constant values and thermal shock. Numerical analysis were carried out for the both errors to derive the equations of error compensation using the actual pressure data. The results indicate that the errors are corrected quite well with the obtained equations.

In order to get better results in the Formula SAE of Japan, it is necessary to develop a small displacement engine with an ideal fuel consumption rate. Therefore, the authors started to improve an existing engine by combining with glow plug heated sub-chamber and lean burn. Lean burn conditions are usually adopted in gasoline engines, having the advantages of high specific heat ratio, low pump loss, and low cooling loss due to requiring a decreased combustion temperature. The combination of these elements can be expected to vastly improve thermal efficiency and fuel consumption. Unfortunately, however, when the mixture becomes lean, the ignition delay increases, and the flame propagation speed reduces. This leads to an increase in combustion fluctuation. The authors intend to solve this problem by installing a glow plug in a newly designed sub-chamber. This type of device would usually be used to heat the sub-chamber of a diesel engine to solve the cold start problem.