Search Results

A braking force distribution strategy in integrated braking system composed of the main braking system and the auxiliary braking system based on braking pad wear control and hitch force control under non-emergency braking condition is proposed based on the Electronically Controlled Braking System (EBS) to reduce the difference in braking pad wear between different axles and to decrease hitch force between tractors and trailers. The proposed strategy distributes the braking force based on the desired braking intensity, the degree of the braking pad wear and the limits of certain braking regulations to solve the coupling problems between braking safety, economical efficiency of braking and the comfort of drivers. Computer co-simulations of the proposed strategy are performed.

Taking a good longitudinal braking performance on flat and level road of tractor and semi-trailer combination as a target, in order to achieve an ideal braking force distribution among axles, while the vehicle deceleration is just depend on the driver's intention, not affected by the variation of semi-trailer mass, the paper proposes a model based vehicle mass identification and braking force distribution strategy. The strategy identifies the driver's braking intention via braking pedal, estimates semi-trailer's mass during the building process of braking pressure in brake chamber, distributes braking force among axles by using the estimated mass. And a double closed-loop regulation of the vehicle deceleration and utilization adhesion coefficient of each axle is presented, in order to eliminate the bad effect of mass estimation error, and enhance the robustness of the whole algorithm. A simulation is conducted by utilizing MATLAB/Simulink and TruckSim.

Heavy commercial vehicles have large variations in load and high centroid positions, so it is particularly important to obtain timely and accurate load information during driving. If the load information can be accurately obtained and the braking force of each axle can be distributed on this basis, the braking performance and safety of the entire vehicle can be improved. Heavy commercial vehicle load information is different from passenger vehicles, so it is particularly important to study commercial vehicles engaged in freight and passenger transportation. Presently, numerous research endeavors focus on evaluating the quality of passenger vehicles. However, heavy commercial vehicles exhibit notable distinctions compared to their passenger counterparts. Due to substantial variations in vehicle mass pre and post-loading, coupled with notable suspension deformations, significant changes are observed.

The simulation of electro-pneumatic components used in brake systems of commercial vehicles is of great importance in order to understand their characteristics for developing a control logic and improve the braking performance. As the goal of improving the performance of the commercial vehicle pneumatic EBS(Electronically controlled Braking System), static and dynamic characteristics of proportional relay valve for commercial vehicle pneumatic EBS have been simulated by using MATLAB/Simulink environment and validated by testing on hardware-in-the-loop test bench focused on its pressure hysteresis characteristic. The simulation and test results show that the mathematic model for proportional relay valve characteristics is reasonable and reliable, and this simulation tool can be used for research and developing of pneumatic EBS system for commercial vehicle effectively.

For city buses, especially hybrid electric buses, the requirements for the fuel economy and low noises are stricter, comparing with the momentum quality. Since hybrid electric buses sometimes run without the engine, the noises that the transmission makes become the major type. To get better fuel economy and lower noises, this paper focuses on optimizing the characteristics of the automatic mechanical transmission (AMT) in a hybrid electric city bus, and the studies are done as follows. Firstly, in order to reduce the fuel consumption, the transmission ratios are optimized by the co-simulation and optimization in CRUISE and MATLAB, with the limitation of the quality of driving momentum. Secondly, for the purpose of lightweight and lower transmission noise, multi-objective optimization based on reliability is applied in transmission geometric optimization design, the objective function are the smallest volume and the biggest transmission gear contact ratio of the transmission.

The hybrid electric city bus, which consists of the electric motor and battery, is obviously different from the traditional buses. This paper focuses on optimizing the characteristics of the automatic mechanical transmission in hybrid electric city bus and does the following studies: firstly, in order to reduce the fuel consumption, the transmission ratio and some structural parameters are optimized with CRUISE software; secondly, the volume and weight of the transmission structure is reduced and optimized by numerical optimization approach, with the limitation of the structural reliability.

A brake pad wear control algorithm used under non-emergency braking conditions is proposed to reduce the difference in brake pad wear between the front and rear axles caused by the difference in brakes and braking force. According to the adhesion state of the pad wear, the control algorithm adjusted the braking force distribution ratio of front and rear wheel that balanced adhesion pad wear value. Computer co-simulations of braking with Trucksim and Matlab/Simulink using vehicle models with equal brake pad wear, greater wear on the front axle and greater wear on the rear axle respectively is performed. The computation simulation results show that meet the brake force distribution system regulatory requirements and total vehicle braking force unchanged.