Search Results

It has been long established fact that fuel economy is a key driving force of low viscosity gasoline engine oil research and development considered by the original equipment manufacturers (OEMs) and lubricant companies. The development of low viscosity gasoline engine oils should not only focus on fuel economy improvement, but also on the low speed pre-ignition (LSPI) prevention property. In previous LSPI prevention literatures, the necessity of applying Ca/Mg-based detergents system in the engine oil formulations was proposed. In this paper, we adopted a specific Group III base oil containing Ca-salicylate detergent, borated dispersant, Mo-DTC in the formulation and investigated the various effects of Mg-salicylate and Mg-sulfonate on the performance of engine oil. It was found that Mg-sulfonate showed a significant detrimental impact on silicone rubber compatibility while the influence from Mg-salicylate remains acceptable.

Described here is the tuning of the combustion systems of a precombustion chamber diesel engine for lower level of exhaust gas emission. The key points of the tuning are the decrease of the prechamber volume, the selection of the combustion chamber configuration, the injection nozzle characteristics and the optimum injection timing. It was made clear, in the results of investigation, that the degradation of lubricating oil and the cavitation pitting on the outer wall of cylinder liner were directly concerned with the combustion characteristics of low emission systems. And both problems have been solved. The result of combustion tuning of the engine shows less than 5 g/hp-h of NOx + HC with CARB 13 mode test cycle without deterioration of performance nor durability.

Described herein is the tuning of the combustion system of a direct injection type diesel engine to obtain low emission level and better fuel economy. Though the most important method of emission control for a direct injection system is considered to be timing retardation, it brings a higher level of smoke density and fuel consumption. In order to remove these faults, the authors developed a new combustion system based on a newly designed intake port which provides a favorable local mixing of fuel droplets and air in the combustion chamber for ignition by means of air turbulence. This new combustion system was analyzed with high speed photographs which were taken from the underside of the piston to enable observing the whole combustion chamber. Favorable characteristics of ignition and burning pattern of the new system were recognized by this analysis.

Radio noise generated by the ignition system of internal combustion engines is primarily caused by the capacitive discharge current flowing in the ignition circuit when the spark occurs at spark gap. It is known that suppression of the capacitive discharge current usually effective in reducing the radiated ignition noise level. [1]* However, with exposed engines such as outboard marine, motorcycles, and particularly, in devices with long metal bodies, the radiated level peaks at a frequency which is determined by the length of the metal body. The authors found that the phenomenon described above could be explained by assuming electrostatic induction current. This was based on the noise voltage from the ignition system to the device. This paper intends to report the findings of this research.

This paper represents the adaptation of turbo charger to single cylinder 450cc SI engine which is used for the student formula competition. The experiment and 1D engine simulation called as GT-Power were performed to confirm the effect of valve profile, compression ratio and air fuel ratio on the engine performance under the naturally aspirated condition. The maximum valve lift of the intake valves increased 27% and that of the exhaust valves increased 15% as compared with the low profile cam. The compression ratio was increased from 12.3 to 13.5 by changing the piston top land length in order to improve the thermal efficiency. It was confirmed that the torque peak was moved from 6000 rpm to 8000 rpm by changing the valve profile. Furthermore, turbo charger was adapted to the engine as changing the capacity of the turbocharger, the maximum boost pressure and the air fuel ratio.

1 Many environmental problems, such as global warming, drain of fuel and so on, are apprehended in all over the world today, and down-sizing is one of the wise ways to deal with these problems. It is significant that a decrease of the engine power must not be produced by using a small displacement engine, so more efficient engine system should be designed to increase the torque with a little fuel. This study achieves an improvement of efficiency for mounting the super charging system on the small displacement engine. As a result, comparing a super charged engine and a naturally aspirated one to drive the same course and laps, fuel consumptions are 2547 [cc] and 3880 [cc], respectively, and an improvement of fuel consumption is 52%. Designing points to mount super charging system is introduced below. 1 It can be forecasted that intake air blow-by gas at the combustion chamber is increased in low engine speed because engine for motor cycle is used.

The experiments were done in order to obtain the fundamental information that would be needed to build a physical model which expresses the heat transfer phenomena in the intake port model and manifold. In the experiments, the heating conditions and the period of the cyclic change of the gas velocity were changed as experimental parameters. In addition to those parameters, the Strouhal number was applied to express oscillating flow. As a result, the heat transfer in the experiments became clear, and the equations were obtained to show the Nusselt number using the Reynolds number, the Graetz number and the Strouhal number.

Fuel economy measurement test is one of important engine tests to establish fuel economy engine oil performance standard to support CO2 emission reduction efforts in the automotive industry. On the other hand, it is difficult to develop an engine test without appropriate engine hardware that is designed to utilize low viscosity engine oils. A new firing fuel economy test was developed based on 2ZR-FXE engine designed for hybrid powertrain. The new test procedure aimed to provide the tool to evaluate new low viscosity grades such as 0W-8 and 0W-12 that were adapted in SAE J300 in 2015.

A historical review of Japanese turbocharged diesel engines for heavy duty vehicles is described, and newly developed turbocharged diesel engines of HINO are introduced. The design features of these engines include new turbocharging technologies such as highly backward curved impeller for compressor blade, variable controlled inertia charging and waste gate. Laboratory and field test results demonstrated better fuel economy and improved low speed and transient torque characteristics than the predecessors. Several operational experiences, technical analysis and reliability problems are discussed.

It is important to reduce the viscosity of automatic transmission fluid (ATF) in order to improve fuel economy. However, in general, low viscosity fluid can cause metal fatigue, wear, and seizure. It is necessary to increase the viscosity of the fluid at higher temperatures to maintain the durability of the automatic transmission (AT). The key point is the selection of the base oil and the viscosity index improver (VII) with both a high viscosity index (VI) and excellent shear stability. On the basis of this concept, a new generation high performance ATF named WS was developed. WS can achieve the highest level of fuel economy, while maintaining the durability of the AT.

We developed a new Manual Transmission Gear Oil (MTF) named LV for improved fuel economy and CO2 reduction. MTF LV is a low viscosity fluid to reduce stir losses at lower temperatures. In general, low viscosity fluids can cause metal fatigue, wear and seizure. The MTF LV was designed to overcome these problems by maintaining the oil film thickness after it is deteriorated and improving the wear characteristics with additives. As a result, the MTF LV provides equal or better durability than the current MTF. In addition, it also has good performance at low temperatures, better shift feeling characteristics, and improved oxidation stability.

Further fuel economy improvement of the internal combustion engine is indispensable for CO2 reduction in order to cope with serious global environmental problems. Although lowering the viscosity of engine oil is an effective way to improve fuel economy, it may reduce the wear resistance. Therefore, it is important to achieve both improved fuel economy and reliability. We have developed new 0W- 8 engine oil of ultra-low viscosity and achieved an improvement in fuel economy by 0.8% compared to the commercial 0W-16 engine oil. For this new oil, we reduced the friction coefficient under boundary lubrication regime by applying an oil film former and calcium borate detergent. The film former increased the oil film thickness without increasing the oil viscosity. The calcium borate detergent enhanced the friction reduction effect of molybdenum dithiocarbamate (MoDTC).

This paper presents technical solutions and a development process to accomplish not only superior fuel economy but also excellent driveability with a turbocharged diesel engine for heavy duty trucks. For better fuel economy, one of the basic considerations is how to decrease the friction losses of the engine itself while keeping the required horsepower and torque characteristics. A high boost turbocharged small engine offers this possibility, but it has serious disadvantages such as inferior low speed torque, poorer accelerating response, insufficient engine braking performance, and finally not always so good fuel consumption in the engine operating range away from the matching point between engine and turbocharger. These are not acceptable in complicated traffic conditions like those in Japan - a mixture of mountainous and hilly roads, city road with numerous traffic signals, and freeways.

Diesel engines need to optimize the fuel injection timing and quantity of each cycle in the transient operation to increase the thermal efficiency and reduce the exhaust gas emissions through the precise combustion control. The heat transfer from the working gas in the combustion chamber to the chamber wall is a crucial factor to predict the gas temperature in the combustion chamber to optimize the timing and quantity of fuel injection. Therefore, the authors developed both the heat loss and the polytropic index prediction models with the low calculation load and high accuracy. In addition, for the calculation of the heat loss and the polytropic index, the wall heat transfer model was also developed, which was derived from the continuity equation and the energy equation. The present study used a single cylinder diesel engine under the condition of engine speed of 1200 and 1500 rpm, and measured the local wall temperature and the local heat flux of the combustion chamber.

Increasing numbers of vehicles equipped with downsized, turbocharged engines have been introduced seeking for better fuel economy. LSPI (low speed pre-ignition), which can damage engine hardware, is a potential risk of the engines. We reported that engine oil formulation affects frequency of LSPI events, and formulating magnesium detergents into oil is a promising option to prevent LSPI events. From the viewpoint of achieving better fuel economy by engine oil, lowering viscosity is being required. However, it causes reduced oil film thickness and will expand boundary lubrication condition regions in some engine parts. Hence, a technology to reduce friction under boundary lubrication becomes important.

With the electrification of automobiles, such as hybridization, engines on these vehicles operate more frequently at low oil temperatures, while engines are more specifically run at low engine speed and high load condition for driving vehicles. Hence, engine oils are required to reduce their viscosity at low temperature for friction reduction to improve fuel economy and maintain high temperature viscosity enough to protect engine parts for robustness at the same time. This leads to the improvement of viscosity index, the "ultra-high viscosity index (UHVI)" concept. The novel engine oil technology with a new high performance polymer was investigated. One of experimental oils showed the 100°C viscosity equivalent to SAE 0W-16 grade and the better fuel economy than that of SAE 0W-8 oil by an engine motoring friction test.

This investigation was concerned with the rate of heat transfer from the working gases to the combustion chamber walls of the internal combustion engines. The numerical formula for estimating the heat transfer to the combustion chamber wall was derived from the theoretical analysis and the experiment, which were used the constant volume combustion chamber and the actual gasoline engine. As a result, mean heat transfer in the internal combustion engine becomes possible to estimate with measuring the cylinder pressure. In addition, the derived numerical formula forms with quite simple variables. Therefore it is very useful for engine design.

For further development of the thermal efficiency of SI engines, the robust control of the air-fuel ratio (A/F) fluctuation is one of the most important technologies, because the A/F is maintained at the theoretical constant value, which causes the increase of the catalytic conversion efficiency and the reduction of pollutant emission. We developed the robust controller of the A/F, which is the method to change the fuel injection rate by using the feed-forward (FF) controller considering the heat transfer at the intake system. The FF controller was verified under transient driving conditions for a single cylinder, and the A/F fluctuations were reduced at approximately 84%.

Measuring precise cylinder pressure traces of internal combustion engines is an important factor for estimating their performances. It is known that the actual pressure readings measured with piezoelectric pressure transducers nave various forms of error. This paper is devoted to a study of compensation methods for reducing the errors caused by time constant values and thermal shock. Numerical analysis were carried out for the both errors to derive the equations of error compensation using the actual pressure data. The results indicate that the errors are corrected quite well with the obtained equations.

In order to get better results in the Formula SAE of Japan, it is necessary to develop a small displacement engine with an ideal fuel consumption rate. Therefore, the authors started to improve an existing engine by combining with glow plug heated sub-chamber and lean burn. Lean burn conditions are usually adopted in gasoline engines, having the advantages of high specific heat ratio, low pump loss, and low cooling loss due to requiring a decreased combustion temperature. The combination of these elements can be expected to vastly improve thermal efficiency and fuel consumption. Unfortunately, however, when the mixture becomes lean, the ignition delay increases, and the flame propagation speed reduces. This leads to an increase in combustion fluctuation. The authors intend to solve this problem by installing a glow plug in a newly designed sub-chamber. This type of device would usually be used to heat the sub-chamber of a diesel engine to solve the cold start problem.