Search Results

The demand for improved fuel economy in both cars and trucks has emphasized the need for lighter weight components. The application of high strength steel to wheels, both rim and disc, represents a significant opportunity for the automotive industry. This paper discusses the Ranger HSLA wheel program that achieved a 9.7 lbs. per vehicle weight savings relative to a plain carbon steel wheel of the same design. It describes the Ranger wheel specifications, the material selection, the metallurgical considerations of applying HSLA to wheels, and HSLA arc and flash butt welding. The Ranger wheel design and the development of the manufacturing process is discussed, including design modifications to accommodate the lighter gage. The results demonstrate that wheels can be successfully manufactured from low sulfur 60XK HSLA steel in a conventional high volume process (stamped disc and rolled rim) to meet all wheel performance requirements and achieve a significant weight reduction.

A pin and disc machine has been modified for the evaluation of silver-steel lubrication characteristics of railroad diesel oils. Use of silver pins on polished steel discs at selected loads and rubbing speeds allows good correlation with known engine behavior. In comparison with wear and friction data obtained by the four ball method, this pin and disc test gives better correlation with engine tests than the Modified Four Ball Test.

This paper presents a multidimensional approach to the hydraulic components design by means of an open-source fluid dynamics code. A preliminary study of a basic geometry was carried out by simulating the efflux of an incompressible fluid through circular pipes. Both laminar and turbulent conditions were analyzed and the influence of the grid resolution and modeling settings were investigated. A qualitative description of the internal flow-field distribution, and a quantitative comparison of pressure and velocity profiles along the pipe axis were used to asses the multidimensional open-source code capabilities. Moreover the results were compared with the experimental measurements available in literature and with the theoretical trends which can be found in well-known literature fundamentals (Hagen-Poiseuille theory and Nikuradse interpolation). Further comparison was performed by using a commercial CFD code.

Engine mounts are an integral part of the vehicle that helps in reducing the vibrations generated from the engine. Engine mounts require a simple yet complicated amalgamation of two very different materials, steel and rubber. Proper adhesion between the two is required to prevent any part failure. Therefore, it becomes important that a comprehensive study is done to understand the mating phenomenon of both. A good linking between rubber and metal substrate is governed by surface pretreatment. Various methodologies such as mechanical and chemical are adopted for the same. This paper aims to present a comparative study as to which surface pretreatment has an edge over other techniques in terms of separation force required to break the bonding between the two parts. The study also presents a cost comparison between the techniques so that the best possible technique can be put to use in the commercial vehicle industry.

This paper describes the results of a series of fatigue studies relating the lives of several weld geometries. Rotating beam and axially loaded specimens were used. A comparison between steel and plastic (polyvinylchloride scale models is made. Using plastic scale models of welded structures for fatigue life determination is the ultimate goal of this work.

“Today, wearing parts are regularly subjected to abnormal loading conditions. They must be able to accept these conditions without failure. In continuous operations, unscheduled downtime greatly increases maintenance costs, not to mention the cost of lost production. White iron castings offer premium abrasion resistance for many of these applications, but are often not used due to the possibility of brittle failure and the difficulty of mechanical attachment. This paper discusses the properties and applications of a composite of martensitic white iron and mild steel. This laminate will accept medium to high impact without loss of service failure, and can be installed by mechanical means or with welded attachment.”

Current trends in environmental and emissions regulations are driving changes in new engine systems, and increasing the need for more effectively sealed joints in exhaust systems. At the high temperatures in these exhaust systems it is difficult for traditional gaskets to provide an effective seal, as they degrade at high operating temperatures. This paper introduces a coating that has both excellent temperature stability and good compliance, thus forming an excellent sealing enhancement for metallic layers in exhaust system gaskets. Temperature stability data is presented along with sealing data, which illustrate the superior performance of this material compared to current systems.

A software tool has been developed to aid designers and process engineers in the development and improvement of heat treat processes. This tool, DANTE™, combines metallurgical phase transformation models with mass diffusion, thermal and mechanical models to simulate the heating, carburization, quenching and tempering of steel parts. The technology behind the DANTE software and some applications are presented in this paper.

Paper describes analysis of the design process of modern automotive LPG and CNG containers. Over decade experience in the field of both computer based analysis as well as in the real conditions testing has been collected and presented in the paper. Authors present the potentials of modern FEM methodologies in the optimization and production of lightweight steel containers. It has been proved that the most sophisticated numerical analysis have to be followed by the construction verification, particularly considering direct exposure to fire. Bonfire test have become obligatory for both liquid and compressed gases containers. Properly chosen fire protection system, together with the adequate level of quality of materials applied for its production together with proper directing of the gas flowing out from safety devices are the essential factors defining gas containers fire safety.

This paper presents some of the history of the Spacemetal process development; a discussion of the core forming machine, a description of the welder where corrugated core and facing sheets are joined; the quality control process employed for inspecting the finished product; and some of the material properties and applications. FOREWORD Development of a production process and the machines for fabrication of a resistance welded steel sandwich was made by Missile Division, North American Aviation, Inc. Development was carried forward under contract AF 33(600)-26154 from the Manufacturing Methods Branch, Industrial Resources Division of the Air Materiel Command USAF.

A method for the analysis of a damaged bearing is described. An emphasis is placed on obtaining complete and accurate application information; conducting a thorough visual examination; making physical measurements as necessary; and conducting metallurgical tests. The method has been used for tapered roller bearings as well as a variety of other components of various steel types and processing histories.

Overloading of trucks can easily cause damage to roads, bridges and other transportation facilities, and accelerate the fatigue loss of the vehicles themselves, and accidents are prone to occur under overload conditions. In recent years, various countries have formulated a series of management methods and governance measures for truck overloading. However, the detection method for overload behavior is not efficient and accurate enough. At present, the method of dynamic load identification is not perfect. No matter whether it is the dynamic weight measurement method of reconstructing the road surface or the non-contact dynamic weight measurement method, little attention is paid to the difference of different vehicles. Especially for different vehicles, there should be different load limits, and the current devices are not smart enough.

This study was undertaken to identify methods of unique identification of commercial vehicles at the roadside for slow and high-speed electronic screening purposes. It is a comprehensive look at available and emerging technologies, focusing on the needs of the Federal Highway Administration’s Office of Motor Carrier and Highway Safety (OMCHS) and the States. The study included both a needs assessment and a technology evaluation. A preliminary list of 22 technologies was developed that appeared to have some applicability to the task of roadside identification of commercial vehicles. As the technology evaluation progressed, five of these technologies (optical character recognition, radio frequency identification, barcode, image capture, and voice recognition) emerged as demonstrating the greatest potential for roadside identification of commercial vehicles. These five technologies were evaluated in some detail, and recommendations were developed.

The titanium alloy system offers a range of properties conducive to weight/space savings. These properties include high strength, low elastic modulus and low density, which uniquely suit them for spring applications. By utilizing titanium in various spring designs, suspension engineers can save up to 60% of the weight and 20-30% of the space for a comparable steel spring. The primary impediment to widespread titanium part production and use in the past was cost. A new low cost titanium alloy system designed specifically for suspension and drive train application has been tested and proved to limit this cost problem. Working with titanium in their suspension designs, engineers will save significant weight/space over comparable steel and aluminum components.

To reduce heat transfer between hot gas and cavity wall, thin Zirconia (ZrO2) layer (0.5mm) on the cavity surface of a forged steel piston was firstly formed by thermal spray coating aiming higher surface temperature swing precisely synchronized with flame temperature near the wall resulting in the reduction of temperature difference. However, no apparent difference in the heat loss was analyzed. To find out the reason why the heat loss was not so improved, direct observation of flame impingement to the cavity wall was carried out with the top view visualization technique, for which one of the exhaust valves was modified to a sapphire window. Local flame behavior very close to the wall was compared by macrophotography. Numerical analysis by utilizing a three-dimensional simulation was also carried out to investigate the effect of several parameters on the heat transfer coefficient.

The design and development of a new four-stroke two-cylinder diesel engine family of 1.29 litre capacity for off road are discussed. The engine is in naturally aspirated and turbocharged and intercooled versions and rated from 11.9 kW/1500 rpm to 25.7 kW/2500 rpm. The engines were tuned for air and fuel flows, air utilisation, fuel air mixing, performance and emissions at steady state at a development lab and later certified in national labs. The high altitude capability of the TCIC was checked using a model. The engines rated at less than 19 kW satisfy India Generator set and off road norms of India and Europe equivalent to USTier4 standard, and at higher ratings, standard equivalent to US Tier4-interim. In the second part of the paper, the design of coolant and oil pumps, oil cooler for TCIC engine and the piston with steel oil control ring are discussed. The higher loaded TCIC engines use fillet hardened crankshafts of chromium molybdenum steel.

The vehicle overload seriously jeopardizes traffic safety and affects traffic efficiency. At present, the static weighing station and weigh-in-motion station are both relatively fixed, so the detection efficiency is not high and the traffic efficiency is affected; the on-board dynamic weighing equipment is difficult to be popularized because of the problem of being deliberately damaged or not accepted by the purchaser. This paper proposes an efficient, accurate, non-contact vehicle overload identification method which can keep the road unimpeded. The method can detect the vehicle overload by the relative distance (as the characteristic distance) between the dynamic vehicle's marking line and the road surface. First, the dynamics model of the vehicle suspension is set up. Then, the dynamic characteristic distance of the traffic vehicle is detected from the image acquired by the calibrated camera based on computer vision and image recognition technology.

A farm tractor protection cab made of thin steel sheet pressings is described. The cab is designed and produced using entirely automotive-type procedures. Curved glasses and a dampening suspension of the glasses are found to be an important means of achieving a low noise level in the cab. Using the pressing technique when producing a steel cab makes it possible to give the various cab details rigidity with a minimum of material. When welded together, these details form a very stiff cab body, which gives the necessary mechanical strength. The curved surfaces, the radii, and the round forms, which from a tooling point of view are natural for pressed steel parts, also have a vibration-dampening effect on the entire cab construction, thus making it easier to design a quiet tractor cab. Mounted on a farm tractor of conventional design, the cab meets the noise rating number ISO N85.

It is apparent that a new generator and regulator design is needed to supply the additional electrical loads and meet the requirements for durability, reliability, and environmental protection on earthmoving equipment. The author discusses the d-c and alternator type systems which have been used to supply electrical needs. A detailed analysis of the integral charging system is presented. This system overcomes many of the shortcomings of the present electrical systems and, because it has a minimum number of moving parts, it is potentially the most reliable charging system in use on heavy duty equipment.

Recent research on carburized steels has demonstrated a correlation between the toughness properties of a carburized steel and the fatigue performance in combined load testing (high-cycle fatigue plus overload). The data presented suggest that, for applications where loads above the fatigue limit are encountered, both processing and alloying must be considered. Results from a number of investigations are reviewed to illustrate that high-cycle fatigue properties are controlled primarily by the processing, whereas toughness characteristics, such as resistance to random cyclic loading, are a result of the alloying.