Search Results

In an electric vehicle, engine is replaced with battery and transmission is replaced with traction motor. Thermal management of electric battery and motor became a necessary evaluation step in the design and development process of electric vehicles. The temperature of the traction motor coolant is required to be maintained below 600C to ensure proper functioning of the system. Coolant takes away heat from traction motor, motor controller along with an on-board charger in battery charging and discharging conditions. In this paper the cooling unit selection for the total required heat rejection from all three components is analytically calculated and thermal management methodology of liquid-cooled Electric Motor is being studied and documented with the help of numerical simulation. The results are further validated with test results in Electric bus for city application.

An optimally functioning SLI (Starting Lighting and Ignition) battery is a primordial element in the unimpaired operation of an ICE vehicle. Designed to deliver the highest current momentarily during ignition, and not intended for deep discharge, these batteries have been observed to suffer from premature degradation, attributed to misuse and lack of maintenance. Focused on the cell chemistry, a wet-cell lead-acid battery’s degradation is initiated by the reduction of active electrode area through sulfation in each charge-discharge cycle. While the formation and dissolution of sulfate crystals is a normal phenomenon, in scenarios of deep discharge the formation and agglomeration of larger insoluble sulfate crystals reduce the cell capacity leading to overall poor reserve capacity and cold cranking ability of the battery.

An engine cooling system is required to maintain stable operating temperature for the engine and prevent it from overheating. Thermal distortion of engine parts can take place if proper cooling is not maintained and engine may loss efficiency. One of the major problem in this domain is to incorporate separate cooling systems for the different variants of engines (different power rating). A single optimized cooling unit is desired to manage the entire range of engine rated power. The factors that affect the cooling system are front end grill opening area, air recirculation, location of snorkel inlet, radiator core size, which need to be tuned to get appropriate results. The above parameters are tuned to obtain appropriate results using the Computational Fluid Dynamics (CFD) simulations. In the next stage, on road cooling trials are performed and real time data is collected.

The Advancement in Connected vehicles Technology in recent years has propelled the use of concepts like the Internet of Things (IoT) and big data in the automotive industry. The progressive electrification of the powertrain has led to the integration of various sensors in the vehicle. The data generated by these sensors are continuously streamed through a telematics device on the vehicle. Data analytics of this data can lead to a variety of applications. Predictive maintenance is one such area where machine learning algorithms are applied to relevant data to predict failure. Field vehicle malfunction or breakdown is costly for manufacturers’ aftermarket services. In the case of commercial vehicles, downtime is the biggest concern for the customer. The use of predictive maintenance techniques can prevent many critical failures by tending to the root cause in the early stages of failure. Engine overheating is one such problem that transpires in diesel engines.

Diesel engines are facing stringent norms and future survival with its lower availability is one of the biggest concerns for OEMs of heavy duty commercial vehicles. This is leading to uplifting of new, latent and innovative techniques to achieve these norms with best possible BSFC to reduce overall diesel consumption. The prime objective of this study is to identify and explore the latent strength of pre and post injection on engine performance, emissions and oil dilution due to soot. The post injection strategy has the potential to reduce soot with almost same NOx and fuel consumption depending on the delay of post injection and its quantity. It aids to increase the engine out temperatures for assistance of after-treatment devices, thus meeting higher temperature requirements for NOx and PM conversion for stringent norms of BSVI.

Downsizing and Light weighting is the latest trend in the automotive industry to achieve more fuel efficient, compact and cost effective design of vehicles. Powertrain components compromise of more than 45% of the total vehicle weight. Automakers are putting significant efforts to reduce the weight of power train components. Integrated design of aluminum Engine Head and Intake manifold has been successfully implemented. Now currently we have identified the gear box housings for downsizing in light duty trucks i.e. Existing light duty trucks Cast Iron transmission. This design has been successfully modified with integrated clutch housing and transmission housing, using lightweight aluminum as the new material, using simulation tools. This lead to weight savings of up to 30% and cost savings of 20-25% as compared to existing cast iron designs. Using an integrated design reduces the assembly cost, makes the design more compact and gives better weight balance.

In order to stand apart from the competition, there is an ever growing demand in Indian commercial vehicle segments to reach higher fuel economy while achieving the emission goals set by the BS-VI norms. With emissions standard set by BS-VI, novel techniques to improve fuel efficiency have to be considered that have least impact with respect to NOx and soot emissions. The optimization of exhaust and intake valve lifts with respect to engine speed, technology commonly known as Variable Valve Lift and Timing (VVT/VVL), has been implemented in many passenger vehicles propelled by gasoline engine. The aim of this work is do initial assessment of utilizing the VVL method on a LMD commercial vehicle diesel engine. A 3.8 litre BS-VI turbocharged EGR engine is used for this study. Valve lift and timing optimization for better fuel efficiency at rated power engine speed is carried out by using one-dimensional thermodynamic simulation software AVL BOOST.

Engine down speeding is rapidly picking up momentum in many segment of world market. Numerous engine down speeding packages from OEM have been tailored to take advantage of the increased efficiencies associated with engine down speeding. Running engine at lower rpm has numerous advantages. The most obvious of these is reduced fuel consumption, since the engine can spend more time running within its optimum efficiency range. By down speeding, the engine is made to run at low speeds and with high torques. For the same power, the engine is operated at higher specific load- Brake Mean Effective pressure (BMEP) which results in higher efficiency and reduced fuel consumption-Brake Specific Fuel Consumption (BSFC). The reasons for increased fuel efficiency are reduced engine friction due to low piston speeds, reduced relative heat transfer and increased thermodynamic efficiency.

With implementation of stringent BSVI emission norms and regulations like OBD-II on vehicle, it is essential to define the life of exhaust after treatment along with the vehicle. Diesel after treatment generally consists of DOC, DPF and SCR. Lubricating oil contains phosphorus and zinc which adversely affect the DOC. Unburned hydrocarbons (UNHBC) and SOF in tail pipe get accumulated in the DPF. This requires regeneration process where in, high temperatures in exhaust after treatment (EATS) burn the adsorbed Sulphur or phosphorus, thereby improving the conversion efficiencies. Repeated regenerations lead to ash accumulation in DPF and this reduces its capability for soot accumulation. Sulphur in the exhaust impacts SCR through NOx conversion. The present study analyzes the effect of (1) Chemical aging (2) Thermal aging on 3.77 liter diesel engine after treatment. A test cycle was prepared to run the durability for EATS.

Air Pollution is a major concern in our country due to which Indian Government has taken a decision to move from BS-IV to BS-VI which is nearly 90% reduction in NOx and 50% in particulate matter along with addition of particulate number regulation for BS-VI in comparison to BS-IV norms in very short span of time. Vehicle manufacturers are also having the challenge to produce low cost and fuel efficient product with BS-VI solution in order to meet tightening emission regulations and increasing needs of lower fuel consumption. Detailed study is done with different approaches to meet BS-VI emission which is elaborately explained in different aspect of engine design and after treatment parameter with its pros and cons. After Treatment selection plays an important role in engine development to meet stringent emission legislations and customer demands. Strategies for BS-VI were described with the advantage and drawbacks for after treatment selection.

The intensifying demand of cleaner fuelled vehicles considering current norms of BSIV and upcoming stringent norms of BSVI with low cost solutions has promoted the development of CNG and dual fuel vehicles. CNG vehicle is anticipated to discover its extensive use for environment fortification and effective deployment of energy capitals. Thus, CNG vehicles can be pretty effective in averting environment deterioration. CNG has low carbon to hydrogen ratio, this leads to very low CO2 emissions compared to gasoline and diesel vehicles. CNG engines have the potential of low NOx and particulate emissions. Natural gas vehicle development has been directed on the way to current use of direct injection and port injection with S.I. engines. Generally for low cost development, all OEMs prefer optimization of existing engines. Similarly for this project, a diesel engine was converted to S.I. engine for development of low emission CNG engine.

In an automobile, main function of the steering system is to allow the driver to guide the vehicle on a desired course. Steering system consists of various components & linkages. Using these linkages, the torque from steering wheel is transferred to tyre which results in turning of the vehicle. Over the life of vehicle, these steering components are subjected to various loading conditions. As steering components are safety critical parts in the vehicle, therefore they should not fail while running because it will cause vehicle breakdown. In commercial vehicle segment, vehicle breakdown means delay in freight delivery which results in huge loss to costumer. Therefore, while designing steering components one should consider all the possible loadings condition those are possible. But, it can’t be done through theoretical calculation. Therefore, physical tests have to be carried out to validate design of steering system, which is very costly & time-consuming process.