Search Results

Advanced Vehicle Technologies (AVT), a Ballarat Australia based company, has developed the World's first diesel to 100% LPG conversion for heavy haul trucks. There is no diesel required or utilized on the trucks. The engine is converted with minimal changes into a spark ignition engine with equivalent power and torque of the diesel. The patented technology is now deployed in 2 Mercedes Actros trucks. The power output in engine dynamometer testing exceeds that of the diesel (in excess of 370 kW power and 2700 Nm torque). In on-road application the power curve is matched to the diesel specifications to avoid potential downstream power-train stress. Testing at the Department of Transport Energy & Infrastructure, Regency Park, SA have shown the Euro 3 truck converted to LPG is between Euro 4 and Euro 5 NOx levels, CO2 levels 10% better than diesel on DT80 test and about even with diesel on CUEDC tests.

Three-dimensional transient simulation was performed and an autoignition model was implemented to predict knock occurrence and autoignition site in a heavy-duty liquefied petroleum gas (LPG) engine. A flame area evolution (FAE) premixed combustion model was applied to simulate flame propagation. Engine experiments using a single-cylinder research engine were performed to calibrate the reduced kinetic model and to verify the result of this modeling. A pressure transducer and a head-gasket type ion-probe circuit board were installed to detect knock occurrence, flame arrival angle, and autoignition site. The simulation result shows good agreement with engine experiments. It also provides much information about in-cylinder phenomena and some ways to reduce knocking tendency. This knock simulation can be used as a development tool of engine design.

This paper describes the conversion of a stationary spark ignition engine to a heavy duty (HD) natural gas engine suitable for transportation applications, in response to the new urban truck and bus legislation of 1994 and 1998. The approach to the fuel and ignition control system is to use a microprocessor controlled engine management system based on inputs from combustion air and natural gas mass flow sensors. As the emission control system is also based on stoichiometric three way catalyst technology, it is felt that the control approach is very robust. The engine and control system were first mounted on a HD dynamometer for the development work where engine control parameters were calibrated. In addition steady state emission data were collected and estimates of the HD transient emission levels were obtained.

This paper presents the results of a two-phase Philippine study to determine the actual mileage (km/liter) of in-use diesel and LPG (liquefied petroleum gas or Auto-LPG) public utility jeepneys plying two separate Metro Manila urban routes using both on-road and chassis dynamometer tests. Measured average load factor in on-road tests was 60-70%. Dynamometer tests at 100% load factor utilized drive cycles derived from on-road speed data. A “diesel equivalent mileage” of actual LPG mileage, deemed indicative of LPG “fuel energy conversion efficiency” relative to diesel, was calculated (based solely on fuel heating values and densities) for comparing actual mileage from both fuels. The LPG actual mileage in both on-road and laboratory tests was lower than diesel mileage. In on-road tests, the LPG actual mileage was lower than diesel actual mileage by about the same percentage LPG heating value was lower than diesel’s per liter of fuel.

Paper describes analysis of the design process of modern automotive LPG and CNG containers. Over decade experience in the field of both computer based analysis as well as in the real conditions testing has been collected and presented in the paper. Authors present the potentials of modern FEM methodologies in the optimization and production of lightweight steel containers. It has been proved that the most sophisticated numerical analysis have to be followed by the construction verification, particularly considering direct exposure to fire. Bonfire test have become obligatory for both liquid and compressed gases containers. Properly chosen fire protection system, together with the adequate level of quality of materials applied for its production together with proper directing of the gas flowing out from safety devices are the essential factors defining gas containers fire safety.

We propose a novel dual-fuel combustion model for simulating heavy-duty engines with the G-Equation. Dual-Fuel combustion strategies in such engines features direct injection of a high-reactivity fuel into a lean, premixed chamber which has a high resistance to autoignition. Distinct combustion modes are present: the DI fuel auto-ignites following chemical ignition delay after spray vaporization and mixing; a reactive front is formed on its surroundings; it develops into a well-structured turbulent flame, which propagates within the premixed charge. Either direct chemistry or the flame-propagation approach (G- Equation), taken alone, do not produce accurate results. The proposed Dual-Fuel model decides what regions of the combustion chamber should be simulated with either approach, according to the local flame state; and acts as a “kernel” model for the G- Equation model. Direct chemistry is run in the regions where a premixed front is not present.

The present paper reports experimental and numerical research activities devoted to deeply characterize the behavior and performance of a Heavy Duty (HD) internal combustion engine fed by compressed natural gas (CNG). Current research interest in HD engines fed by gaseous fuels with low C/H ratios is related to the well-known potential of such fuels in reducing carbon dioxide emissions, combined to extremely low particulate matter emissions too. Moreover, methane, the main CNG component, can be produced through alternative processes relying on renewable sources, or in the next future replaced by methane/H2 blends. The final goal of the presented investigations is the development of a predictive 0D combustion submodel within the framework of a 1D numerical simulation platform.

This paper presents a preliminary study to estimate, using on-road and laboratory tests, the mileage range of liquefied petroleum gas (LPG) as an alternative fuel for diesel-fed public utility jeepneys in the Philippines. Data from the study would be used by the Philippine Department of Energy to formulate and implement alternative fuel programs for public transport. On-road fuel consumption, load factor, and GPS speed data from selected in-use LPG and diesel jeepneys plying a chosen urban route were gathered to develop corresponding drive cycles for chassis dynamometer testing at 100% load factor were conducted to estimate an upper limit for fuel consumption. Measured on-road diesel jeepney mileage was about 6.7 km/liter at 63.5% load factor while that for LPG jeepney was 3.8-4.2 km/liter at 59.8% load factor. Drive cycle tests yielded 5.2 km/liter for diesel and 2.6-3.1 km/liter for LPG.

For over a decade engine manufacturers have been pursuing alternative fuel strategies for vehicle powertrains. First came the discussion of fuel selection. Next, whether or not these alternative fuels can provide the utility offered by traditional diesel. Finally, the footrace of technology and hardware to provide utility, reliability and maintainability with the use of alternative fuels. Now the day has come where many alternative fuels are a practical reality. The body of this paper will discuss the utilization of natural gas as an alternative fuel. This paper targets the fleet operator in an effort to provide a single source of information in a concise format. A discussion of emission standards, engine operational strategies, component technology, fuel characteristics and the utility of using natural gas as a fuel will be addressed. The understanding of present and future engine development is of great importance to a successful fleet operation.

Exhaust gas recirculation (EGR) is a suitable strategy to optimize heavy duty natural gas (NG) engines. EGR could be utilized to have high specific power, with low thermal stress, but also to increase engine efficiency. NG fuelling permits a large flexibility in EGR system design, due to very clean engine exhaust. In this paper, three types of EGR routes have been studied. The best set up, which can introduce the highest EGR quantities, to provide the best reduction of the thermal load at rated power, was found to be a cooled low pressure EGR route. However high low pressure route (HLPR) could give the possibility to increase engine efficiency by modulating the power output in the widest un-throttled range operation.

The West Virginia University (WVU) Transportable Heavy-Duty Vehicle Emissions Testing Laboratory was employed to conduct chassis dynamometer tests in the field to measure the exhaust emissions from heavy-duty buses and trucks. This laboratory began operation in the field in January, 1992. During the period January, 1992 through June, 1993, over 150 city buses, trucks, and tractors operated by 18 different authorities in 11 states were tested by the facility. The tested vehicles were powered by 14 different types of engines fueled with natural gas (CNG or LNG), methanol, ethanol, liquified petroleum gas (LPG), #2 diesel, and low sulfur diesel (#1 diesel or Jet A). Some of the tested vehicles were equipped with exhaust after-treatment systems. In this paper, a total of 12 CNG-fueled and #2 diesel-fueled transit buses equipped with Cummins L-10 engines, were chosen for investigation.

Due to stringent emission standards, the demand for higher efficiency engines has been unprecedentedly high in recent years. Among several existing combustion modes, pre-chamber spark ignition (PCSI) emerges to be a potential candidate for high-efficiency engines. Research on the pre-chamber concept exhibit higher indicated efficiency through lean limit extension while maintaining the combustion stability. In this study, a unique pre-chamber geometry was tested in a single-cylinder heavy-duty engine at low load lean conditions. The geometry features a narrow throat, which was designed to be packaged inside a commercial diesel injector pocket. The pre-chamber was fueled with methane while the main chamber was supplied with an ethanol/air mixture.

Machine learning models were shown to provide faster results but with similar accuracy to multidimensional computational fluid dynamics or in-depth experiments. This study used a support-vector machine (SVM), a set of related supervised learning methods, to predict the dynamic performance (i.e., engine power and torque) of a heavy-duty natural gas spark ignition engine. The single-cylinder four-stroke test engine was fueled with methane. The engine was operated at different spark timings, mixture equivalence ratios, and engine speeds to provide the data for training and testing the proposed SVM. The results indicated that the performance and accuracy of the built regression model were satisfactory, with correlation coefficient quantities all larger than 0.95 and root-mean-square errors close to zero for both training and validation datasets.

This report details the experiences of two California public transit agencies that replaced aging diesel buses with new compressed natural gas (CNG) buses in 1994. The operating characteristics and costs of 170 natural gas buses are compared with 73 older diesel buses. The natural gas bus fleets have operated well and led to cost reductions in both fleets. The findings are particularly significant because both Sacramento Regional Transit District (RT) and SunLine Transit Agency have been using the same engine-chassis configuration, thus enabling a valid method to combine cost data for a large sample fleet of buses. The data indicate that labor for diesel equipment was almost twice that for CNG vehicles, parts were 25% more and fuel costs were nearly double. In 1997, CNG buses saved RT over $1 million in fuel, maintenance, parts and hazardous waste disposal, a 38% per mile reduction over the cost of their older diesel buses.

Abstract In order to meet upcoming emission targets, an increasing number of ships using Liquefied Natural Gas (LNG) as fuel have been put into service. In this context, many shipowners are particularly interested in the dual-fuel (DF) large-engine technology, which enables ships to operate with both gaseous and conventional liquid fuels. The use of different combustion principles in DF engines requires a layout of the base engine with a relatively low compression ratio (CR) for the gas mode to prevent unstable combustion (knocking). However, this layout leads to disadvantages in the Diesel operation mode, which requires a higher CR for optimal fuel efficiency. Therefore, a two-stage variable compression ratio (VCR) system is a technology particularly suitable for DF engines. It allows to reduce fuel costs by approximately 5.5%.

It is projected that even when the entire on-road fleet of heavy-duty vehicles operating in California is compliant with 2010 emission standards of 0.20 g/bhp-hr, the National Ambient Air Quality Standards (NAAQS) requirements for ambient ozone will not be met. It is expected that further reductions in NOX emissions from the heavy-duty fleet will be required to achieve compliance with the ambient ozone requirement. To study the feasibility of further reductions, the California Air Resources Board (CARB) funded a research program to demonstrate the potential to reach 0.02 g/bhp-hr NOX emissions. This paper details the work executed to achieve this goal on the heavy-duty Federal Test Procedure (FTP) with a heavy-duty natural gas engine equipped with a three-way catalyst. A Cummins ISX-12G natural gas engine was modified and coupled with an advanced catalyst system.

Recently conducted work has been funded by the California Air Resources Board (CARB) to explore the feasibility of achieving 0.02 g/bhp-hr NOX emissions for heavy-duty on-road engines. In addition to NOX emissions, greenhouse gas (GHG), CO2 and methane emissions regulations from heavy-duty engines are also becoming more stringent. To achieve low cold-start NOX and methane emissions, the exhaust aftertreatment must be brought up to temperature quickly while keeping proper air-fuel ratio control; however, a balance between catalyst light-off and fuel penalty must be addressed to meet future CO2 emissions regulations. This paper details the work executed to improve catalyst light-off for a natural gas engine with a close-coupled and an underfloor three-way-catalyst while meeting an FTP NOX emission target of 0.02 g/bhp-hr and minimizing any fuel penalty.

In the recent years, the interest in heavy-duty engines fueled with Compressed Natural Gas (CNG) is increasing due to the necessity to comply with the stringent CO2 limitation imposed by national and international regulations. Indeed, the reduced number of carbon atoms of the NG molecule allows to reduce the CO2 emissions compared to a conventional fuel. The possibility to produce synthetic methane from renewable energy sources, or bio-methane from agricultural biomass and/or animal waste, contributes to support the switch from conventional liquid fuels to CNG. To drive the engine development and reduce the time-to-market, the employment of numerical analysis is mandatory. This requires a continuous improvement of the simulation models toward real predictive analyses able to reduce the experimental R&D efforts. In this framework, 1D numerical codes are fundamental tools for system design, energy management optimization, and so on.

The paper presents a novel concept of a very efficient transportation engines for operation with CNG, LNG or LPG. The paper considers the options of single fuel design with jet ignition and dual fuel design with Diesel and gas. In the first option gas fuel is injected into the main chamber by a direct injector and ignited by jet ignition. In the second option gas fuel is injected into the main chamber by a direct injector and ignited by the direct injection of a small quantity of Diesel fuel. Injection and ignition may be tuned to control the amount of premixed and diffusion combustion to produce the best fuel conversion efficiency vs. load and speed requirements within the prescribed pressure and temperature constraints.