Search Results

This paper describes a methodology for design and development of On-Board Diagnostic system (OBD) with an objective to improve current reliability process in order to ensure design & quality of the new system as per requirement of commercial vehicle technology. OBD is a system that detects failures which adversely affect emissions and illuminates a MIL (Malfunction Indicator Lamp) to inform the driver of a fault which may lead to increase in emissions. OBD provides standard and unrestricted access for diagnosis and repair. Below given Figure 1 shows the working principle of OBD system. The exhaust emission of a vehicle will be controlled primarily by Engine Control Unit (ECU) and Exhaust Gas After Treatment Control (EGAS CU). These two control units determine the combined operating strategies of the engine and after treatment device. Figure 1 Modern Control Architecture for OBD System in Commercial vehicle [1]

Diesel engine pollutants include Oxides of Nitrogen (NOx) and Particulate Matter (PM) which are traditionally known for their trade-off characteristics. It’s been a challenge to reduce both pollutants at the source simultaneously, except by efforts through low temperature combustion concepts. NOx formation is dependent on the combustion temperature and thus the in-cylinder reduction of NOx formation remains of utmost importance. In this regard, water injection into the intake of a heavy-duty diesel engine to reduce peak combustion temperature and thereby reducing NOx is found to be a promising technology. Current work involves the use of 1-D thermodynamic simulation using AVL BOOST for modeling the engine performance with water injection. Mixing Controlled Combustion (MCC) model was used which can model the emissions. Initially, the model validation without the water injector was carried out with experimental data.

Oil strainer is used in engine oil sump, which prevents dirt, scale and other particle from clogging downstream orifice. In this paper, dynamic analysis was carried out using FEA tool. As a part of dynamic analysis, constrained modal analysis and frequency response (steady state dynamics) analysis was done. Frequency response analysis was done for different engine exciting frequency at different service load (vibration amplitude). Modal superposition method is used for doing frequency response analysis and load is applied as base excitation. The natural frequency from modal analysis and stress response from frequency response analysis is well correlated with test results. Based on achieved good correlation with test, several design modification could be carried out in CAE before finalizing the final design.

Automotive industry is progressively embracing newer technology for buses, as they are increasingly becoming the backbone of urban transportation. Buses are generally classified based on floor heights, lengths, seating capacity and applications besides lot of other parameters. Generally low floor / low entry buses are used for city transportation, while high floor / high deck buses are used for inter urban and intercity transportation. Yet in a few developing and underdeveloped geographies across the globe, high deck or the semi low floor buses are still used for city/urban transportation. There could be a lot of reasons like infrastructure limitations, the cost of ownership or in some cases even the topology of these geographies could be unfriendly towards low floor buses and low ground clearances. Varying customer requirements, applications and environmental factors necessitates a broad range of offerings from any bus OEM.

There have always been different approaches when it comes to ‘Bus body architecture’. The design approach has gone through different phases namely, chassis based, semi integral, integral and monocoque. Equally varied is the choice of material for bus super structure. The predominantly used ones are - mild steel with galvanization, stainless steel (SS) and aluminum. This paper discusses the rationale behind choosing stainless steel for the complete bus structure. With rapid development in infrastructure and public mass transit system, it has become imperative to have a robust structure for buses that is durable and crash worthy. Among the family of stainless steels, ferritic stainless steel exhibits excellent mechanical properties with corrosion resistance and better strength to weight ratio compared to the galvanized mild steel.

In today’s world, due to fast depletion of fossil fuel and the increasing CO2 emission, the need to switch to alternate energy sources are higher. Stringent norms on exhaust emissions in IC Engine vehicles implies, very complex after treatment systems. Already many OEMs have refined their development strategies towards phasing out of IC Engines and bringing in Fuel Cell vehicles, Battery Electric Vehicles and Hydrogen IC Engine vehicles. Focus is on Hydrogen for Long Haul vehicles. In this paper cooling system design is demonstrated for Fuel Cell, Battery and Power Electronics system in a Heavy Duty Fuel Cell Electric Truck. Radiator and Fans are selected based on the overall heat rejection and Coolant inlet temperature requirements of components. Cooling system circuit and pump is decided to meet the coolant flow rate targets. High temperature cooling system and Low temperature cooling system are explained in detail. Thermal simulation is done using simulation software KULI.