Standard
280 RELAY FOOTPRINT
1994-06-01
CURRENT
J1744_199406
This SAE Standard covers a terminal footprint for mini and micro relays used in surface vehicle electrical systems.
Search Results
Standard
6- AND 12-VOLT CIGAR LIGHTER SWITCH BASES
1960-01-01
HISTORICAL
J563_196001
Standard
ABRASION RESISTANCE TESTING—VEHICLE EXTERIOR GRAPHICS AND PIN STRIPING
1989-06-01
HISTORICAL
J1847_198906
This SAE Recommended Practice applies to the abrasion resistance testing of decorative tapes, graphics, and pin striping. It may also have relevance to certain vehicle labels and plastic wood grain film. The resistance to abrasive damage is judged qualitatively by its effect on the legibility, pattern, and color of the graphic marking. This recommended practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering the use of this recommended practice.
Standard
ABRASIVE WEAR
1966-08-01
HISTORICAL
J965_196608
An enormous economic loss, as well as a waste of natural resources, is incurred world-wide as a result of wear of components and tools. Any effort expended in an attempt to reduce this loss is indeed worthwhile. The purpose of this SAE Information Report is to present the current state of knowledge of abrasive wear. This report, therefore, covers wear, or the undesired removal of metal by mechanical action, caused by abrasive particles in contact with the surface. It does not concern metal-to-metal wear or wear in the presence of an abrasive free lubricant. Abrasive wear occurs when hard particles, such as rocks, sand, or fragments of certain hard metals, slide or roll under pressure across a surface. This action tends to cut grooves across the metal surface, much like a cutting tool. Abrasive wear is of considerable importance in any part moving in relation to an abrasive.
Standard
ACCESS SYSTEMS FOR CONSTRUCTION AND INDUSTRIAL EQUIPMENT
1970-07-01
HISTORICAL
J185_197007
This recommended practice covers the criteria for steps, ladders, walkways, platforms, grab rails (handrails), grab irons, guardrails, and entrance openings as they relate to aiding the operator and/or servicemen in performing their functions on the vehicle.
Standard
AUTOMATIC SLACK ADJUSTER PERFORMANCE REQUIREMENTS
1985-06-01
HISTORICAL
J1513_198506
These performance requirements have been established for automatic slack adjusters when tested to SAE J1462, Automatic Slack Adjuster Test Procedure.
Standard
AUTOMOTIVE DUCTILE (NODULAR) IRON CASTINGS
1986-06-01
HISTORICAL
J434_198606
This SAE Standard covers the hardness and microstructure requirements for ductile iron castings used in automotive and allied industries. Castings may be specified in the as-cast or heat treated condition. The Appendix provides general information on the application of ductile iron castings and their chemical composition to meet hardness microstructure and other properties needed for particular service conditions. The mechanical properties in the Appendix are provided for design purposes.
Standard
AUTOMOTIVE FLASHER TEST EQUIPMENT
1962-04-01
HISTORICAL
J823_196204
The purpose of this SAE Standard is to specify the test circuitry and instruments required for determining the performance of automotive flashers.
Standard
AUTOMOTIVE FLASHER TEST EQUIPMENT
1965-07-01
HISTORICAL
J823A_196507
The purpose of this SAE Standard is to specify the test circuitry and instruments required for determining the performance of automotive flashers.
Standard
AUTOMOTIVE GRAY IRON CASTINGS
1993-03-01
HISTORICAL
J431_199303
This SAE Standard covers the hardness, tensile strength, and microstructural requirements for gray iron sand mold castings used in automotive and allied industries. The chemical requirements for alloy gray iron automotive camshafts are included in the document under castings for special application with controlled composition and microstructure. Appendix A provides general information on application of gray iron in automotive castings and chemical composition to meet hardness, microstructural, and other properties needed for particular service conditions. Casting tensile strength estimates are provided in Appendix A for design reference.
Standard
AUTOMOTIVE GRAY IRON CASTINGS
1979-08-01
HISTORICAL
J431_197908
This standard covers the hardness and microstructural requirements for gray iron sand mold castings used in automotive and allied industries. The chemical requirements for alloy gray iron automotive camshafts are included in the standard under casting for special application with controlled composition and microstructure. The Appendix provides general information on application of gray iron in automotive castings and chemical composition to meet hardness, microstructural, and other properties needed for particular service conditions. The mechanical properties in the Appendix are provided for design purposes. Note: This document was rewritten in June 1970. The materials described by the grade numbers are different than in the former writing.
Standard
AUTOMOTIVE GRAY IRON CASTINGS
1975-01-01
HISTORICAL
J431C_197501
This SAE Standard applied to gray iron castings cast in sand molds in the products of the automobile, truck, tractor, and allied industries, NOTE: This document was rewritten in January 1975. The materials described by the grade numbers are different than in the former writing.
Standard
AUTOMOTIVE MALLEABLE IRON CASTINGS
1975-01-01
HISTORICAL
J158A_197501
SAE J432 and J433 have been discontinued and replaced by this report. This SAE Standard covers castings of ferritic, pearlitic, tempered pearlite, and tempered martensitic grades of malleable iron used in products of the automotive and allied industries. Castings shall be heat treated to meet this SAE Standard
Standard
AUTOMOTIVE MALLEABLE IRON CASTINGS
1986-06-01
HISTORICAL
J158_198606
This SAE Standard covers the hardness and microstructural requirements for malleable iron castings-ferritic, pearlitic, tempered pearlitic, and tempered martensitic grades used in automotive and allied industries. Castings shall be heat treated to meet this SAE Standard. The Appendix provides general information on the application of malleable iron castings and their chemical composition to meet hardness, microstructure, and other properties needed for particular service conditions. The mechanical properties in the Appendix are provided for design purposes.
Standard
AUTOMOTIVE PIPE FITTINGS
1992-06-01
HISTORICAL
J530_199206
This SAE Standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figures 1 to 17 and Tables 1 to 6 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.
Standard
AUTOMOTIVE PIPE FITTINGS
1981-01-01
HISTORICAL
J530_198101
This standard includes complete general and dimensional specifications for those types of pipe fittings commonly used in the automotive and other mass production industries where the use of lubricants or sealers is objectionable. The automotive pipe fittings shown in Figs. 1-17 and Tables 2-7 are intended for general automotive and similar applications involving low or medium pressures or in conjunction with automotive tube fittings in piping systems.
Standard
AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS
1992-02-01
HISTORICAL
J531_199202
This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.
Standard
AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS
1993-06-01
HISTORICAL
J531_199306
This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.
Standard
AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS
1981-01-01
HISTORICAL
J531_198101
This standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figs. 1-6 and Tables 2-4) commonly used in automotive and related industrial applications.
Standard
AUTOMOTIVE PIPE, FILLER, AND DRAIN PLUGS
1994-06-01
HISTORICAL
J531_199406
This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and related industrial applications.
