Search Results

Electronic Stability Control (ESC) is an important measure to proactively guarantee vehicle safety. In this paper, the method of four-wheel hub-motor torque control is compared with the traditional single-wheel hydraulic brake control in ESC system. The control strategy adopts the hierarchical structure. In upper controller, the stability of the vehicle is identified by threshold method, the additional yaw moment control uses a way to get the moment including feedforward and feedback parts based on the linear quadratic regulator (LQR). The medium controller is tire slip rate control, in order to get the optimal target slip rate from the upper additional yaw moment, a method of quadratic programming to optimize the longitudinal force is proposed for each wheel. The inputs of tire state for the magic tire model is introduced so as to calculate the target slip rate from the target longitudinal force.

This work analyzes the transmission efficiency of vehicle driveline including the gearbox, universal transmission and differential. Based on the structure of transmission, mathematic models are built to analyze transmission's characteristics. However, an experiment reveals the limitation of this method. Then, the paper statistically analyzes the experimental data and mainly analyzes the influencing factors. Then Neural Network is used to build the efficiency model. A method called “filling data and gradually extrapolating” is used when building neural network model. Finally, the neural network model is used in the simulation of fuel consumption. The conclusion is Neural Network model can imitate the transmission efficiency of vehicle driveline efficiently, but its internal structure is not clear so other modeling methods are needed to be found.

The retarder is an important auxiliary braking device of heavy vehicles. However, the stirring air in the working wheels of the idle retarder would cause the transmission loss when the vehicle is traveling in non-braking state [1]. For certain driving conditions, the air-friction characteristics in the working wheels of the idle retarder are analyzed first. Then the relationship between the air density and the torque produced by stirring air is studied. The thermal characteristics of the retarder in the idle condition are also concerned according to the energy flow and heat transfer. Meanwhile, the increased transmission loss caused by the rising temperature of the stirring air and its inference on the transmission stability are also studied. Finally, the optimal range of air vacuum degrees in the working wheel of the idle retarder is determined and the evaluations for the air-friction and the heat transfer characteristics are given for the vacuum degrees.

The hydraulic retarder is the most stabilized auxiliary braking system [1-2] of heavy-duty vehicles. When the hydraulic retarder is working during auxiliary braking, all of the braking energy is transferred into the thermal energy of the transmission medium of the working wheel. Theoretically, the residual heat-sinking capability of the engine could be used to cool down the transmission medium of the hydraulic retarder, in order to ensure the proper functioning of the hydraulic retarder. Never the less, the hydraulic retarder is always placed at the tailing head of the gearbox, far from the engine, long cooling circuits, which increases the risky leakage risk of the transmission medium. What's more, the development trend of heavy load and high speed vehicle directs the significant increase in the thermal load of the hydraulic retarder, which even higher than the engine power.

Hydraulic retarder has been widely applied on military vehicles and heavy commercial vehicles because of it could provide great brake torque and has lasting working time [1]. In order to reduce driver's frequent actions in braking process and prevent hydraulic retarder system from overheating, it is need to apply constant braking torque control, this control target has a strict requirement to hydraulic control system design. Many parameters often require repeated test to determine, which increases the R&D cost and extends the research cycle. This paper tries to find a time-efficient research method of hydraulic retarder control system through studying on a heavy military vehicle hydraulic retarder system. Hydraulic retarder model is set up through test data. The hydraulic control system is built based on AMESim. Controller model is set up based on PID control. The whole vehicle brake model is built based on MATLAB/Simulink.

Path planning system, which is one of driver assistance systems, can calculate the driving paths and estimate the driving time through the road information provided by information source. Traditional path planning systems calculate the driving paths through Dijsktra's algorithm or A* algorithm but only consider the road information from electronic maps. It is not safe enough for operating vehicles because of the insufficient information of vehicle performance as well as the driver's willingness. This study is based on the Dijsktra's algorithm, which comprehensively considered vehicular active safety constraints such as road information, vehicle performance and the driver's willingness to optimize the Dijsktra's algorithm. Then the path planning system can calculate the optimal driving paths that would satisfy the safety requirement of the vehicle. This study used LabVIEW as a visual host computer and MATLAB to calculate dynamic property of the vehicle.

The closed cabin temperature is anticipated to be cooled down when it is a bit hot inside the driving car. The traditional air-condition lowers the cabin temperature by frequently switching the status of the compressor, which increases the engine’s parasitic power and shortens the compressor’s service-life. The semiconductor auxiliary cooling system with the properties of no moving parts, high control precision and quick response has the potential to assist the on-board air-condition in modulating the cabin temperature with relative small ranges. Little temperature differences between the cabin and the outside environment means that the system energy consumption to ensure the occupant comfort is relatively low and the inefficiency could be made up by the renewable energy source.

Vehicle hydraulic retarders are applied in heavy-duty trucks and buses as an auxiliary braking device. In traditional cooling systems of hydraulic retarders, the working fluid is introduced into the heat exchanger to transfer heat to the cooling liquid in circulation, whose heat is then dissipated by the engine cooling system. This prevents the waste heat of the working fluid from being used effectively. In hydraulic retarder cooling system based on the Organic Rankine Cycle, the organic working fluid first transfers heat with the hydraulic retarder working fluid in Rankine cycle, and then outputs power through expansion machine. It can both reduce heat load of the engine cooling system, and enhance thermal stability of the hydraulic retarder while recovering and utilizing braking energy. First of all, according to the target vehicle model, hydraulic retarder cooling system model based on Rankine cycle is established.

In order to improve the driving experience of drivers and the efficiency of vehicle development, a method of objective drivability for passenger car powertrain is proposed, which is based on prior knowledge, principal component analysis (PCA) and SMART principle. First, drivability parameters of powertrain for passenger cars are determined according to working principle of powertrain, including engine torque, engine speed, gearbox position, accelerate pedal, brake pedal, steering wheel angle, longitudinal acceleration and lateral acceleration, etc. The drivability quantitative index system is designed based on field test data, prior knowledge and SMART principles. Then, D-S evidence theory and sliding window method are applied to identify objective drivability evaluation conditions of powertrain for passenger cars, including static gearshift conditions, starting conditions, creep conditions, tip-in, tip out, upshift conditions, acceleration, downshift conditions and de-acceleration.

In order to solve the problems of insufficient accuracy for theoretical models and data-driven models for objective drivability evaluation requiring a large amount of data, an objective drivability evaluation method based on a hierarchical mixture model is proposed. First, a novel method of constructing a drivability evaluation system is developed, which combined by work breakdown structure (WBS) and analytic hierarchy process (AHP). Then, downshift condition is taken as a case study, and the subdivision condition is identified based on the hybrid mixture model. What's more, the drivability evaluation indexes of downshift condition are analyzed to establish the evaluation system of drivability.

In the Rankine cycle, the pressure differential generated by the phase change of the working fluid produces turbine output power, which enables the recovery of waste heat from the internal combustion engine. The heat transfer ability of the evaporator is the key factor that determines the quality of turbine's mechanical work. In this paper, the performance of the evaporator with two-phase zone and preheated zone is studied. After obtaining the thermal characteristics of diesel engine exhaust from the experimental data, the mathematical model of the evaporator is built according to the specific working conditions of ORC and geometrical parameters of the evaporator. Three typical engine operating conditions are used to estimate the heat transfer characteristics of the evaporator. The result shows that, in the evaporator, the heat transfer coefficient of the Rankine working fluid is much greater than the exhaust side of the engine.

In order to improve the drivability of passenger cars with dual clutch transmission (DCT) and reveal the criteria for objective evaluation criteria and characteristic index and feature index division of vehicles under specific working conditions, a drivability evaluation system that integrates data-driven and the consistency between subjective and objective is proposed. At first, combined with the control principle and dynamics theory of specific working conditions, a quantitative index system of vehicle drivability is constructed, including three modules: data source, evaluation working conditions and objective indicators. Then, a novel intelligent drivability objective evaluation tools (I-DOET) is designed, including data acquisition, de-noising, working condition recognition, feature extraction and automatic scoring.

In this paper a new pressure control method of a modified accumulator-type Electro-hydraulic Braking System (EHB) is proposed. The system is composed of a hydraulic motor pump, an accumulator, an integrated master cylinder, a pedal feel simulator, valves and pipelines. Two pressurizing modes are switched between by-motor and by-accumulator to adapt different pressure boost demands. A differentiator filtering raw sensor signal and calculating pedal speed is designed. By using the pedal feel simulator, the relationship between wheel pressures and brake force is decoupled. The relationships among pedal displacement, pedal force and wheel pressure are calibrated by experiments. A model-based PI controller with predictor is designed to lower the influences caused by delay. Moreover, a self-tuning regulator is introduced to deal with the parameter’s time-varying caused by temperature, brake pads wearing and delay variation.

On road simulation, both the traditional iterative method based on frequency response function (FRF) and adaptive control method based on the CARMA model are realized by using linear model to identify the target test system. However the real test system is very complicated because of various nonlinear factors. Linear models approximately describe the system only in a small range. Therefore, system simulation methods can not be used to validate the developed control algorithm and the uncertainty of test accordingly increases. As mentioned above, this paper presents a model to identify the nonlinear test system using NARMA dynamic neural network and discusses how to make the model parameters in detail. Using the test input-output series data, this network was trained by Levenberg-Marquardt method. Results of verification simulation show the validation of the nonlinear model.

Focusing the vehicle riding safety and global environmental problems, plenty of solutions on vehicle braking systems appeals during the recent period. Criteria and standards set up for commercial vehicles which should have equipped assisted braking systems were established by amounts of governments. Since eddy current retarders plays an important role in the area of assisted braking system, this article presents an energy-recuperation retarder, which is parallel connected with the driveline through a planet gear system. This paper offers a particular Energy-Recuperation Eddy Current Retarder (ERECR) system with a pedal control system and its characteristics is presented, either. Initially, the constitution of the energy-recuperation eddy current retarder system is established whereas the working principle of the energy-recuperation eddy current retarder is presented by modeling the system and simulation.

Analogous to a vacuum boosted system, Electro-Hydraulic Braking System (EHB) is free from engine vacuum and supplies a braking force proportional to driver input. The independence of engine vacuum makes it especially suitable to be used in electric vehicles (EVs) and hybrid electric vehicles (HEVs). As a key component of EHB, master cylinder is driven by the pump rather than the vacuum booster. Even if the pump fails, the cylinder can also build proper pressure. Meanwhile, in order to maintain the pedal feeling, a pedal stroke simulator is applied in the system. In this paper, aiming at decreasing the size and cost of master cylinder and providing an ideal pedal feeling without compromise of performance, a new integrated master cylinder of EHB system is designed including two parts: master cylinder and pedal stroke simulator. The key components of the integrated master cylinder are motor pump, solenoid valves and composite springs.

The head-up display system can overlay the real object with the projected image to assist the driver in driving. However, when road conditions are bad, the continuous vibration of the vehicle will cause the vehicle to tilt and shift. At this time, the projected image and the real object do not overlap well. This paper presents a correction algorithm for a head-up display system. The algorithm corrects the position of the projected image by inputting the tilt state of the vehicle. In this paper, the coordinate axis with the driver's eye as the origin is first established. Then the tilt state of the vehicle is decomposed into the rotation angle in three directions and the displacement in the vertical direction. Finally, the position of the projected image is corrected by inputting the tilt state of the vehicle so that the projected image can remain on the real object at all times. The simulation model is established in Unity3D.

Road simulation experiment in laboratory is a most important method to enhance the design quality of vehicle products. Presently, two main control techniques for road simulation—remote parameter control (RPC) and minimum variance adaptive control—are both defective: the former becomes an open-loop control after generating the drive signals, however the latter is essentially a kind of gradual control. To realize the closed-loop control and increase the control quality, this article brings forward a PID open-closed loop control method. Firstly taking the original road simulator as a group to identify, a nonlinear autoregressive moving average (NARMA) model was built with the dynamic neural network. Subsequently, this plant model was used to build the open-closed loop control system mentioned above. In the closed-loop a discrete PID controller was introduced to stabilize the system, while a P-type iterative learning control (ILC) was adopted to increase the control quality.

Lithium-ion batteries (LiBs) have been widely used in electrified vehicles, and the battery thermal management (BTM) system is needed to maintain the temperature that is critical to battery performance, safety, and health. Conventionally, three-dimensional battery thermal models are developed at the early stage to guide the design of the BTM system, in which battery thermophysical parameters (radial thermal conductivity, axial thermal conductivity, and specific heat capacity) are required. However, in most literature, those parameters were estimated with greatly different values (up to one order of magnitude). In this paper, an investigation is carried out to evaluate the magnitude of the influence of those parameters on the battery simulation results. The study will determine if accurate measurements of battery thermophysical parameters are necessary.

Nowadays, off-highway vehicles enjoyed a significant status in the national defense and civil construction. There is no doubt that the working conditions of off-highways are quite different from the conventional passenger cars, hence, their suspensions are particularly designed. Since the hydro-pneumatic suspension technology is maturely applied in engineering machinery, this paper presents a concept for a novel energy-harvesting device, which is applied in off-highway vehicles based on hydro-pneumatic suspension, namely, electro-hydraulic energy-harvesting suspension (EHEHS). The EHEHS took the fundamental of mechanism-electronic-hydraulic system, which consisted the following elements: a cylinder, 2 check valves, a hydro-pneumatic spring, a hydraulic motor, a DC motor, a processing circuit and a battery. In the EHEHS system, the cylinder is used to transmit the vibration energy into hydraulic energy, which is stored in hydro-pneumatic spring.