Search Results

The in-cylinder direct injection of fuels can be a further step towards cleaner and more efficient internal combustion engines. However, the injector design and its characterization, both experimental and from numerical simulation require accurate diagnostics and efficient models. This work aims to simulate the complex behavior of the gaseous and liquid jets through an outwardly opening injector characterized by optical diagnostics using a one-dimensional model without using three dimensional models. The behavior of the jet from an outwardly opening injector changes according to the type of fuel. In the case of the gas, the experimental investigations put in evidence three main jet regions: 1) near-field region where the jet shows a complex gas-dynamic structure; 2) transition region characterized by intense mixing; 3) far-field region characterized by a fully developed subsonic turbulent jet.

This paper describes the after-treatment technology that could be used to meet a future BS-VII standard, considering close-coupled SCR (cc-SCR) to help start NOx conversion earlier. Both active (Cu/Fe-SCR based) and passive (V-SCR based) systems have the potential to meet emission limits. V-SCR may be considered in the rear position because V-SCR shows a fast response with very low N2O formation. Next-gen V-SCR technology shows significantly improved performance and durability closer to Cu-SCR. The steady-state NOx conversions over Next-Gen V-SCR were better than BS-VI V-SCR in both fresh and aged-580°C/100h conditions. High durability was also observed after engine aging of 1000h (WHTC + high load). Another big challenge in BS VII could be the PN10 requirement. With enhanced filtration coating (EFC) technology, PN emissions drop drastically in comparison to Euro VI reference without EFC to meet a future BS VII.

Predicting fatigue performance in concentrated contacts under thin film (or mixed) lubrication conditions has historically involved various empirical approaches. Typically a lubrication parameter is used in an experimentally derived equation to predict the expected rolling contact performance. However, this model doesn't explain the performance improvements. Enhanced finish bearings have exhibited longer life than standard finish bearings, especially when bearings are operated with thin EHL film. In this paper, the contact surfaces of test bearings were analyzed by using a micro-macro contact model in which the macro-contact was elastic contact, and the micro-contact was elastic-plastic contact. The interior subsurface stress maps were calculated from the real contact surfaces, which included the effects of roughnesses, waviness, and profiles.

Current trends in environmental and emissions regulations are driving changes in new engine systems, and increasing the need for more effectively sealed joints in exhaust systems. At the high temperatures in these exhaust systems it is difficult for traditional gaskets to provide an effective seal, as they degrade at high operating temperatures. This paper introduces a coating that has both excellent temperature stability and good compliance, thus forming an excellent sealing enhancement for metallic layers in exhaust system gaskets. Temperature stability data is presented along with sealing data, which illustrate the superior performance of this material compared to current systems.

We propose a novel dual-fuel combustion model for simulating heavy-duty engines with the G-Equation. Dual-Fuel combustion strategies in such engines features direct injection of a high-reactivity fuel into a lean, premixed chamber which has a high resistance to autoignition. Distinct combustion modes are present: the DI fuel auto-ignites following chemical ignition delay after spray vaporization and mixing; a reactive front is formed on its surroundings; it develops into a well-structured turbulent flame, which propagates within the premixed charge. Either direct chemistry or the flame-propagation approach (G- Equation), taken alone, do not produce accurate results. The proposed Dual-Fuel model decides what regions of the combustion chamber should be simulated with either approach, according to the local flame state; and acts as a “kernel” model for the G- Equation model. Direct chemistry is run in the regions where a premixed front is not present.

Combustion control strategy for high efficiency and low emissions in a heavy duty (H D) diesel engine was investigated experimentally in a single cylinder test engine with a common rail fuel system, EGR (Exhaust Gas Recirculation) system, boost system and retarded intake valve closing timing actuator. For the operation loads of IMEPg (Gross Indicated Mean Effective Pressure) less than 1.1 MPa the low temperature combustion (LTC) with high rate of EGR was applied. The fuel injection modes of either single injection or multi-pulse injections, boost pressure and retarded intake valve closing timing (RIVCT) were also coupled with the engine operation condition loads for high efficiency and low emissions. A higher boost pressure played an important role in improving fuel efficiency and obtaining ultra-low soot and NOx emissions.

Biofuel can enable a sustainable transport solution and lower greenhouse gas emissions compared to standard fuels. This study focuses on biodiesel, implemented in the easiest way as drop in fuel. When mixing biodiesel into diesel one can run into problems with solubility causing contaminants precipitating out as insolubilities. These insolubilities, also called soft particles, can cause problems such as internal injector deposits and nozzle fouling. One way to overcome the problem of soft particles is by filtration. It is thus of great interest to be able to quantify fuel filters’ ability to intercept soft particles. The aim of this study is to test different fuel filters for heavy-duty engines and their ability to filter out synthetic soft particles. A custom-built fuel filter rig is presented, together with some of its general design requirements. For evaluation of the efficiency of the filters, fuel samples were taken before and after the filters.

The titanium alloy system offers a range of properties conducive to weight/space savings. These properties include high strength, low elastic modulus and low density, which uniquely suit them for spring applications. By utilizing titanium in various spring designs, suspension engineers can save up to 60% of the weight and 20-30% of the space for a comparable steel spring. The primary impediment to widespread titanium part production and use in the past was cost. A new low cost titanium alloy system designed specifically for suspension and drive train application has been tested and proved to limit this cost problem. Working with titanium in their suspension designs, engineers will save significant weight/space over comparable steel and aluminum components.

A new transparent type electrochromic device (ECD) has been developed. It consists of two electrochromic thin films facing each other, one of “prussian blue” (PB) and the other of tungsten trioxide (WO3). PB exhibits a high intensity of coloration and is blue in the oxidized state and transparent in the reduced state. By electrodeposition, the PB layer can be formed on large substrates at low cost. This ECD has been applied to large, curved automotive glass. It reversibly turns from dark blue to transparent at low operating voltage and maintains the same intensity of coloration without the aid of an external power supply. Compared with photochromic glass, it achieves a greater color change in a shorter time and its light absorption can be changed at will. It shields passengers from the discomfort of glare and heat flow through glass.

To reduce heat transfer between hot gas and cavity wall, thin Zirconia (ZrO2) layer (0.5mm) on the cavity surface of a forged steel piston was firstly formed by thermal spray coating aiming higher surface temperature swing precisely synchronized with flame temperature near the wall resulting in the reduction of temperature difference. However, no apparent difference in the heat loss was analyzed. To find out the reason why the heat loss was not so improved, direct observation of flame impingement to the cavity wall was carried out with the top view visualization technique, for which one of the exhaust valves was modified to a sapphire window. Local flame behavior very close to the wall was compared by macrophotography. Numerical analysis by utilizing a three-dimensional simulation was also carried out to investigate the effect of several parameters on the heat transfer coefficient.

Recent research on carburized steels has demonstrated a correlation between the toughness properties of a carburized steel and the fatigue performance in combined load testing (high-cycle fatigue plus overload). The data presented suggest that, for applications where loads above the fatigue limit are encountered, both processing and alloying must be considered. Results from a number of investigations are reviewed to illustrate that high-cycle fatigue properties are controlled primarily by the processing, whereas toughness characteristics, such as resistance to random cyclic loading, are a result of the alloying.

Abstract In view of the combustion efficiency and emission performance, various new clean combustion modes put forward higher requirements for the performance of the fuel injection system, and the cavitating two-phase flow characteristics in the injector nozzle have a significant impact on the spray atomization and combustion performance. This article comprehensively discusses and summarizes the factors that affect cavitation and the effectiveness of cavitation, and presents the research status and existent problems under each factor. Among them, viscosity factors are a hot research topic that researchers are passionate about, and physical properties factors still have the value of further in-depth research. However, the importance of material surface factors ranks last since the nozzle material was determined. Establishing a more comprehensive cavitation–atomization model considering various factors is the focus of research on cavitation phenomena.

Correlations of simply calculated fuel spray parameters with measured ISFC and smoke trends in a swirling direct injection diesel engine are described. These are based on a large number of results from experiments carried out on a 120.7 mm bore engine in which the induction swirl could be varied. The correlations indicate that (i) the fuel spray tip velocity at impingement on the chamber wall and (ii) the ‘crosswind’ over the spray at impingement have important influences. Based on these it is deduced that engine speed-related turbulence is a rate-controlling factor in DI diesel combustion.

The Second Auto Works of China has been extensively using boron steels in its truck manufacture with accumulation of experience over 20 years, four grades of boron steels are now in regular production with accumulated consumption of about 450,000 tons. Another three grades are in different R&D stages. A new steel series based on silicon manganese, vanadium and boron has come into being. All manufactured parts must stand field teats on very difficult terrain on the Chinese land. It has been proved by practice that boron steels can cope with requirements of truck design, manufacture and field usage. They are economical not only financially, but also on strategic material consumption. Also presented are discussions on boron steel peculiarities.

Maintaining the fuel temperature and fuel system components below certain values is an important design objective. Predicting these temperatures is therefore one of the key parts of the vehicle’s thermal management process. One of the physical processes affecting fuel tank temperature is fuel vaporization, which is controlled by the vapor pressure in the tank, fuel composition and fuel temperature. Models are developed to enable the computation of the fuel temperature, fuel vaporization rate in the tank, fuel temperatures along the fuel supply lines, and follow its path to the charcoal canister and into the engine intake. For diesel fuel systems where a fuel return line is used to return excess fluid back to the fuel tank, an energy balance will be considered to calculate the heat added from the high-pressure pump and vehicle under-hood and underbody.

The good relationship between the spray condition in the intake manifold and the combustion characteristics is required. Firstly by this report it was tried the visualization and observation of spray of gasoline injection. It was mainly photographed when injection just began and the spray impinged on a intake valve. The photographs of fuel spray were taken by a image converter type high speed camera. The characteristics of the fuel spray injected in early injection period is influenced with fuel pressure and flow rate of fuel. The atomizing phenomenon of tip fuel of spray could be visualized. The atomizing process in early injection period are differ from that in stady-state spray. And the picture of spray at impingement on the intake valve was shown too. The atomizing condition on the valve surface could be observed visually.

The larger the equipment for a specific job in the earth-moving field, the more quickly and efficiently that job can be done. Unfortunately, the very size and weight of many present units means that the transportation of them involves a ponderous task. If increased capacity could be obtained with no increase in gross vehicle weight, and with only negligible differences in dimensions, major progress could be made in the equipment field. Even if physical dimensions involved no problem, the weight and placement of such essentials as tires, wheels, brakes, drive chains and engines, all tend to limit the payload capacity of a given vehicle. Through the judicious use of aluminum alloys in proved applications, a 10 to 15 per cent increase in payload capacity can readily be achieved at no increase in gross vehicle weight. The aluminum applications referred to have been proved both in over-the-road and in off-highway service.

AMS-STD-595A Color Chips Precise Color Matching, Individual Color Chips: A 3 x 5 inch color chip supplied in a 3 x 5 inch protective envelope for each AMS-STD-595 color, suitable for matching quality control inspection purposes. SAE Product Code: EA-10032 AMS-STD-595 – Colors Used in Government Procurement. This standard presents the colors used by Government Activities in a format suitable for color selection matching and for quality control inspection for paints and coatings. Standard is used with DoD and other Federal Agencies as a primary source of color reference.

This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.