Search Results

A quasidimensional engine simulation which uses the concepts of fractal geometry to model the effects of turbulence on flame propagation in a homogeneous charge SI engine has been developed. Heat transfer and blowby/crevice flow submodels are included in this code and the submodels chosen are found to be reasonable. The model predictions of cylinder pressure histories are then compared with experimental data over a range of loads, equivalence ratios, and engine speeds. The model is not adjusted in any manner to yield better agreement with the data, other than by tuning the simple turbulence model used so as to yield agreement with data for the nonreacting flow. However, current information about the flame wrinkling scales in an engine is inadequate. Therefore, predictions are made for three different assumptions about the flame wrinkling scales which span the range of physically possible scales.

A quasi-dimensional model for a direct injection diesel engine was developed based on experiments at Sandia National Laboratory. The Sandia researchers obtained images describing diesel spray evolution, spray mixing, premixed combustion, mixing controlled combustion, soot formation, and NOx formation. Dec [1] combined all of the available images to develop a conceptual diesel combustion model to describe diesel combustion from the start of injection up to the quasi-steady form of the jet. The end of injection behavior was left undescribed in this conceptual model because no clear image was available due to the chaotic behavior of diesel combustion. A conceptual end-of-injection diesel combustion behavior model was developed to capture diesel combustion throughout its life span. The compression, expansion, and gas exchange stages are modeled via zero-dimensional single zone calculations.

Variable compression engines are a mean to meet the demand on lower fuel consumptions. A high compression ratio results in high engine efficiency, but also increases the knock tendency. On conventional engines with fixed compression ratio, knock is avoided by retarding the ignition angle. The variable compression engine offers an extra dimension in knock control, since both ignition angle and compression ratio can be adjusted. A vital question is thus what combination of compression ratio and ignition angle should be used to achieve maximum engine efficiency. Fuel optimal control of a variable compression engine is studied and it is shown that a crucial component is the model for the engine torque. A model for the produced work that captures the important effects of ignition and compression ratio is proposed and investigated. The main task for the model is to be a mean for determining the fuel optimal control signals, for each requested engine torque and speed.

We present a multidimensional numerical model that calculates turbulent premixed flame propagation, assuming the flames have fractal geometries. Two scaling transformations, previously developed for laminar flames, are used to incorporate the fractal burning model in KIVA-II1, a numerical hydrodynamics code for chemically reactive flows. In this work the model is implemented for propane/air mixtures. For applications to internal combustion engines, we have also developed a fractal model for early flame kernel growth. Our multidimensional model can be used in experimental comparisons to test postulated fractal parameters, and we begin this task by comparing calculated results with measurements of propane/air combustion in a spark ignition engine. Good agreement is obtained between computed and measured flame positions and pressures in all cases except a low engine speed case.

It is a very challenging problem to reliably ignite extremely lean mixtures, especially for the low speed, high load conditions of large-bore natural gas engines. If these engines are to be use for the distributed power generation market, it will require operation with higher boost pressures and even leaner mixtures. Both place greater demands on the ignition system. The railplug is a very promising ignition system for lean burn natural gas engines with its high-energy deposition and high velocity plasma arc. It requires care to properly design railplugs for this new application, however. For these engines, in-cylinder pressure and mixture temperature are very high at the time of ignition due to the high boost pressure. Hot spots may exist on the electrodes of the ignitor, causing pre-ignition problems. A heat transfer model is proposed in this paper to aid the railplug design. The electrode temperature was measured in an operating natural gas engine.

The objective is to investigate models of the specific heat ratio for the single-zone heat release model, and find a model accurate enough to introduce a modeling error less than or in the order of the cylinder pressure measurement noise, while keeping the computational complexity at a minimum. Based on assumptions of frozen mixture for the unburned mixture and chemical equilibrium for the burned mixture, the specific heat ratio is calculated using a full equilibrium program for an unburned and a burned air-fuel mixture, and compared to already existing and newly proposed approximative models of γ. A two-zone mean temperature model, Matekunas pressure ratio management and the Vibe function are used to parameterize the mass fraction burned. The mass fraction burned is used to interpolate the specific heats for the unburned and burned mixture, and then form the specific heat ratio, which renders a small enough modeling error in γ.

With stricter emission legislations and customer demands on low fuel consumption, good control strategies are necessary. This may involve control of variables that are hard, or even impossible, to measure with real physical sensors. By applying estimators or observers, these variables can be made available. The quality of a real sensor is determined by e.g. accuracy, drift and aging, but assessing the quality of an estimator is a more subtle task. An estimator is the result of a design work and hence, connected to factors like application, model, control error and robustness. The air mass-flow in a diesel engine is a very important quantity that has a direct impact on many control and diagnosis functions. The quality of the air mass-flow sensor in a diesel engine is analyzed with respect to day-to-day variations, aging, and differences in engine configurations. The investigation highlights the necessity of continuous monitoring and adaption of the air mass-flow.

Observers for air mass flow to the cylinder is studied on a turbocharged SI-engine with wastegate. A position change of the wastegate influences the residual gas mass and causes the volumetric efficiency to change, which produces a transient in the air mass flow to the cylinder. Two standard methods of estimating air-to-cylinder are investigated. A new nonlinear air-to-cylinder observer is suggested with two states: one for intake manifold pressure and one for the offset in in-cylinder air mass compared to expected through the volumetric efficiency. The observers are validated on intake manifold pressure data from a turbocharged spark ignited production engine with wastegate.

An analytic model for cylinder pressures in spark ignited engines is developed and validated. The main result is a model expressed in closed form that describe the in-cylinder pressure development of an SI engine. The method is based on a parameterization of the ideal Otto cycle and takes variations in spark advance and air-to-fuel ratio into account. The model consists of a set of tuning parameters that all have a physical meaning. Experimental validation on two engines show that it is possible to describe the in-cylinder pressure of a spark ignited combustion engine operating close to stoichiometric conditions, as a function of crank angle, manifold pressure, manifold temperature and spark timing.

An On-Board Distillation System (OBDS) was developed to extract, from gasoline, a highly volatile crank fuel that allows the reduction of startup fuel enrichment and significant spark retard during cold starts and warm-up. This OBDS was installed on a 2001 Lincoln Navigator to explore the emissions reductions possible on a large vehicle with a large-displacement engine. The fuel and spark calibration of the PCM were modified to exploit the benefits of the OBDS startup fuel. Three series of tests were performed: (1) measurement of the OBDS fuel composition and distillation curve per ASTM D86, (2) measurement of real-time cold start (20 °C) tailpipe hydrocarbon emissions for the first 20 seconds of engine operation, and (3) FTP drive cycles at 20 °C with engine-out and tailpipe emissions of gas-phase species measured each second. Baseline tests were performed using stock PCM calibrations and certification gasoline.

Throttles and wastegates are devices used in modern engines for accurate control of the gas flows. It is beneficial, for the control implementation, to have compact and accurate models that describe the flow behavior. The compressible isentropic restriction is a frequently used model, it is simple and reasonable accurate but it has some issues. One special issue is that it predicts that the choking occurs at too high pressure ratios, for example the isentropic model predicts choking at a pressure ratio of 0.52, while experimental data can have choking at 0.4 or even lower. In this work, experimental data is acquired from throttles tested both in a flow bench and mounted as main throttle on a turbocharged gasoline engine. To analyze the flow behavior several flow characterizations are performed at different throttle openings.

As natural gas engines are designed to operate leaner and with increased boost pressure, durability of the spark plugs becomes problematic. Among the various new ignition devices that have been considered to solve some of the problems facing spark plugs, railplugs appear to hold clear advantages in some areas. There are two types of railplugs: coaxial rail and parallel rail. This paper reports the results of an experimental study of various parameters that affect the performance of parallel railplugs. Their performance was quantified by the distance that the arc traveled along the rails from the initiation point. Travel along the rails is thought to be an important performance metric because rail-travel limits excessive local wear and produces a distributed ignition source which can potentially reduce mixture inhomogeneity induced ignition problems.

A program package, that calculates chemical equilibrium and thermodynamic properties of reactants and products of a combustion reaction between fuel and air, has been developed and validated. The package consists of the following four parts: 1) A program for calculating chemical equilibrium. 2) A database that contains thermochemical information about the molecules, which comes from the GRI-Mech tables. 3) A GUI that allows the user to easily select fuels, fuel/air ratio for the reaction, and combustion products. 4) A set of functions designed to access the thermochemical database and the chemical equilibrium programs. Results are validated against both the NASA equilibrium program (Gordon and McBride, 1994) and the program developed by Olikara and Borman (1975). It is shown that the new method gives results identical to those well recognized Fortran programs.

The work extends a methodology, for searching for optimal heat release profiles, by adding complex constraints on states. To find the optimum heat release profile a methodology, that uses available theory and methods, was developed that enables the use of state of the art optimal control software to find the optimum combustion trace for a model. The methodology is here extended to include constraints and the method is then applied to study how sensitive the solution is to different effects such as heat transfer, crevice flow, maximum rate of pressure rise, maximum pressure, knock and NO generation. The Gatowski single zone model is extended to a pseudo two zone model, to get an unburned zone that is used to describe the knocking and a burned zone for NO generation. A modification of the extended Zeldovich mechanism that makes it continuously differentiable, is used for NO generation.

In premixed turbulent combustion models, two mechanisms have been used to explain the increase in the flame speed due to the turbulence. The newer explanation considers the full range of turbulence scales which wrinkle the flame front so as to increase the flame front area and, thus, the flame propagation speed. The fractal combustion model is an example of this concept. The older mechanism assumes that turbulence enables the penetration of unburned mixtures across the flame front via entrainment into the burned mixture zone. The entrainment combustion or eddy burning model is an example of this mechanism. The results of experimental studies of combustion regimes and the flame structures in SI engines has confirmed that most combustion takes place at the wrinkled flame front with additional combustion taking place in the form of flame fingers or peninsulas.

EmiSense Technologies, LLC (www.emisense.com) is commercializing its electronic particulate matter (PM) sensor that is based on technology developed at the University of Texas at Austin (UT). To demonstrate the capability of this sensor for real-time PM measurements and on board diagnostics (OBD) for failure detection of diesel particle filters (DPF), independent measurements were performed to characterize the engine PM emissions and to compare with the PM sensor response. Computational fluid dynamics (CFD) modeling was performed to characterize the hydrodynamics of the sensor's housing and to develop an improved PM sensor housing with reproducible hydrodynamics and an internal baffle to minimize orientation effects. PM sensors with the improved housing were evaluated in the truck exhaust of a heavy duty (HD) diesel engine tested on-road and on a chassis dynamometer at the University of California, Riverside (UCR) using their Mobile Emissions Laboratory (MEL).

Three methods for estimating the compression from measured cylinder pressure traces are described and evaluated for both motored and fired cycles against simulated and measured cylinder pressure. The first two rely upon a model of polytropic compression, and it is shown that they give a good estimate of the compression ratio for simulated cycles for low compression ratios. For high compression ratios, these simple models lack the information about heat transfer. The third method includes a standard heat transfer and crevice effect model, together with a heat release model and is able to estimate the compression ratio more accurately.

Modelbased systems engineering is becoming an important tool when meeting the challenges of developing the complex future vehicles that fulfill the customers and legislators ever increasing demands for reduced pollutants and fuel consumption. To be able to work systematically and efficiently it is desirable to have a library of components that can be adjusted and adapted to each new situation. Turbocharged engines are complex and the compressor model serves as an in-depth example of how a library can be designed, incorporating the basic physics and allowing fine tuning as more information becomes available. A major part of the paper is the summary and compilation of a set of rules of thumb for compressor map extrapolation. The considerations discussed are extrapolation to surge, extrapolation to restriction region, and extrapolation out to choking.

The combustion process has a high impact on the engine efficiency, and in the search for efficient engines it is of interest to study the combustion. Optimization and optimal control theory is used to compute the most efficient combustion profiles for single zone model with heat transfer and crevice effects. A model is first developed and tuned to experimental data, the model is a modification of the well known Gatowski et al.-model [1]. This model is selected since it gives a very good description of the in-cylinder pressure, and thus the produced work, and achieves this with a low computational complexity. This enables an efficient search method that can maximize the work to be developed. First, smooth combustion profiles are studied where the combustion is modeled using the Vibe function, and parametric optimization is used to search for the optimal profile.

Condensation of fuel vapor on the cold surfaces within the combustion chamber is investigated as a possible mechanism for increased HC emissions from SI engines during cold start. A one-dimensional, transient, mass diffusion analysis is used to examine the condensation of single-species fuels on the surfaces of the combustion chamber as the pressure within the cylinder rises during compression and combustion, and re-vaporization during expansion, blowdown, and exhaust. The effects of wall temperature, fuel volatility, and engine load and speed on this mechanism are also discussed. This analysis shows that low-volatility fuel components can condense on the surfaces of the combustion chamber when the surface temperatures are sufficiently low. This condensed fuel may re-vaporize during the power and exhaust strokes, or it may remain in the combustion chamber until surface temperatures rise, perhaps tens of seconds later.