Search Results

Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2018-04-15

HISTORICAL

J2691_201804

This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.

Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2020-02-25

CURRENT

J2691_202002

This SAE Standard establishes the minimum construction and performance requirements for a 15 pole connector between towing vehicles and trailers, for trucks, trailers, and dollies, for 12 VDC nominal applications in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.

Standard

A RECOMMENDED METHOD OF ANALYTICALLY DETERMINING THE COMPETENCE OF HYDRAULIC TELESCOPIC CANTILEVERED CRANE BOOMS

1994-04-05

HISTORICAL

J1078_199404

This analysis applies to crane types as covered by Power Crane and Shovel Association Standard Number Two, Mobile Hydraulic Crane Standards and ANSI B30.15; refer to 5.1.

Standard

A Recommended Method of Analytically Determining the Competence of Hydraulic Telescopic Cantilevered Crane Booms

1974-07-01

HISTORICAL

J1078_197407

This analysis applies to crane types as covered by Power crane and shovel Association Standard Number Two, Mobile Hydraulic Crane standards and ANSI B30.15; refer to 5.1. This calculation method has been established to illustrate an analysis to determine the competence of hydraulic telescopic cantilevered crane booms.

Standard

ACCELERATOR PEDAL POSITION SENSOR FOR USE WITH ELECTRONIC CONTROLS IN MEDIUM—AND HEAVY-DUTY VEHICLE APPLICATIONS

1993-04-01

HISTORICAL

J1843_199304

The purpose of this SAE Recommended Practice is to provide a common electrical and mechanical interface specification that can be used to design electronic accelerator pedal position sensors and electronic control systems for use in medium—and heavy-duty vehicle applications.

Standard

ACCESS SYSTEMS FOR CONSTRUCTION AND INDUSTRIAL EQUIPMENT

1970-07-01

HISTORICAL

J185_197007

This recommended practice covers the criteria for steps, ladders, walkways, platforms, grab rails (handrails), grab irons, guardrails, and entrance openings as they relate to aiding the operator and/or servicemen in performing their functions on the vehicle.

Standard

ACCESS SYSTEMS FOR OFF-ROAD MACHINES

1985-08-01

HISTORICAL

J185_198508

Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, or service platforms on off-road work machines parked in accordance with the manufacturer's instructions.

Standard

ACCESS SYSTEMS FOR OFF-ROAD MACHINES

1988-06-01

HISTORICAL

J185_198806

Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, maintenance or service platforms on off-road work machines parked in accordance with the manufacturer's instructions.

Standard

ACCESS SYSTEMS FOR OFF-ROAD MACHINES

1981-06-01

HISTORICAL

J185_198106

Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, or service platform on off-road work machines parked in accordance with the manufacturer’s instructions.

Standard

AGRICULTURAL TRACTOR TEST CODE

1972-06-01

HISTORICAL

J708C_197206

Standard

AGRICULTURAL TRACTOR TEST CODE

1980-06-01

HISTORICAL

J708_198006

Standard

AGRICULTURAL TRACTOR TEST CODE

1983-07-01

HISTORICAL

J708_198307

Standard

AIR BRAKE ACTUATOR DIAPHRAGM TEST PROCEDURE

1988-05-01

HISTORICAL

J1450_198805

This practice is intended for, but not limited to, testing of reinforced air brake diaphragms as they are used in vehicle service or parking brake systems.

Standard

AUTOMOTIVE PIPE FITTINGS

1993-06-01

HISTORICAL

J530_199306

This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.

Standard

AUTOMOTIVE PIPE FITTINGS

1981-01-01

HISTORICAL

J530_198101

This standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figs. 1-17 and Tables 2-7 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.

Standard

AUTOMOTIVE PIPE FITTINGS

1992-06-01

HISTORICAL

J530_199206

This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.

Standard

AUTOMOTIVE PIPE FITTINGS

1994-05-01

HISTORICAL

J530_199405

This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.

Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS

1992-02-01

HISTORICAL

J531_199202

This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.

Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS

1981-01-01

HISTORICAL

J531_198101

This standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figs. 1-6 and Tables 2-4) commonly used in automotive and related industrial applications.

Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS

1994-06-01

HISTORICAL

J531_199406

This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.