Search Results

Standard

A Dictionary of Terms for the Dynamics and Handling of Single Track Vehicles (Motorcycles, Mopeds, and Bicycles)

2007-08-16

HISTORICAL

J1451_200708

This dictionary of terms was prepared for use by those with a need to describe and understand the dynamics and handling of two-wheeled, single track vehicles. It is intended to span the gap between vehicle dynamics specialists and those with a more general interest. This report is pertinent to such areas as vehicle design and development, the description of two-wheeler properties, rider training and education, and the preparation of standards and regulations. This report was prepared by the SAE Motorcycle Committee, which solicits suggestions for improvements and additions to be considered in future revisions. Comments should be directed to SAE Headquarters.

Standard

ACCESS SYSTEMS FOR CONSTRUCTION AND INDUSTRIAL EQUIPMENT

1970-07-01

HISTORICAL

J185_197007

This recommended practice covers the criteria for steps, ladders, walkways, platforms, grab rails (handrails), grab irons, guardrails, and entrance openings as they relate to aiding the operator and/or servicemen in performing their functions on the vehicle.

Standard

AUTOMOTIVE PIPE FITTINGS

1992-06-01

HISTORICAL

J530_199206

This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.

Standard

AUTOMOTIVE PIPE FITTINGS

1981-01-01

HISTORICAL

J530_198101

This standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figs. 1-17 and Tables 2-7 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.

Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS

1992-02-01

HISTORICAL

J531_199202

This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.

Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS

1981-01-01

HISTORICAL

J531_198101

This standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figs. 1-6 and Tables 2-4) commonly used in automotive and related industrial applications.

Standard

AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS

1994-06-01

HISTORICAL

J531_199406

This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.

Standard

Air Brake Valve - Performance Requirements

2020-12-18

CURRENT

J1410_202012

This SAE Recommended Practice establishes minimum performance requirements for new pneumatic valves when tested in accordance with the test procedure outlined in SAE J1409. The performance requirements will include: a Input-output performance b Leakage characteristics c Low temperature performance d Elevated temperature performance e Corrosion resistance performance f Endurance testing g Structural integrity

Standard

Air Brake Valve - Performance Requirements

2016-07-20

HISTORICAL

J1410_201607

This SAE Recommended Practice establishes minimum performance requirements for new pneumatic valves when tested in accordance with the test procedure outlined in SAE J1409. The performance requirements will include: a Input-output performance b Leakage characteristics c Low temperature performance d Elevated temperature performance e Corrosion resistance performance f Endurance testing g Structural integrity

Standard

Air Brake Valve Input-Output Characteristic Requirements

2016-06-17

CURRENT

J1861_201606

This SAE Recommended Practice establishes minimum tolerance requirements for pilot operated and mechanically actuated modulating type valves, and through type valves used in the service brake control system when tested in accordance with the test procedure outlined in SAE J1859. This document applies to the nominal input-output characteristics as specified by vehicle original equipment manufacturer and labeled by the valve manufacturer as outlined in SAE J1860. The tolerance requirements will include: a Crack (opening) pressure or force. Crack pressure may be measured at the initial output pressure or as the pressure differential before output pressure exceeds 14 kPa (2 psi). Crack force may be measured at initial output pressure or before output pressure exceeds 14 kPa (2 psi). b Pressure differential (input-output)

Standard

Air Brake Valve Input-Output Characteristic Requirements

2011-09-12

HISTORICAL

J1861_201109

This SAE Recommended Practice establishes minimum tolerance requirements for pilot operated and mechanically actuated modulating type valves, and through type valves used in the service brake control system when tested in accordance with the test procedure outlined in SAE J1859. This document applies to the nominal input-output characteristics as specified by vehicle original equipment manufacturer and labeled by the valve manufacturer as outlined in SAE J1860. The tolerance requirements will include: a Crack (opening) pressure or force. Crack pressure may be measured at the initial output pressure or as the pressure differential before output pressure exceeds 14 kPa (2 psi). Crack force may be measured at initial output pressure or before output pressure exceeds 14 kPa (2 psi). b Pressure differential (input-output)

Standard

Air Dryer Test Procedure

2012-11-09

HISTORICAL

J2384_201211

This SAE Recommended Practice establishes uniform Test Procedures for desiccant Air Dryers used in vehicles with compressed air systems per SAE J2383. Continuous flow desiccant Air Dryers are excluded from the scope of this document.

Standard

Alternator Remanufacturing/Rebuilding Procedures Includes Passenger Car, Heavy Duty, Industrial, Agricultural, and Marine

2008-05-13

CURRENT

J2075_200805

These remanufacturing procedures are recommended minimum guidelines (with theunderstanding that being more critical is acceptable) for use by remanufacturers/rebuilders of alternators to promote consistent reliability, durability, and safety of remanufactured alternators. Installation of remanufactured or rebuilt products is often an economical way to repair an application even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer/rebuilder should determine if the original design and present condition of the core are suitable for remanufacturing/rebuilding so as to provide durable operation of the part as well as acceptable performance when installed on the application. The remanufacturer/rebuilder should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding this product.

Standard

Ambulance Interior Storage Compartment Integrity

2016-11-01

HISTORICAL

J3058_201611

This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable supply pouch systems when exposed to a frontal, side or rear impact (i.e., a crash impact). Its purpose is to provide component manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure interior Storage Compartments or systems meet the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.

Standard

Automotive Tube Fittings

2017-05-30

HISTORICAL

J512_201705

This SAE Standard covers complete general and dimensional specifications for the various types of tube fittings intended for general application in the automotive, appliance, and allied fields. See SAE J1131 for the performance requirements of reusable (push to connect) fittings intended for use in automotive air brake systems. Flare type fittings shall be as specified in Figures 1 to 4 and Tables 3 to 5. NOTE—For sizes 3/16 to 3/8 and 1/2 to 3/4 the flare type fittings depicted in Figures 1A to 3C are identical with the corresponding refrigeration tube fittings specified in SAE J513. Special size combination fittings 3/16 to 3/8 and 1/2 to 3/4 shall be as specified in SAE J513. Inverted flared type fittings shall be as specified in Figures 5 to 11 and Tables 3, 6, 7, 8, and 9. Gages and gaging procedures pertaining to inverted flared tube fittings are given in Appendix A.

Standard

Average Vehicle Dimensions for Use in Designing Docking Facilities for Motor Vehicles

2011-06-13

CURRENT

J699_201106

This SAE Recommended Practice establishes limits for empty vehicle floor heights and provides limits of vehicle dimensions for use in designing docking facilities for motor vehicles.

Standard

Brake Effectiveness Marking for Brake Blocks - Truck and Bus

2019-06-06

CURRENT

J1801_201906

This SAE Recommended Practice provides the method to assign numerical values of brake effectiveness, using data from single station inertia dynamometer effectiveness tests, and to identify a uniform procedure to mark these values on the edge of brake blocks in excess of 12.7 mm (0.51 in) in thickness.

Standard

Brake Effectiveness Marking for Brake Blocks—Truck and Bus

2014-10-27

HISTORICAL

J1801_201410

This SAE Recommended Practice provides the method to assign numerical values of brake effectiveness, using data from single station inertia dynamometer effectiveness tests, and to identify a uniform procedure to mark these values on the edge of brake blocks in excess of 12.7 mm (0.51 in) in thickness.

Standard

Brake Force Distribution Field Test Procedure for Truck and Bus

2003-04-29

HISTORICAL

J225_200304

This SAE Recommended Practice provides a field test procedure and instructions for: a Instrumentation and Equipment b Vehicle Preparation c Test of air-braked single and combination vehicles d Calculation of brake force distribution e This test procedure is intended to be used as a field procedure. If a more refined method, utilizing laboratory equipment, is required, refer to SAE J1505.

Standard

Brake System Test Procedure - Snowmobiles

2016-08-09

HISTORICAL

J45_201608

This SAE Recommended Practice establishes a uniform procedure for the level surface testing of hand-operated brake systems on recreational noncompetitive snowmobiles.