Search Results

The effects of variable intake-valve-timing on the gas exchange process and performance of a 4-valve direct-injection HCCI engine were computationally investigated using a 1D gas dynamics engine cycle simulation code. A non-typical strategy to actuate the pair of intake valves was examined; whereby each valve was assumed to be actuated independently at different timing. Using such an intake valves strategy, the obtained results showed a considerable improvement of the engine parameters such as load and charging efficiency as compared with the typical identical intake valve pair timings case. Additional benefits of minimizing pumping losses and improving the fuel economy were demonstrated with the use of the non-simultaneous actuation of the intake valve pair having the opening timing of the early intake valve coupled with a symmetric degree of crank angle for the timing of exhaust valve closing.

This paper presents a computational study of the airflow features within a motored 4-valve direct injection engine cylinder. An unconventional intake valve strategy was investigated; whereby each valve on the pair of intake valves was assumed to be actuated with different lifts and duration. One of the intake valves was assumed to follow a high-lift long duration valve-lift profile while the other was assumed to follow a low-lift short duration valve-lift profile. The pair of exhaust valves was assumed to be actuated with two identical low-lift short duration valve-lift profiles in order to generate the so-called negative valve overlapping (NVO). The in-cylinder flow fields developed with such intake valve strategy were compared to those produced in the same engine cylinder but with the application of identical low-lift short duration intake valve events.

Using EGR instead of throttle to control the load of a stoichiometric dual-fuel dieseline (diesel and gasoline) compression ignition (SDCI) engine with three-way catalyst (TWC) aftertreatment is considered a promising technology to address the challenges of fuel consumption and emissions in future internal combustion engines. High-speed imaging is used to record the flame signal in a single-cylinder optical engine with a PFI+DI dual injection system. The premixed blue flame is identified and separated using green and blue channels in RGB images. The effects of injection timing on SDCI combustion are studied. An earlier injection strategy is found to be ideal for soot reduction; however, the ignition-injection decoupling problem results in difficulties in combustion control. It is also found that a split injection strategy has advantages in soot reduction and thermal efficiency.

There is an increasing recognition of injector deposit (ID) formation in fuel injection equipment as direct injection spark ignition (DISI) engine technologies advance to meet increasingly stringent emission legislation and fuel economy requirements. While it is known that the phenomena of ID in DISI engines can be influenced by changes in fuel composition, including increasing usage of aliphatic alcohols and additive chemistries to enhance fuel performance, there is however still a great deal of uncertainty regarding the physical and chemical structure of these deposits, and the mechanisms of deposit formation. In this study, a mechanical cracking sample preparation technique was developed to assess the deposits across DISI injectors fuelled with gasoline and blends of 85% ethanol (E85).

The objective of the current research was to predict and analyze the flow through the grill of air intake system which is positioned behind the front wheel arch of vehicle. Most of the vehicle used today locates the grill of air intake at the front side so to acquire benefit of ram effect. In some cases, however, the grill is located behind the vehicle to improve wading performance. The geometry of air intake system of Land Rover Freelander was used in the modelling approach. The study was focused on different flow speeds on the grill at high load operation where the air speed at the grill side is high and creates negative pressure. The CFD results are validated against experimental data of steady flow test bench.

In this paper blends of diesel and gasoline (dieseline) fuelled Partially Premixed Compression Ignition (PPCI) combustion and the comparison to conventional diesel combustion is investigated. The tests are carried out using a light duty four cylinder Euro IV diesel engine. The engine condition is maintained at 1800 rpm, 52 Nm (equivalent IMEP around 4.3 bar). Different injection timings and different amounts of EGR are used to achieve the PPCI combustion. The results show that compared to the conventional diesel combustion, the smoke and NOx emissions can be reduced by more than 95% simultaneously with dieseline fuelled PPCI combustion. The particle number total concentration can be reduced by 90% as well as the mean diameter (from 54 nm for conventional diesel to 16 nm for G50 fuelled PPCI). The penalty is a slightly increased noise level and lower indicated efficiency, which is decreased from 40% to 38.5%.

There is a worldwide interest in the research of various alternative fuels for automotive engines for the purpose of reduction of CO2 and toxically harmful exhaust emissions. Coal-bed gas, the main component of which is methane, has been considered an attractive alternative fuel for combustion engines due to its abundant resources, high hydrogen-carbon ratios and very low soot formation tendency. The composition of available coal-bed gas, however, can vary considerably, and this has made its combustion stability difficult to control in conventional spark ignition engines. To overcome the problem, a combustion system with a swirl chamber connected to the main combustion chamber through an orifice has been developed for the use of coal-bed gas in spark ignition engines, and the corresponding combustion process has been studied using a developed combustion model involving flame kernel formation and flame front propagation.

Variations in air-fuel ratio within a 16-valve port-injection spark-ignition engine have been examined as a consequence of rapid transients in load at constant speed with fuel injection controlled by the production engine-management system and by a custom-built controller. The purpose was to minimize excursions from stoichiometry by the use of a controller to impose an injection strategy, guided by results obtained with the production management system. The strategy involves a model that takes account of manifold filling and the delays in transport of fuel from the injectors to the cylinder. The results show that the excursions in air-fuel ratio from stoichiometry were reduced from more than 25% to 6%.

This paper presents a computational investigation of the in-cylinder charge characteristics within a motored 4-valve direct injection HCCI engine cylinder with applied negative valve overlapping. Non-typical intake valve strategy was investigated; whereby the pair of intake valves was assumed to follow the same low-lift short-duration valve-lift profile but actuated at different timings. The phase of intake-valve-opening relative to that of exhaust-valve-closing was optimized in terms of pumping losses. The flow fields generated with such an intake valve strategy were compared to those produced in the same engine cylinder but with typical early and late intake-valve-timing. The computational results of such an approach showed modifications in the in-cylinder swirl and tumble motions during the intake and compression strokes.

With boosted HCCI operation on gasoline using residual gas trapping, the amount of residuals was found to be of importance in determining the boundaries of stable combustion at various boost pressures. This paper represents a development of this approach by concentrating on the effects of inlet valve events on the parameters of boosted HCCI combustion with residual gas trapping. It was found that an optimum inlet valve timing could be found in order to minimize NOx emissions. When the valve timing is significantly advanced or retarded away from this optimum, NOx emissions increase due to the richer air / fuel ratios required for stable combustion. These richer conditions are necessary as a result of either the trapped residual gases becoming cooled in early backflow or because of lowering of the effective compression ratio. The paper also examines the feasibility of using inlet valve timing as a method of controlling the combustion phasing for boosted HCCI with residual gas trapping.

Dieseline combustion as a concept combines the advantages of gasoline and diesel by offline or online blending the two fuels. Dieseline has become an attractive new compression ignition combustion concept in recent years and furthermore an approach to a full-boiling-range fuel. High speed imaging with near-parallel backlit light was used to investigate the spray characteristics of dieseline and pure fuels with a common rail diesel injection system in a constant volume vessel. The results were acquired at different blend ratios, and at different temperatures and back pressures at an injection pressure of 100MPa. The penetrations and the evaporation states were compared with those of gasoline and diesel. The spray profile was analyzed in both area and shape with statistical methods. The effect of gasoline percentage on the evaporation in the fuel spray was evaluated.

The bio-fuel, 2,5 - dimethylfuran (DMF) is currently regarded as a potential alternative fuel to gasoline due to the development of new production technology. However, little is known about the flame behavior in an optical engine. In this paper, high speed imaging (with intensifier) was used during the combustion of DMF and its blends with gasoline and ethanol (D50, D85, E50D50 and E85D15) in an SI optical engine. The flame images from the combustion of each fuel were analyzed at two engine loads: 3bar and 4bar IMEP. For DMF, D50 and E50D50, two modes were compared: DI and PFI. The average flame shapes (in 2D) and the average flame speeds were calculated and combined with mass fraction burned (MFB) data. The results show that when using DMF, the rate of flame growth development and flame speed is higher than when using gasoline. The differences in flame speed between DMF and gasoline is about 10% to 14% at low IMEP.

Negative valve overlapping is widely used for trapping residual burned gas within the cylinder to enable controlled Homogeneous Charge Compression Ignition (HCCI). HCCI has been shown as a promising combustion technology to improve the fuel economy and NOx emissions of gasoline engines. While the importance of in-cylinder flow in the fuel and air mixing process is recognised, the characteristics of air motion with specially designed valve events having reduced valve lift and durations associated with HCCI engines and their effect on subsequent combustion are not yet fully understood. This paper presents an investigation in an optical engine designed for HCCI combustion using EGR trapping. PIV techniques have been used to measure the in-cylinder flow field under motored conditions and a quantitative analysis has been carried out for the flow characterisation with comparison made against the flow in the same engine with conventional valve strategies for SI combustion.

Diesel engines are the versatile power source and is widely used in passenger car and commercial vehicle applications. Environmental temperature conditions, fuel quality, fuel injection strategies and lubricant have influence on cold start performance of the diesel engines. Strategies to overcome the cold start problem at very low ambient temperature include preheating of intake air, coolant, cylinder block. The present research work investigates the effect of coolant temperatures on passenger car diesel engine’s performance and exhaust emission characteristics during the cold start at cold ambient temperature conditions. The engine is soaked in the -7°C environment for 6 hours. The engine coolant is preheated to the desired coolant temperatures of 10 and 20°C by an external heater and the start ability tests were performed.

Transient operation is frequently used by vehicle engines and the exhaust emissions from the engine are mostly higher than those under the steady station. An experimental study has been conducted to investigate the effect of various valve timings and spark timings on combustion characteristics and particle emissions from a modern 3.0-liter Gasoline Direct Injection (GDI) passenger car engine. The transient condition was simulated by load increase from 5% to 15% at a constant engine speed with different settings of valve timings and spark timings. The transient particle emission measurement was carried out by a Cambustion DMS500 particulate analyser. The combustion characteristics of the engine during transient operation including cycle-by-cycle combustion variations were analyzed. The time-resolved particle number, particulate mass and particle size distribution were compared and analyzed between different engine settings.

The main obstacle for the development of Homogeneous Charge Compression Ignition (HCCI) engines is the control of auto-ignition timing, and one key is to control the trapped gas temperature so as to enable the autoignition at the end of compression stroke. Using special valve mechanisms, very high residual gas mass fraction can be achieved to raise the charge temperature. Gas exchange process hence plays a crucial role in such HCCI engines because of its strong interaction with combustion. The modification of the gas exchange process in a 4-stroke automotive engine for HCCI combustion is not straightforward, since the engine must be able to operate across a considerably wide range of speeds and loads. Intake air temperatures and the valve mechanism need to be controlled in order to deliver optimal engine performance and fuel economy. This paper presents a modelling study of the combustion and gas exchange in a HCCI engine.

This paper focuses on supercharged HCCI engines employing internal EGR that is obtained by the use of negative valve overlap. In HCCI engines, the absence of throttling coupled with the use of high compression ratio to facilitate auto-ignition and with the use of lean mixtures result in improved fuel efficiency. High dilution is required to control the auto-ignition and it also results in reduction of the production of NOx. To compensate for the charge dilution effect, the method used to recover the loss of power is to introduce more air in to the engine which allows introducing also more fuel while maintaining high lambda. A supercharger is required to introduce the required amount of air into the engine. The modelling investigation performed with Ricardo WAVE® coupled with CHEMKIN® and experimental investigation for supercharged HCCI show significant improvement in terms of extension of load range and reduction of NOx over the naturally aspirated HCCI and also over SI operation.

This paper presents a modeling study of a gasoline HCCI engine using a single-zone and a multi-zone engine combustion models coupled with the CHEMKIN chemical kinetics solver for the closed part of the cycle. These combustion models are subsequently combined with a 1-D gas dynamics engine cycle simulation code which calculates the engine gas exchange to supply the boundary conditions for the in-cylinder simulation and also predicts engine performance. The simulated in-cylinder pressure history and charge composition at the time of exhaust valve opening are compared with the data from a parallel engine experimental project. Although the single-zone model is useful for parameter studies by predicting the trend of auto-ignition timing variations as the result of the effect of engine operating conditions, the matching of simulated and test data is good perhaps only if the mixture and temperature distributions in the cylinder are uniform.

Two premixed compression ignition modes for low octane gasoline are numerically investigated. The multiple premixed compression ignition (MPCI) mode is featured with a sequence of “spray- combustion- spray- combustion”, while the partially premixed compression ignition (PPCI) mode is a sequence of “spray- spray- combustion”. This paper compares the combustion process of the two modes using multi-dimensional CFD code, KIVA-3v, which can perform chemical reaction calculations for different fuels by a discrete multiple component (DMC) method. The fuel used for simulation consists of 58.5% i-C8H18 and 41.5% n-C7H16 in volume, and has the same RON and similar physical properties to straight-run naphtha used in the experiment. The engine operating condition is fixed at a 1600rpm and 0.7 MPa IMEP. The injection strategies for these two modes are different. All of the parameters in the simulation come from the single cylinder engine experiments.

The detection of needle displacement within a Common Rail injector is a crucial step to suitably characterize the behaviour of an injector. The needle motion is traditionally measured by means of an eddy current sensor. Apart from its high cost, scientific literature highlights its drawbacks, such as the introduction of mechanical weakness on the control piston as well as the electromagnetic disturbance affecting data acquisition. In order to provide an improved quality of signal, other solutions have been developed, which require a large number of components, leading to increased layout complexity. This layout can create a packing issue while mounting the sensor on the test rig. A novel sensor (UK Patent Application No.1819731.9) using fibre optic cable has been designed and built to overcome the limitations typically associated with needle displacement transducers.