Search Results

Abstract Regulations limiting GreenHouse Gases (GHG) from Heavy-Duty (HD) commercial vehicles in the United States (US) and European Union will phase in between the 2024 and 2030 model years. These mandates require efficiency improvements at both the engine and vehicle levels, with the most stringent reductions required in the heaviest vehicles used for long-haul applications. At the same time, a 90% reduction in oxides of nitrogen (NOx) will be required as part of new regulations from the California Air Resources Board. Any technologies applied to improve engine efficiency must therefore not come at the expense of increased NOx emissions. Research into advanced engine architectures and components has identified improved turbomachine efficiency as one of the largest potential contributors to engine efficiency improvement. However this comes at the cost of a reduced capability to drive high-pressure Exhaust Gas Recirculation (EGR).

In the truck industry there is a continuous demand to increase the efficiency and to decrease the emissions. To acknowledge both these issues a waste heat recovery system (WHR) is combined with a partially premixed combustion (PPC) engine to deliver an efficient engine system. Over the past decades numerous attempts to increase the thermal efficiency of the diesel engine has been made. One such attempt is the PPC concept that has demonstrated potential for substantially increased thermal efficiency combined with much reduced emission levels. So far most work on increasing engine efficiency has been focused on improving the thermal efficiency of the engine while WHR, which has an excellent potential for another 1-5 % fuel consumption reduction, has not been researched that much yet. In this paper a WHR system using a Rankine cycle has been developed in a modeling environment using IPSEpro.

A correlation study of vehicle exhaust emissions measurements was conducted by the West Virginia University (WVU) Transportable Heavy-Duty Vehicle Emissions Testing Laboratory and the Los Angeles County Metropolitan Transportation Authority (MTA) Emissions Testing Facility. A diesel fueled transit bus was tested by both chassis dynamometer emissions testing laboratories. Exhaust emissions were sampled from the tested vehicle during the operation of the Federal Transit Administration (FTA) Central Business District (CBD) testing cycle. Data of gaseous and particulate matter emissions was obtained at each testing laboratory. The emissions results were compared to evaluate the effects of different equipment, test procedures, and drivers on the measurements of exhaust emissions of heavy-duty vehicles operated on a chassis dynamometer.

Emissions from heavy-duty diesel vehicles have come under increased scrutiny with passage of the U.S. Clean Air Act Amendments of 1990. Methanol (M100) is seen as an important option for operators of transit fleets given the fuel's liquid nature and relative availability. This paper presents the results of a 36-month demonstration of a fleet of six methanol-powered transit buses equipped with DDC 6V-92TA engines. The engines were delivered in 1991 and were the first batch of Detroit Diesel engines certified to meet 1991 clean air standards. A similarly equipped control fleet of six diesel buses was tracked simultaneously. This paper includes an evaluation of bus operating data and emissions. Data such as fuel and oil consumption were collected along with a complete list of maintenance actions on both fleets. Chassis dynamometer emissions testing was carried out by Environment Canada at their River Road (Ottawa) test facility.

The authors used a mass spectrometer to determine an SOF reduction mechanism of a diesel oxidation catalyst. The results indicate that SOF reduction lies in the catalytic conversion of high molecular organic matter to low molecular organic matter. And unregulated emissions are also reduced through this conversion. It is also found that the SOF reduction performance is highly dependent up on the condition of the wash coat. There is some limitation to improving diesel oxidation catalyst performance because of the sulfur content found in diesel fuel. Finally, the authors have determined what we think are the specifications of the presently best catalytic converter.

Stringent global emissions legislations demand effective NOx reduction strategies for both the engine as well as the aftertreatment. Diesel applications have previously applied Lean NOx Catalysts (LNCs) [1, 2], but their reduction efficiency and longevity have been far less than that of the competing ammonia-based SCR systems, such as urea [3]. A catalyst has been developed to significantly reduce NOx emissions, approaching 60% with ULSD and exceeding 95% with E85. Both thermal and sulfur aging are applied, as well as on-engine aging, illustrating resilient performance to accommodate necessary life requirements. A robust system is developed to introduce both ULSD from the vehicle's tank as well as E85 (up to 85% ethanol with the balance being gasoline) from a moderately sized supplemental tank, enabling extended mileage service intervals to replenish the reductant, as compared with urea, particularly when coupled with an engine-out based NOx reduction technology, such as EGR.

This paper describes recent progress in our program to develop an emissions technology allowing diesel engines to meet the upcoming 2007/2010 regulations for NOx. At the heart of this technology is the ArvinMeritor Diesel Fuel Reformer that reforms the fuel, on-demand, on-board a vehicle. The fuel reformer uses plasma to partially oxidize a mixture of diesel fuel and air creating a highly reducing mixture of Hydrogen and Carbon monoxide. In a previous publication, we have demonstrated that using a reformate rich in H2 and CO to regenerate a NOx trap is highly advantageous compared to vaporized diesel fuel used conventionally. In this paper we present results and a strategy for performing desulfation of the traps using the fuel reformer. In contrast to vaporized diesel, which requires very high temperatures that fall outside the normal exhaust operating temperatures for diesel engines, desulfation was achieved at temperatures lower by more than 100 °C using the Plasma Fuel Reformer.

A 13 L HD diesel engine was converted to run as a flame propagation engine using the HEDGE™ Dual-Fuel concept. This concept consists of pre-mixed gasoline ignited by a small amount of diesel fuel - i.e., a diesel micropilot. Due to the large bore size and relatively high compression ratio for a pre-mixed combustion engine, high levels of cooled EGR were used to suppress knock and reduce the engine-out emissions of the oxides of nitrogen and particulates. Previous work had indicated that the boosting of high dilution engines challenges most modern turbocharging systems, so phase I of the project consisted of extensive simulation efforts to identify an EGR configuration that would allow for high levels of EGR flow along the lug curve while minimizing pumping losses and combustion instabilities from excessive backpressure. A potential solution that provided adequate BTE potential was consisted of dual loop EGR systems to simultaneously flow high pressure and low pressure loop EGR.

There is potential to reduce GHG emissions in the HDV sector through different powertrain options (electric batteries, fuel cell batteries, and combustion engines), and different fuel or energy choices (hydrogen, biofuels, natural gas). The climate impacts of these technologies and fuels vary over the lifetime of the vehicle model. From extracting and processing raw materials to operation and maintenance, some powertrain options are more energy intensive to build than their counterparts, and some fuel sources can produce higher emissions during their production or use. The study uses a life-cycle assessment to analyze the options to allow policymakers and manufacturing companies to compare which powertrain and fuel options provide the largest GHG emissions reductions.

Biofuel can enable a sustainable transport solution and lower greenhouse gas emissions compared to standard fuels. This study focuses on biodiesel, implemented in the easiest way as drop in fuel. When mixing biodiesel into diesel one can run into problems with solubility causing contaminants precipitating out as insolubilities. These insolubilities, also called soft particles, can cause problems such as internal injector deposits and nozzle fouling. One way to overcome the problem of soft particles is by filtration. It is thus of great interest to be able to quantify fuel filters’ ability to intercept soft particles. The aim of this study is to test different fuel filters for heavy-duty engines and their ability to filter out synthetic soft particles. A custom-built fuel filter rig is presented, together with some of its general design requirements. For evaluation of the efficiency of the filters, fuel samples were taken before and after the filters.

As a result of the Kyoto Protocol [1], the European Union's legislation demands higher saving rates for the total energy consumption of technical equipment. Heavy Equipment, such as construction- and agricultural machines, contributes over 80% of the total off-road diesel fuel consumption in Germany per annum. It is therefore necessary to provide helpful solutions in order to reach this ambitious aim. The German Federal Ministry of Education and Research cooperates with machine manufacturers, component suppliers and research institutes in the area of heavy equipment. Under the project name TEAM [2] a three year project has been started, which is focused on the development and integration of new propulsion and steering systems for heavy equipment. One task within the project is finding an appropriate way of evaluating the energy efficiency of the enhanced machines, after the powertrain modifications have been applied to it.

An organic Rankine Bottoming cycle added to Diesel engines used for long-haul trucks has the potential of improving their peak fuel economy by up to 15% over a typical duty cycle. General Electric has developed a multi-vane rotary expander which has a measured isentropic brake efficiency of 80+% over a wide range of speed and power levels with organic working fluids. High cycle efficiency for design and off-design conditions is achieved with the multi-vane expander. The potential advantages of the multi-vane expander for the Diesel engine bottoming cycle include the elimination of a high speed gear box and the potential for over 80% isentropic engine efficiency. The multi-vane expander is a ruggedly built component running at Diesel engine speed. This paper describes the design and evaluation of a nominal 40 HP multi-vane expander for this application.

A combustion system has been developed to burn neat (pure) methanol in a direct-injection four-stroke-cycle engine. Primary objectives were to obtain low fuel consumption and long component life to make the engine suitable to replace heavy-duty diesel fueled engines. A glow plug was placed in a modified quiescent combustion chamber to ensure reliable methanol ignition at all engine operating conditions. The methanol engine provides thermal efficiency nearly equal to the diesel engine from which it is derived, in addition, nitrogen oxide emissions are reduced by 50 percent and exhaust smoke is negligible. Hydrocarbon emissions are still above the baseline diesel engine. Laboratory and field durability tests of over 2000 hours have been completed. Excellent cold-start capability has been established.

The internal combustion engines emit combustion gases which contain nano and micrometric particles that are harmful to human health, causing deleterious damages to the human's respiratory system. In Brazil, heavy vehicles, such as buses and trucks, have diesel engines that work under high loads and run through metropolitan areas or in intense traffic flow roads. They are considered, nowadays, the main solid particles emitter in several World's areas. There are already standard systems to analyze these particles quantitative and qualitatively at high prices collected from vehicle gases emissions in places such as bus stops. This paper presents a new method which retains solid micrometric particulate matter emitted by diesel engine. It is simple and has a relatively low cost. A sheet of textile element was encapsulated in a system for gripping micrometric particles emitted by diesel single-cylinder engine operating in a bench and coupled with a electrical generator.

For the purpose of developing direct injection heavy-duty methanol engines which surpass diesel engines in purformace, this paper first clarifies the methanol concentration around the spark plug for achieving a high ignition stability by sampling the gas near the spark plug using a sampling valve. The combustion process of methanol is then observed by the method of high-speed Schlieren photography to clarify the mode of methanol combustion. A new methanol DISC combustion system having a protrusion in the combustion chamber is devised based on such results. This study clarifies that the methanol concentration at the point of ignition for high ignition stability is in the range of 6 to 22 vol%. The methanol mixture burns by flame propagation so far as the compression ratio is on the order of 16.5.

The performance of five positive k-factor injector tips has been assessed in this work by analyzing a comprehensive set of injected mass, momentum, and spray measurements. Using high speed shadowgraphs of the injected diesel plumes, the sensitivities of measured vapor penetration and dispersion to injection pressure (100-250MPa) and ambient density (20-52 kg/m3) have been compared with the Naber-Siebers empirical spray model to gain understanding of second order effects of orifice diameter. Varying in size from 137 to 353μm, the orifice diameters and corresponding injector tips are appropriate for a relatively wide range of engine cylinder sizes (from 0.5 to 5L). In this regime, decreasing the orifice exit diameter was found to reduce spray penetration sensitivity to differential injection pressure. The cone angle and k-factored orifice exit diameter were found to be uncorrelated.

Today’s growing commercial vehicle population creates a demand for fossil fuel surplus requirement and develops highly polluted urban cities in the world. Hence addressing both factors is very much essential. Battery electric vehicles are with limited vehicle range and higher charging time. So it is not suitable for the long-haul application. In further the hydrogen fuel cell-based electric vehicles are the future of the commercial electric vehicle to achieve long-range, zero-emission and alternate for reducing fossil fuels requirement. The hydrogen fuel cell electric vehicle range, it means the total distance covered by the vehicle in a single filling of hydrogen into the onboard cylinders. And here the prediction of the vehicle range is essential based on optimal parameters; vehicle acceleration, speed, trip time etc. before the start of the trip.

Abstract Due to the incoming phase out of fossil fuels from the market in order to reduce the carbon footprint of the automotive sector, hydrogen-fueled engines are candidate mid-term solution. Thanks to its properties, hydrogen promotes flames that poorly suffer from the quenching effects toward the engine walls. Thus, emphasis must be posed on the heat-up of the oil layer that wets the cylinder liner in hydrogen-fueled engines. It is known that motor oils are complex mixtures of a number of mainly heavy hydrocarbons (HCs); however, their composition is not known a priori. Simulation tools that can support the early development steps of those engines must be provided with oil composition and properties at operation-like conditions. The authors propose a statistical inference-based optimization approach for identifying oil surrogate multicomponent mixtures. The algorithm is implemented in Python and relies on the Bayesian optimization technique.

The objective of this study was to evaluate iso-butanol (C4H9OH) as an alternative fuel for spark ignition engines. Unlike methanol (CH3OH) and ethanol (C2H5OH), iso-butanol has not been extensively studied in the past as either a fuel blend candidate with gasoline or straight fuel. The performance of a single cylinder engine (ASTM=CFR) was studied using alcohol-gasoline blends under different input parameters. The engine operating conditions were: three carburetor settings (three different fuel flow rates), spark timings of 5°, 10°, 15°, 20°, and 25° BTDC, and a range of compression ratios from a minimum of 7.5 to a maximum of 15 in steps of one depending on knock. The fuels tested were alcohol-gasoline blends having 5%, 10%, 15%, and 20% of iso-butanol, ethanol, and methanol. And also as a baseline fuel, pure gasoline (93 ON) was used. The engine was run at a constant speed of 800 RPM.

Waste heat recovery (WHR) has been recognized as a promising technology to achieve the fuel economy and green house gas reduction goals for future heavy-duty (HD) truck diesel engines. A Rankine cycle system with ethanol as the working fluid was developed at AVL Powertrain Engineering, Inc. to investigate the fuel economy benefit from recovering waste heat from a 10.8L HD truck diesel engine. Thermodynamic analysis on this WHR system demonstrated that 5% fuel saving could be achievable. The fuel economy benefit can be further improved by optimizing the design of the WHR system components and through better utilization of the available engine waste heat. Although the WHR system was designed for a stand-alone system for the laboratory testing, all the heat exchangers were sized such that their heat transfer areas are equivalent to compact heat exchangers suitable for installation on a HD truck diesel engine.