Refine Your Search

Date

Date

Topic

Topic

Author

Author

Fuel systems Casting Braking systems Tools and equipment Commercial Vehicle Standard Suppliers Cleaning

Search Results

Viewing 1 to 20 of 751
123Next >Last >>
Sort by title
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply
2020-02-25
CURRENT
J2691_202002
This SAE Standard establishes the minimum construction and performance requirements for a 15 pole connector between towing vehicles and trailers, for trucks, trailers, and dollies, for 12 VDC nominal applications in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply
2018-04-15
HISTORICAL
J2691_201804
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

A Dictionary of Terms for the Dynamics and Handling of Single Track Vehicles (Motorcycles, Mopeds, and Bicycles)
2000-01-13
HISTORICAL
J1451_200001
This dictionary of terms was prepared for use by those with a need to describe and understand the dynamics and handling of two-wheeled, single track vehicles. It is intended to span the gap between vehicle dynamics specialists and those with a more general interest. This report is pertinent to such areas as vehicle design and development, the description of two-wheeler properties, rider training and education, and the preparation of standards and regulations. This report was prepared by the SAE Motorcycle Committee, which solicits suggestions for improvements and additions to be considered in future revisions. Comments should be directed to SAE Headquarters.
Standard

A Dictionary of Terms for the Dynamics and Handling of Single Track Vehicles (Motorcycles, Mopeds, and Bicycles)
2007-08-16
HISTORICAL
J1451_200708
This dictionary of terms was prepared for use by those with a need to describe and understand the dynamics and handling of two-wheeled, single track vehicles. It is intended to span the gap between vehicle dynamics specialists and those with a more general interest. This report is pertinent to such areas as vehicle design and development, the description of two-wheeler properties, rider training and education, and the preparation of standards and regulations. This report was prepared by the SAE Motorcycle Committee, which solicits suggestions for improvements and additions to be considered in future revisions. Comments should be directed to SAE Headquarters.
Standard

A TEST FOR EVALUATING THE REARWARD AMPLIFICIATION OF MULTI-ARTICULATED VEHICLES
1993-09-01
HISTORICAL
J2179_199309
The procedure applies to heavy vehicles weighing more than 11 800 kg (26 000 lb) and particularly to those vehicles having two or more articulation joints that allow rotation in a horizontal plane. The procedure pertains to the lateral directional response of multi-articulated vehicles in avoidance maneuvers performed at highway speeds without braking.
Standard

ABS Exciter Ring Location Standardization
2023-10-02
CURRENT
J1730_202310
This SAE Recommended Practice establishes the antilock brake system (ABS) sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on or integral to the inboard end of spoke wheels, hubs, rotors, and hub-rotor assemblies on the following axle designations as defined in SAE J1842. a FF b FL c FC d FH e L f R g U h W j N k P
Standard

ABS Exciter Ring Location Standardization
2012-03-15
HISTORICAL
J1730_201203
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a FF b FL c FC d FH e L f R g U h W j N k P
Standard

ABS Exciter Ring Location Standardization
2019-02-11
HISTORICAL
J1730_201902
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a FF b FL c FC d FH e L f R g U h W j N k P
Standard

ABS Excitor Ring Location Standardization
2004-07-27
HISTORICAL
J1730_200407
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of the hub on the following axle designations. a FF b FL c L d R e U f W g N h P
Standard

AIR BRAKE ACTUATOR DIAPHRAGM TEST PROCEDURE
1988-05-01
HISTORICAL
J1450_198805
This practice is intended for, but not limited to, testing of reinforced air brake diaphragms as they are used in vehicle service or parking brake systems.
Standard

AIR RESERVOIR CAPACITY PERFORMANCE GUIDE—COMMERCIAL VEHICLES
1997-07-01
HISTORICAL
J1609_199707
This SAE Recommended Practice establishes performance guidelines for the capacity of the air reservoir systems used on trucks, towing trucks, truck-tractors, trailers, and converter dollies, with GVWRs over 10 000 lb, designed to be used on the highway in commercial operations.
Standard

AUTOMOTIVE PIPE FITTINGS
1993-06-01
HISTORICAL
J530_199306
This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.
Standard

AUTOMOTIVE PIPE FITTINGS
1992-06-01
HISTORICAL
J530_199206
This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.
Standard

AUTOMOTIVE PIPE FITTINGS
1981-01-01
HISTORICAL
J530_198101
This standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figs. 1-17 and Tables 2-7 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.
Standard

AUTOMOTIVE PIPE FITTINGS
1994-05-01
HISTORICAL
J530_199405
This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.
Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS
1992-02-01
HISTORICAL
J531_199202
This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.
Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS
1981-01-01
HISTORICAL
J531_198101
This standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figs. 1-6 and Tables 2-4) commonly used in automotive and related industrial applications.
Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS
1994-06-01
HISTORICAL
J531_199406
This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.
123Next >Last >>
X