Search Results

Worldwide diesel fuels differ in their composition and therefore in thermo-physical properties. Some of these properties are known to have little effect on the combustion process. Others, like the cetane number, have dramatic influence on the combustion formation and thus on the heat release rate and more important the formation of soot and NOx. In an experiment series various commercially available fuel types, like EN 590 [1], ASTM D975 [2] and JIS K 2204 [3], have been compared to alternative diesel fuels such as FAME, GtL and premium diesel fuel with increased cetane number. A specially designed research injector was used in order to provide full optical access to one single fuel jet injected and combusted in a constant volume vessel. First, the liquid fuel phase propagation has been investigated by means of Mie-scattering and the liquid penetration depth and the spray cone angle have been evaluated.

Flash boiling conditions, where the fuel is superheated with respect to cylinder pressure, are often found in gasoline direct injection engines. This phenomenon affects the flowrate of the fuel and can cause choking of the nozzle. In this work we present multi-dimensional simulations of flashing internal injector flow. The modeled fluid quality (mass fraction of vapor) tends towards the equilibrium quality based on the Homogenous Relaxation Model. The relaxation time is dependent on the local pressure, the vapor pressure, and the void fraction. Simulations of the internal flow are presented and, where possible, validated with experimental data. Both two- and three- dimensional computational results show geometrically-induced phase change, similar to cavitation, near the nozzle entrance. Near the nozzle exit plane the phase change occurs at all radial locations and can be quite sensitive to temperature.

Pre-chamber ignition systems enable the combustion of homogeneous lean mixtures in internal combustion engines with significantly increased thermal efficiency. Such ignition systems provide a much higher ignition energy compared to a common spark ignition by burning a small portion of the charge in a separate chamber, generating multiple ignition sites in the main combustion chamber and increasing the turbulent flame speed. Pre-chamber ignition systems are commonly used in large natural gas engines but the integration in automotive engines is not feasible so far due to the lack of suitable fuelling systems needed to keep the pre-chamber mixture stoichiometric at lean operation of the engine. Based on preliminary investigations we developed an ignition system with fuelled pre-chamber for automotive engines utilizing the available space for the conventional spark plug.

Homogeneous lean or diluted combustion can significantly increase the efficiency of spark ignition engines. Active fuelled pre-chamber ignition systems can overcome the problem that common spark ignitions systems are incapable to ignite strongly diluted mixtures. A small portion of the charge is burned in a separated chamber, which is connected to the main chamber by multiple small orifices. The combustion inside the pre-chamber generates hot gases, which penetrate into the main chamber and ignite the diluted charge on multiple sites. Active pre-chamber ignition systems feature a separate fuelling or scavenging system in addition to the one of the main combustion chambers. Preferably, gaseous fuel is used for the pre-chamber fuelling allowing better dosing accuracy and mixture preparation inside the pre-chamber.

This paper describes the principles, effects and the potentials of impulse charging systems applied to SI and Diesel engines. In general, impulse charging is realized by closing the inlet port upstream of the inlet valve during the intake stroke with an additional switching device. The piston, moving towards bottom dead center, generates a vacuum inside the combustion chamber and inlet port. By opening the switching device abruptly, the sub-atmospheric pressure level induces an enhanced volumetric efficiency due to the significantly increased gas dynamic effects in the intake manifold. One major advantage of impulse charging in comparison to the well known supercharging techniques lies in the dynamic behavior. The charging effect can be realized within one engine cycle. Furthermore, impulse charging provides high low-end torque, a nearly constant torque over a wide engine speed range with charging rates from 20% to 30%.

The spray formation of two different gasoline port fuel injectors has been studied in three stages of the mixture formation process using measured liquid fuel distributions. The injector characteristics were determined in fundamental chamber experiments providing the time dependent spray penetration and the internal structure of the spray in quiescent air by a laser light sheet technique. For the sane injectors the interaction between port flow and spray was investigated inside the port of a production engine. A strong dependence of the fuel distribution inside the port on the engine operation point was found for both injectors. This fuel distribution provides information on wall film generation and the optimum orientation of the injector inside the suction pipe.

Multi-hole DI injectors are being adopted in the advanced downsized DISI ICE powertrain in the automotive industry worldwide because of their robustness and cost-performance. Although their injector design and spray resembles those of DI diesel injectors, there are many basic but distinct differences due to different injection pressure and fuel properties, the sac design, lower L/D aspect ratios in the nozzle hole, closer spray-to-spray angle and hense interactions. This paper used Phase-Contrast X ray techniques to visualize the spray near a 3-hole DI gasoline research model injector exit and compared to the visible light visualization and the internal flow predictions using with multi-dimensional multi-phase CFD simulations. The results show that strong interactions of the vortex strings, cavitation, and turbulence in and near the nozzles make the multi-phase turbulent flow very complicated and dominate the near nozzle breakup mechanisms quite unlike those of diesel injections.

It is well know that the internal flow field and nozzle geometry affected the spray behavior, but without high-speed microscopic visualization, it is difficult to characterize the spray structure in details. Single-hole diesel injectors have been used in fundamental spray research, while most direct-injection engines use multi-hole nozzle to tailor to the combustion chamber geometry. Recent engine trends also use smaller orifice and higher injection pressure. This paper discussed the quasi-steady near-nozzle diesel spray structures of an axisymmetric single-hole nozzle and a symmetric two-hole nozzle configuration, with a nominal nozzle size of 130 μm, and an attempt to correlate the observed structure to the internal flow structure using computational fluid dynamic (CFD) simulation. The test conditions include variation of injection pressure from 30 to 100 MPa, using both diesel and biodiesel fuels, under atmospheric condition.

In DISI engines spray distribution and atomization directly influence mixture formation, the quality of combustion and the resulting emissions. Constant Volume Chambers (CVC) are commonly used to characterize sprays of gasoline injectors. The CVCs provide good optical access but the flow condition of the engine cannot be reproduced. Optically accessible engines in contrast deliver realistic flow conditions but have restricted optical access. In former investigations we compared the spray propagation of different injectors in constant volume chambers and in optical accessible engines. These results showed a clear difference of the spray propagation in the CVC and the engine, especially at high charge motion conditions in the engine. To find an appropriate way to investigate the impact of different charge motion a flow channel was built with adjustable crossflow velocities from 5-50 m/s. The spray propagation during the injection process was measured with high-speed shadowgraphy.

A full understanding and characterization of the near-field of diesel sprays is daunting because the dense spray region inhibits most diagnostics. While x-ray diagnostics permit quantification of fuel mass along a line of sight, most laboratories necessarily use simple lighting to characterize the spray spreading angle, using it as an input for CFD modeling, for example. Questions arise as to what is meant by the “boundary” of the spray since liquid fuel concentration is not easily quantified in optical imaging. In this study we seek to establish a relationship between spray boundary obtained via optical diffused backlighting and the fuel concentration derived from tomographic reconstruction of x-ray radiography. Measurements are repeated in different facilities at the same specified operating conditions on the “Spray A” fuel injector of the Engine Combustion Network, which has a nozzle diameter of 90 μm.

The fuel spray behavior in the near nozzle region of a gasoline injector is challenging to predict due to existing pressure gradients and turbulences of the internal flow and in-nozzle cavitation. Therefore, statistical parameters for spray characterization through experiments must be considered. The characterization of spray velocity fields in the near-nozzle region is of particular importance as the velocity information is crucial in understanding the hydrodynamic processes which take place further downstream during fuel atomization and mixture formation. This knowledge is needed in order to optimize injector nozzles for future requirements. In this study, the results of three experimental approaches for determination of spray velocity in the near-nozzle region are presented. Two different injector nozzle types were measured through high-speed shadowgraph imaging, Laser Doppler Anemometry (LDA) and X-ray imaging.

In this paper an estimation method on location of peak pressure (LPP) employing flame ionization measurement, with the spark plug as a sensor, was discussed to achieve combustion parameters estimation at quick start of HEV engines. Through the cycle-based ion signal analysis, the location of peak pressure can be extracted in individual cylinder for the optimization of engine quick start control of HEV engine. A series of quick start processes with different cranking speed and engine coolant temperature are tested for establishing the relationship between the ion signals and the combustion parameters. An Artificial Neural Network (ANN) algorithm is used in this study for estimating these two combustion parameters. The experiment results show that the location of peak pressure can be well established by this method.

In this paper, the spray and combustion characteristics of biodiesel and diesel were investigated. The spray pictures of single injection, by means of a diesel pump test-bed, were taken by a high-speed camera video system in an atmospheric condition, and the effects of the pump speed, nozzle orifice diameter and nozzle opening pressure on the fuel spray structure and characteristics were studied under atmosphere condition. The results showed that the general law of biodiesel spray characteristics was similar to that of diesel. However, the spray penetration of biodiesel was longer than that of diesel, and the spray angles of biodiesel were only half angle of diesel. The experiment of combustion characteristics was conducted in a vitiated coflow combustor with the same diesel pump test-bed. The images of combustion flame were recorded by the high-speed camera system. Then the ignition characteristics were evaluated from the digital pictures by computer.

Two-dimensional Mie and LIEF techniques were applied to investigate the spray propagation, mixture formation and charge distribution at ignition time inside the combustion chamber of a direct injection SI engine. The results obtained provide the propagation of liquid fuel relative to the piston motion and visualize the charge distribution (liquid fuel and fuel vapor) throughout the engine process. Special emphasis was laid on the charge distribution at ignition time for stratified charge operation. By means of a LIEF technique it was possible to measure cyclic fluctuations in the fuel vapor distributions which explain the occurrence of misfiring.

To address stricter emission limits, GDI develops to increased fuel pressure. Current gasoline injectors are already operating at a pressure of up to 35 MPa and an elevation is still promising lower particle emissions and increased efficiency. There have been only few studies of GDI sprays at pressures >50 MPa published. Contrary, in diesel engines injection pressure up to 250 MPa are common. GDI and diesel injector designs limit liquid penetration in different ways to avoid wall wetting, which has a negative impact on emissions in GDI combustion concepts. With elevated fuel pressure the question arises which design concept limits the penetration depth more effectively. To investigate the properties of high pressure sprays, a GDI injector (100 MPa max. fuel pressure) and an injector with diesel-like design are compared. High speed Shadowgraphy and Schlieren technique are used to gather information of liquid and vapor phase propagation.

Nitric oxides are the key pollutants emitted from SI engines today. In the work presented, the effect of different fuel-components on the NOx-emission of a four stroke SI engine and cross connections between different fuel properties were investigated in front of and behind the catalyst and compared to investigations described in literature. For the investigation presented a variety of different fuels has been produced. The content of aromatics, olefins, oxygen and the mid-range volatility has been changed systematically while only fuels with a good driveability were included in the investigation. The NOx-emission of 17 fuels tested was measured in front of and behind the catalyst. The tests were carried out with a single cylinder test engine using a constant air/fuel ratio.

Given the importance of the fuel-injection process on the combustion and emissions performance of gasoline direct injected engines, there has been significant recent interest in understanding the fluid dynamics within the injector, particularly around the needle and through the nozzles. The pressure losses and transients that occur in the flow passages above the needle are also of interest. Simulations of these injectors typically use the nominal design geometry, which does not always match the production geometry. Computed tomography (CT) using x-ray and neutron sources can be used to obtain the real geometry from production injectors, but there are trade-offs in using these techniques. X-ray CT provides high resolution, but cannot penetrate through the thicker parts of the injector. Neutron CT has excellent penetrating power but lower resolution.

Flexible and multiple injections are an important strategy to fulfill today's exhaust emission regulations. To optimize injection processes with an increasing number of adjustable parameters knowledge about the basic mechanisms of spray breakup, propagation, evaporation and ignition is mandatory. In the present investigation the focus is set on spray formation and ignition. In order to simulate current diesel-engine conditions measurements were carried out in a high-temperature (1000 K) and high-pressure (10 MPa) vessel with optical accesses. A piezo servo-hydraulic injector pressurized up to 200 MPa was used to compare four single injection durations and four multi-injection patterns in the ignition phase. All measurements were performed with CEC RF-03-06, a legislative reference fuel. For the spray measurements, a program of 16 to 18 different operating points was chosen to simulate engine conditions from cold start to full load.

Understanding the causal loop from injection to combustion in modern direct injection engines is essential to improve combustion and reduce emissions. In this work, the section from injection to fuel-evaporation in this causal loop was investigated using different optical measurement techniques, with a focus on drop size measurements using Phase Doppler Anemometry (PDA). One spray jet of a modern DISI multi-hole injector was investigated using gasoline RON 95 fuel and two single component alkane fuels (n-hexane / n-decane). In a first step the macroscopic spray formation and propagation of this spray jet were studied using a 2D-Mie-scattering technique in an optical injection chamber at homogenous charge DISI conditions. Furthermore, the droplet size distribution and mean diameter were determined spatially and temporally resolved for an ambient pressure of 0.3MPa and different ambient temperature (323K / 423K / 523K) conditions in the optical chamber using Phase Doppler Anemometry.

In spark-ignition engines, high exhaust gas recirculation (EGR) rates have demonstrated their potential in reducing fuel consumption and emissions. However, irregular combustion at high residual gas concentrations limits the EGR rates. The following study presents a strategy that has been developed to investigate the influence of complex charge motion on mixture formation and combustion for high residual gas concentrations with the aim of extending these limits. An optically accessible single-cylinder SI Engine with direct injection was used to measure the charge distribution by means of laser induced fluorescence (LIF). A special device inside the inlet pipe gave the possibility to generate a defined swirl motion overlaying a tumble motion given by the design of the inlet ports.