Refine Your Search

Date

Date

Topic

Topic

Commercial Vehicle Materials Suppliers Ferrous metals Trucks Chassis MTC1, Earthmoving Machinery

Search Results

Viewing 1 to 20 of 31
12Next >Last >>
Sort by title
Standard

CAPACITY RATING—ELEVATING SCRAPERS
1993-06-01
HISTORICAL
J957_199306
This SAE Standard specifies a procedure for approximating the volume of a typical material carried in the bowl of an elevating scraper as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and a representative volume on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

Component Nomenclature--Dumpers
2000-06-28
CURRENT
J1016_200006
This SAE Standard provides names of major components peculiar to dumpers as defined in SAE J1057 (See Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine. For component nomenclature for dumper trailers, refere to SAE J734.
Standard

Earthmoving Machinery—Coupling of Attachments to Skid Steer Loaders
2000-06-28
HISTORICAL
J2513_200006
This SAE Standard sets forth standard dimension requirements for the loader attachment bracket and attachment interface to allow interchangeability of attachments on skid steer loaders whose operating mass (see SAE J/ISO 6165) is 4,500 kg or less. Narrow skid steer loaders may have a width that does not allow compliance with this standard. The design of the loader attachment bracket locking system is not restricted by this standard and is left to the discretion of the manufacturer.
Standard

IDENTIFICATION TERMINOLOGY—PIPELAYERS
1980-06-01
HISTORICAL
J1295_198006
This standard applies to machines which are designed to raise, lower, and carry pipe and loads of similar nature. The term pipelayer does not include tractors or loaders with side booms which are optional attachments, manufacturer or dealer-installed, to machines as defined in SAE J1057. Note: Some related standards will apply equally to pipelayers and to tractors and loaders with side boom. Two such standards are SAE J743 and ANSI B30.14.
Standard

LIFT CAPACITY CALCULATION AND TEST PROCEDURE PIPELAYER AND SIDEBOOM
1992-03-01
HISTORICAL
J743_199203
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

LOADING ABILITY TEST CODE--SCRAPERS
1985-11-01
HISTORICAL
J764_198511
The code applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.) The loading procedure is limited to standing starts in order to reduce the number of variables that are difficult to control and measure. Because of the difficulties in controlling some of the other variables, meaningful numerical comparison of time and load from scraper to scraper requires that data be taken at the same time and place, and that the units being compared be of approximately equal capacity.
Standard

LOADING ABILITY TEST CODE—SCRAPERS
1977-06-01
HISTORICAL
J764_197706
The code applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See J1116 and J1057a.) The loading procedure is limited to standing starts in order to reduce the number of variables that are difficult to control and measure. Because of the difficulties in controlling some of the other variables, meaningful numerical comparison of time and load from scraper to scraper requires that data be taken at the same time and place, and that the units being compared be of approximately equal capacity.
Standard

Lift Capacity Calculation Method Scrap and Material Handlers
2019-04-15
CURRENT
J2518_201904
This SAE Standard provides a uniform method to calculate the lift capacity of scrap and material handlers, establishes definitions and specifies machine conditions for the calculations. This document applies to scrap and material handlers as defined in SAE J2506 that have a 360 degrees continuous rotating upper structure. It does not apply to equipment that is incapable of lifting a load completely off the ground. This document applies to those machines that are crawler, wheel, rail and pedestal or stationary mounted.
Standard

Lift Capacity Calculation and Test Procedure Pipelayer and Sideboom
2000-06-01
HISTORICAL
J743_200006
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Loading Ability Test Procedure - Scrapers
2011-10-27
CURRENT
J764_201110
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
Standard

Loading Ability Test Procedure—Scrapers
2006-02-05
HISTORICAL
J764_200602
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
12Next >Last >>
X