Search Results

There is a need for reducing fuel consumption and thereby also reducing CO2 and other emissions in all areas of transportation and the forest industry is no exception. In the particular case of timber trucks special care have to be taken when designing such vehicles; they have to be sturdy and operate in harsh conditions and they are being driven empty half the time. It is well known that the aerodynamic resistance constitutes a significant part of the vehicles driving resistance and four areas in particular, front of vehicle, gap, side/underbody and rear of the vehicle contributes about one quarter each. In order to address these issues a wind tunnel investigation was initiated where a 1:6 scale model of a timber truck was designed to operate in a 3.6 m wind tunnel. The present model resembles a generic timber truck with a flexible design such that different configurations could be tested easily.

The possibility of non-volatile particle agglomeration in engine exhaust was experimentally examined in a Euro VI heavy duty engine using a variable cross section agglomeration pipe, insulated and double walled for minimal thermophoresis. The agglomeration pipe was located between the turbocharger and the exhaust treatment devices. Sampling was made across the pipe and along the centre-line of the agglomeration pipe. The performance of the agglomeration pipe was compared with an equivalent insulated straight pipe. The non-volatile total particle number and size distribution were investigated. Particle number measurements were conducted according to the guidelines from the Particle Measurement Programme. The Engine was fuelled with commercially available low sulphur S10 diesel.

In the last couple of decades, countries have enacted new laws concerning environmental pollution caused by heavy-duty commercial and passenger vehicles. This is done mainly in an effort to reduce smog and health impacts caused by the different pollutions. One of the legislated pollutions, among a wide range of regulated pollutions, is nitrogen oxides (commonly abbreviated as NOx). The SCR (Selective Catalytic Reduction) was introduced in the automotive industry to reduce NOx emissions leaving the vehicle. The basic idea is to inject a urea solution (AdBlue™) in the exhaust gas before the gas enters the catalyst. The optimal working temperature for the catalyst is somewhere in the range of 300 to 400 °C. For the reactions to occur without a catalyst, the gas temperature has to be at least 800 °C. These temperatures only occur in the engine cylinder itself, during and after the combustion.

When applying high amount of EGR (exhaust gas recirculation) in Partially Premixed Combustion (PPC) using diesel fuel, an increase in soot emission is observed as a penalty. To better understand how EGR affects soot particles in the cylinder, a fast gas sampling technique was used to draw gas samples directly out of the combustion chamber in a Scania D13 heavy duty diesel engine. The samples were characterized on-line using a scanning mobility particle sizer for soot size distributions and an aethalometer for black carbon (soot) mass concentrations. Three EGR rates, 0%, 56% and 64% were applied in the study. It was found that EGR reduces both the soot formation rate and the soot oxidation rate, due to lower flame temperature and a lower availability of oxidizing agents. With higher EGR rates, the peak soot mass concentration decreased. However, the oxidation rate was reduced even more.

The introduction of renewable alcohols as fuels for heavy-duty engines may play a relevant role for the reduction of the carbon footprint of the transport sector. The direct injection of ethanol as main fuel and diesel as pilot fuel in the engine combustion chamber through two separate injectors may allow good combustion controllability over the entire engine operating range by targeting diffusive combustion. Closed-cycle combustion simulations have been carried out using AVL FIRE coupled to AVL TABKIN for the implementation of the Flamelet Generated Manifold (FGM) chemistry reduction technique in order to investigate the influence of the injection system geometry and the injection strategy of pure ethanol and diesel fuel on ignition characteristics and combustion at different operating conditions.

Diffusive combustion of direct injected ethanol is investigated in a heavy-duty single cylinder engine for a broad range of operating conditions. Ethanol has a high potential as fossil fuel alternative, as it provides a better carbon footprint and has more sustainable production pathways. The introduction of ethanol as fuel for heavy-duty compression-ignition engines can contribute to decarbonize the transport sector within a short time frame. Given the resistance to autoignition of ethanol, the engine is equipped with two injectors mounted in the same combustion chamber, allowing the simultaneous and independent actuation of the main injection of pure ethanol and a pilot injection of diesel as an ignition source. The influence of the dual-fuel injection strategy on ethanol ignition, combustion characteristics, engine performance and NOx emissions is evaluated by varying the start of injection of both fuels and the ethanol-diesel ratio.

When a truck or bus suffers from a breakdown it is important that the vehicle comes back on the road as soon as possible. In this paper we present a prototype diagnostic decision support system capable of automatically identifying possible causes of a failure and propose recommended actions on how to get the vehicle back on the road as cost efficiently as possible. This troubleshooting system is novel in the way it integrates the remote diagnosis with the workshop diagnosis when providing recommendations. To achieve this integration, a novel planning algorithm has been developed that enables the troubleshooting system to guide the different users (driver, help-desk operator, and mechanic) through the entire troubleshooting process. In this paper we formulate the problem of integrated remote and workshop troubleshooting and present a working prototype that has been implemented to demonstrate all parts of the troubleshooting system.

Diesel engine manufacturers strive towards further efficiency improvements. Thus, reducing in-cylinder heat losses is becoming increasingly important. Understanding how location, thermal insulation, and engine operating conditions affect the heat transfer to the combustion chamber walls is fundamental for the future reduction of in-cylinder heat losses. This study investigates the effect of a 1mm-thick plasma-sprayed yttria-stabilized zirconia (YSZ) coating on a piston. Such a coated piston and a similar steel piston are compared to each other based on experimental data for the heat release, the heat transfer rate to the oil in the piston cooling gallery, the local instantaneous surface temperature, and the local instantaneous surface heat flux. The surface temperature was measured for different crank angle positions using phosphor thermometry.

Increasing demands for more efficient engines and stricter legislations on exhaust emissions require more accurate control of the engine operating parameters. Engine control is based on sensors monitoring the condition of the engine. Numerous sensors, in a complex control context, increase the complexity, the fragility and the cost of the system. An alternative to physical sensors are virtual sensors, observers used to monitor parameters of the engine thus reducing both the fragility and the production cost but with a slight increase of the complexity. In the current paper a virtual intake manifold cylinder port pressure sensor is presented. The virtual sensor is based on a compressible flow model and on the pressure signal of the intake manifold pressure sensor. It uses the linearized pressure coefficient approach to keep vital performance behaviors while still conserving calibration effort and embedded system memory.

Traditionally, an in-vehicle map consists of only one type of data, tailored for a single user function. For example, the navigation maps contain spatial information about the roads. On the other hand, a map built for adaptive cruise control use consists of the detected vehicles and their properties. In autonomous vehicle research, the maps are often built up as an occupancy grid where areas are classified as passable or impassable. Using these kinds of maps separately, however, is not enough to support the traffic safety enhancing and advanced driver assistance systems of today and tomorrow. Instead of using separate systems to handle individual safety or planning tasks, information could be stored in one shared map containing several correlated layers of information. Map information can be collected by any number of different sensor devices, and fusion algorithms can be used to enhance the quality of the information.

Maintenance planning of trucks at Scania have previously been done using static cyclic plans with fixed sets of maintenance tasks, determined by mileage, calendar time, and some data driven physical models. Flexible maintenance have improved the maintenance program with the addition of general data driven expert rules and the ability to move sub-sets of maintenance tasks between maintenance occasions. Meanwhile, successful modelling with machine learning on big data, automatic planning using constraint programming, and route optimization are hinting on the ability to achieve even higher fleet utilization by further improvements of the flexible maintenance. The maintenance program have therefore been partitioned into its smallest parts and formulated as individual constraint rules. The overall goal is to maximize the utilization of a fleet, i.e. maximize the ability to perform transport assignments, with respect to maintenance.

A turbocharged Diesel engine for heavy-duty on-road vehicle applications employs a compact exhaust manifold to satisfy transient torque and packaging requirements. The small exhaust manifold volume increases the unsteadiness of the flow to the turbine. The turbine therefore operates over a wider flow range, which is not optimal as radial turbines have narrow peak efficiency zone. This lower efficiency is compensated to some extent by the higher energy content of the unsteady exhaust flow compared to steady flow conditions. This paper experimentally investigates the relationship between exhaust energy utilization and available energy at the turbine inlet at different degrees of unsteady flow. A special exhaust manifold has been constructed which enables the internal volume of the manifold to be increased. The larger volume reduces the exhaust pulse amplitude and brings the operating condition for the turbine closer to steady-flow.