Search Results

Research has been conducted on Controlled Auto-Ignition (CAI) engine with natural gas. CAI engine has the potential to be highly efficient and to produce low emissions. CAI engine is potentially applicable to automobile engine. However due to narrow operating range, CAI engine for automobile engine which require various speed and load in real world operation is still remaining at research level. In comparison some natural gas engines for electricity generation only require continuous operation at constant load. There is possibility of efficiency enhancement by CAI combustion which is running same speed at constant load. Since natural gas is primary consisting of methane (CH4), high auto-ignition temperature is required to occur stable auto-ignition. Usually additional intake heat required to keep stable auto-ignition. To keep high compression temperature, single cylinder natural gas engine with high compression ratio (CR=26) was constructed.

Four forces act in rings for a metal pushing V-belt. These forces are: two kinds of intercepting forces which prevent blocks from going outside of pulleys (one caused by pulley thrust, the other caused by centrifugal force), frictional force acting between the rings and the blocks, and bending force in longitudinal direction. In the previous paper (1)(2)(3)(5), distribution of three forces, excluding centrifugal force, were presented at low belt speed. We successfully measured all four kinds of forces including centrifugal force continuously at practical operation conditions for layered rings. In this paper, distribution of these four forces on the innermost ring is described at steady states.

In this study, distributions of block compression force on the driving and driven pulleys were measured using a tiny load-cell inserted between two blocks and a telemeter system, under several constant speed ratios. Ring tension distributions were also measured using a specially devised block. From the experimental results, the following conclusions were drawn: (1) Block compression force distribution on the driving pulley is significantly different from that on the driven pulley. (2) Ring tension takes different value at each side of strings. It is considered that this phenomenon is caused by difference of saddle surface speed between two pulleys.

A model of a timing belt analyzed by FEM (a general non-linear finite element program:ABAQUS) successfully confirmed the mechanism that generates belt cord stress. Analysis revealed a good correlation between the experimental and computed results of stress distribution of the belt cord. Through calculation, it was discovered that belts broke near the tooth root, which is the point of maximum stress of the cord.

Combined Brake System for small motorcycles has been developed. In small motorcycles, some models have a hydraulic disc brake both in the front and rear wheels but many of them have a hydraulic disc front brake and a mechanical drum rear brake. Accordingly, it was necessary to develop a new system to link the hydraulic system with the mechanical system to allow an application of Combined Brake System to these models. In this paper, a CBS having a new configuration is described where a disc brake and a drum brake are linked in a simple lever structure of an input force distributor, and an inhibitor spring at the foot pedal. With this mechanism equipped, the distribution of brake forces is controlled. When a large input force is applied, a large proportion of brake force is applied to the front brake to obtain adequate deceleration. When a mild input force is applied, which is frequently operated, the brake force proportion is large in the rear compared to the front.

Gasoline includes various kinds of chemical species. Thus, the reaction model of gasoline components that includes the low-temperature oxidation and ignition reaction is necessary to investigate the method to control the combustion process of the gasoline engine. In this study, a gasoline combustion reaction model including n-paraffin, iso-paraffin, olefin, naphthene, alcohol, ether, and aromatic compound was developed. KUCRS (Knowledge-basing Utilities for Complex Reaction Systems) [1] was modified to produce paraffin, olefin, naphthene, alcohol automatically. Also, the toluene reactions of gasoline surrogate model developed by Sakai et al. [2] including toluene, PRF (Primary Reference Fuel), ethanol, and ETBE (Ethyl-tert-butyl-ether) were modified. The universal rule of the reaction mechanisms and rate constants were clarified by using quantum chemical calculation.

Using sand cores, the weld-able, hollow die-cast parts have been developed. For casting, the transition flow filling method is applied to reduce gas containment and to minimize damages to the core. In designing the products, the newly developed core stress prediction system by melt pressure distribution and the newly developed in-product gas containment prediction system have been applied. The hollow die-cast frame made by the new method attains a 30% increase in rigidity and 1kg reduction of weight.

A new hydrogen fueling protocol named MC Formula Moto was developed for fuel cell motorcycles (FCM) with a smaller hydrogen storage capacity than those of light duty FC vehicles (FCV) currently covered in the SAE J2601 standard (over than 2kg storage). Building on the MC Formula based protocol from the 2016 SAE J2601 standard, numerous new techniques were developed and tested to accommodate the smaller storage capacity: an initial pressure estimation using the connection pulse, a fueling time counter which begins the main fueling time prior to the connection pulse, a pressure ramp rate fallback control, and other techniques. The MC Formula Moto fueling protocol has the potential to be implemented at current hydrogen stations intended for fueling of FCVs using protocols such as SAE J2601. This will allow FCMs to use the existing and rapidly growing hydrogen infrastructure, precluding the need for exclusive dispensers or stations.

This paper discusses a method of predicting the torque distribution on planet gears originating in manufacturing errors, which is necessary for appropriate strength design of the gears in planetary gear sets. First, an expression of relation between manufacturing errors and the torque on the planet gears in a normal n-planet planetary gear set was derived. As a result, an equation expressing the distribution of torque to the planet gears was obtained. Tests were conducted to verify the validity of the equation in the case of a 4-planet planetary gear set. In order to predict the distribution of torque, it was necessary to estimate the stiffness of the planetary gear set that was the subject of the relational expression. These stiffness values were calculated by numerical analysis using a 3D FEM, into which blueprint values and material property values were input.

Nd₂Fe₁₄B sintered magnets are used in the drive motors of hybrid, electric and other vehicles. A magnet in which rare earth content is reduced by means of a localized diffusion method has been developed in order to reduce the volume of dysprosium. The distribution of the demagnetization fields in a motor is not uniform, so the necessary coercivity distribution for the magnets was quantified using Computer-Aided Engineering (CAE). Then material specifications of the localized dysprosium diffusion satisfied with this coercivity distribution was determined, and optimal manufacturing conditions including the position of dysprosium diffusion were set. The coercivity distribution in every position of the magnet using localized diffusion method was inspected. As a result, the magnet was satisfied with coercivity distribution demanded by CAE.

This paper describes the development of non-contacting detection type torque sensor that realizes a small lost motion with light weight and low cost. Pedal-equipped electric vehicles are becoming popular in recent years. In those vehicles, torque sensors are usually necessary for measuring the pedaling force to determine the motor torque. We applied an integrated sensing structure and a non-contacting scheme utilizing inverse-magnetostrictive material to minimize the lost motions. As for the sensing material, nickel-iron alloy plating was used to obtain a wide dynamic range. In the tests using the actual structure, the output linearity deterioration occurred because of the strain distribution dispersion produced by the ratchet drive structure. Therefore, the effect of this strain distribution was examined. The inverse-magnetostrictive sensing material of nickel-iron alloy plating has an extremum on its output curve.

A highly efficient two-motor plug-in hybrid system is developed to satisfy the global demands of CO2 reduction. This system switches three operation modes, what is called “EV Drive”, “Hybrid Drive” and “Engine Drive”, to maximize fuel efficiency according to the driving condition of the vehicle. Practical plug-in EV (Electric Vehicle) capability is also realized by adding a high-power on-board charger and a high capacity Li-ion battery to the original system. The outlines of the system components including a newly developed Atkinson cycle engine, a highly efficient electric coupled CVT (Continuously Variable Transmission) with built-in motor and generator, an integrated PCU (Power Control Unit) and an exclusive battery for plug-in HEV (Hybrid Electric Vehicle) are described in this paper. In addition to the switching of three driving modes and the efficiency improvement of each device, cooperative control of the hybrid system is introduced.

This paper explains the new methodology for post-crash fuel leakage testing of Fuel Cell Vehicles (FCVs) and other hydrogen vehicles utilizing compressed hydrogen storage systems. This methodology was incorporated into SAE J2578 that was revised and published in January, 2009. The new methodology is based on the concept in FMVSS 303 that specifies post-crash fuel leakage test method and criteria for CNG vehicle and adopted some modifications. Specifically, the following items are addressed: (1) Allowable leakage can be accurately evaluated in test even with large size tank that obtains only small pressure drop when a given amount of leakage occurs. A new method to deal with the influence of measurement errors was devised. (2) Even though only one option of test gas and initial filling pressure is accepted in FMVSS 303, new methodology for hydrogen system allows helium and hydrogen at reduced pressure as alternatives in addition to hydrogen at service pressure.

In this study, in order to relax the pre-cooling regulations at hydrogen fueling stations, we develop a software algorithm to simulate an actual hydrogen fueling process to Fuel Cell Vehicle (FCV) tanks. The simulation model in the software consists of the same filling equipment found at an actual hydrogen fueling station. Additionally, the same supply conditions (pre-cooling temperature, pressure and mass flow rate) as at a hydrogen fueling station were set to the simulation model. Based on the supply conditions, the software simulates the temperature and pressure of hydrogen in each part of filling equipment. In order to verify the accuracy of the software, we compare the temperature and pressure simulated at each stage of the filling process with experimental data. We show that by using the software it is possible to accurately calculate the hydrogen temperature and pressure at each point during the fueling process.

The present study experimentally investigated the performance and emission characteristics of the diesel engine with hydrogen added to the intake air at late diesel-fuel injection timings. The diesel-fuel injection timing and the hydrogen fraction in the intake mixture were varied while the gross heating value per second of diesel fuel and hydrogen was kept constant at a certain value. NO showed minimum at specific hydrogen fraction. The maximum rate of incylinder pressure rise also showed minimum at 10 vol% hydrogen fraction. The indicated thermal efficiency was almost constant or slightly increased with small amount of hydrogen. A combination of hydrogen addition and late diesel-fuel injection timing contributed to low temperature combustion, in which NO decreased without the increase in unburned fuel.

Compression ignition combustion with a lean mixture has high potential in terms of high theoretical thermal efficiency and low NOx emission characteristics due to low combustion temperatures. In particular, a Dual-Fuel concept is proposed to achieve high ignition timing controllability and an extended operation range. This concept controls ignition timing by adjusting the fraction of two fuels with different ignition characteristics. However, a rapid combustion process after initial ignition cannot be avoided due to the homogenous nature of the fuel mixture, because the combustion process depends entirely on the high reaction rate of thermal ignition. In this study, the effect of mixture stratification in the cylinder on the combustion process after ignition based on the Dual-Fuel concept was investigated. Port injection of one fuel creates the homogeneous mixture, while direct injection of the other fuel prepares a stratified mixture in the cylinder at the compression stroke.

In this research, a new wire material made using surface-reforming heat treatment was developed in order to enhance the corrosion fatigue resistance of suspension springs. The aim of surface reforming is to improve hydrogen embrittlement characteristics through grain refinement and to improve crack propagation resistance by partial softening of hardness. The grain refinement method used an α'→γ reversed transformation by rapid short-term heating in repeated induction heating and quenching (R-IHQ) to refine the crystal grain size of SAE 9254 steel spring wire to 4 μm or less. In order to simultaneously improve the fatigue crack propagation characteristics, the possibility of reducing the hardness immediately below the spring surface layer was also examined. By applying contour hardening in the second IHQ cycle, a heat affected zone (HAZ) is obtained immediately below the surface.

The present study experimentally investigated cyclic variation of combustion characteristics of a diesel engine with hydrogen added to the intake air in detail. As the result, there were three ignition modes: (1) hydrogen ignition mode, (2) hydrogen-assisted ignition mode, and (3) diesel-fuel ignition mode. Ignition timing fluctuated from cycle to cycle in each ignition mode and between one ignition mode and another mode. As the coolant temperature was increased, the number of cycles in diesel-fuel ignition mode decreased, and indicated thermal efficiency and cyclic variation was improved. In the case with the blow-by gas introduced to intake port, preflame reaction of blow-by gas first occurred, ignited hydrogen, and then diesel-fuel was ignited by hydrogen combustion in hydrogen ignition mode and hydrogen-assisted ignition mode.

The process for setting the marketability targets and achievement methods for automotive interior quietness (as related to air borne noise above 400Hz, considered the high frequency range) was established. With conventional methods it is difficult to disseminate the relationship between the performance of individual parts and the overall vehicle performance. Without new methods, it is difficult to propose detailed specifications for the optimal sound proof packages. In order to make it possible to resolve the individual components performance targets, the interior cavity was divided into a number of sections and the acoustic performance of each section is evaluated separately. This is accomplished by evaluating the acoustical energy level of each separate interior panel with the unit power of the exterior speaker excitation. The applicability of the method was verified by evaluating result against predicted value, using the new method, during actual vehicle operation.

This paper describes an effective method with statistical energy analysis (SEA) for specifying the vehicle sound proof package that achieves the best balance between light weight and high sound insulation performance. For proposing the sound proof package in the early stages of vehicle development, it is necessary to assess a number of specifications and to pick the best design specifications for weight and sound proof performance. However, there are difficulties in achieving conflicting objectives simultaneously, and acoustic engineers need special technical know-how. In this study, a new automated optimization method is proposed that approaches the problem above. As a result, detailed sound insulation package specifications, including the thickness distribution of each part, can be obtained and these can be easily transferred to drawings. Moreover, the accuracy of this method is proven by a reduction in vehicle interior cabin sound pressure level