Search Results

Diesel engine developers are continually striving to reduce harmful NOx emissions through various calibration and hardware strategies. One strategy being implemented in production Diesel engines involves utilizing cooled exhaust gas recirculation (EGR). Although there is a significant NOx reduction potential by utilizing cooled EGR, there are also several issues associated with it, such as EGR cooler fouling and a reduction in cooler effectiveness that can occur over time. The exact cause of these issues and many others related to cooler fouling are not clearly understood. One such unanswered issue or phenomenon that has been observed in both field tested and lab tested EGR coolers is that of a recovery in EGR cooler effectiveness after a shutdown or after cycling between various conditions.

Cooled exhaust gas recirculation (EGR) is widely used in diesel engines to control engine out NOx (oxides of nitrogen) emissions. A portion of the exhaust gases is re-circulated into the intake manifold of the engine after cooling it through a heat exchanger known as an EGR cooler. EGR cooler heat exchangers, however, tend to lose efficiency and have increased pressure drop as deposit forms on the heat exchanger surface due to transport of soot particles and condensing species to the cooler walls. In our previous work surface condensation of water vapor was shown to be successful in removing a significant portion of the accumulated deposit mass from various types of deposit layers typically encountered in EGR coolers. Significant removal of accumulated deposit mass was observed for “dry” soot only deposit layers, while little to no removal was observed for the deposit layers created at low coolant temperatures that consisted of both soot and condensed hydrocarbons (HC).

This study investigates the combustion and emissions of a compression ignition (CI) engine operating with mixtures of hydrogen (H₂) and carbon monoxide (CO) injected with the intake air. Hydrogen and carbon monoxide were chosen as the gaseous fuels, because they represent the main fuel component of synthesis gas, which can be produced by a variety of methods and feed stocks. However, due to varying feed stock and production mechanisms, syngas composition can vary significantly. It is currently unknown how a varying H₂/CO (syngas) ratio affects the cycle efficiency and gaseous emissions. The experiments were performed on an air-cooled, naturally aspirated, direct injection diesel engine. The engine was operated at 1800 RPM with a compression ratio of 21.2:1. Two load conditions were tested; 2 bar and 4 bar net indicated mean effective pressure (IMEPⁿ). For all test conditions the added syngas demonstrated lower cycle efficiency than the diesel fuel baseline.

Particle mass and size distribution measurements have been made on the exhaust of an Onan prechamber diesel engine. Seven fuels were examined: no. 1 and no. 2 diesel fuel, 40 and 50 cetane number secondary reference fuels, and no. 2 diesel fuel doped with three different concentrations of Lubrizol 565, a barium-based smoke suppressant. The no. 1 and no. 2 diesel fuels and the 50 cetane number reference fuels produced very similar emissions with emission indices in the range 0.3-1.3 mg (gm-fuel)-1 and volume mean diameters between .09 and 0.15 μm. The 40 cetane number reference fuel produced both smaller emission indices, 0.2 to 0.8 mg (gm-fuel)-1, and particle diameters, 0.03 to 0.09 μm. These reductions were apparently related to the longer ignition delay period of the 40 cetane number fuel, which allowed better mixing of the fuel and air prior to combustion.

Particle concentrations and size distributions were measured in the exhaust of a turbocharged, aftercooled, direct-injection, Diesel engine equipped with a ceramic filter (trap). Measurements were performed both upstream and downstream of the filter using a two-stage, variable residence time, micro-dilution system, a condensation particle counter and a scanning mobility particle sizer set up to count and size particles in the 7-320 nm diameter range. Engine operating conditions of the ISO 11 Mode test were used. The engine out (upstream of filter) size distribution has a bimodal, log normal structure, consisting of a nuclei mode with a geometric number mean diameter, DGN, in the 10-30 nm range and an accumulation mode with DGN in the 50-80 nm range. The modal structure of the size distribution is less distinct downstream of the filter. Nearly all the particle number emissions come from the nuclei mode, are nanoparticles (Dp < 50nm), and are volatile.

Diesel particles carry charges ranging from 1-5 units of elementary charge per particle. The charge is bipolar, i.e., there are approximately equal numbers of positively and negatively charged particles. The charge distribution with respect to size follows a high temperature, Boltzmann equilibrium relationship. The first part of this paper describes charge measurements made on diesel particles emitted by three different diesel engines, and postulates a charging mechanism. The second part of the paper is an examination of how this natural charge may be used to collect particles from the exhaust. The charge level produced by combustion is only slightly lower than the charge level produced by the corona discharge in a conventional electrostatic precipitator. Thus, a simple electrostatic precipitator without a corona section will collect diesel particles affectively.

A 1.9 liter Volkswagen TDI engine has been modified to accomodate the addition of hydrogen into the intake manifold via timed port fuel injection. Engine out particulate matter and the emissions of oxides of nitrogen were investigated. Two fuels,low sulfur diesel fuel (BP50) and soy methyl ester (SME) biodiesel (B99), were tested with supplemental hydrogen fueling. Three test conditions were selected to represent a range of engine operating modes. The tests were executed at 20, 40, and 60 % rated load with a constant engine speed o 1700 RPM. At each test condition the percentage of power from hydrogen energy was varied from 0 to 40 %. This corresponds to hydrogen flow rates ranging from 7 to 85 liters per minute. Particulate matter (PM) emissions were measured using a scaning mobility particle sizer (SMPS) and a two stage micro dilution system. Oxides of nitrogen were also monitored.

Diesel exhaust particle number concentrations and size distributions, as well as gaseous and particulate mass emissions, were measured during steady-state tests on a US heavy-duty engine and a European passenger car engine. Two fuels were compared, namely a Fischer-Tropsch diesel fuel manufactured from natural gas, and a US D2 on-highway diesel fuel. With both engines, the Fischer-Tropsch fuel showed a considerable reduction in the number of particles formed by nucleation, when compared with the D2 fuel. At most test modes, particle number emissions were dominated by nucleation mode particles. Consequently, there were generally large reductions (up to 93%) in the total particle number emissions with the Fischer-Tropsch fuel. It is thought that the most probable cause for the reduction in nucleation mode particles is the negligible sulphur content of the Fischer-Tropsch fuel. In general, there were also reductions in all the regulated emissions with the Fischer-Tropsch fuel.

The use of a corona-less electrostatic precipitator as a collection and agglomeration device for diesel soot has been investigated. It collects and grows diesel particles which are emitted in the submicron diameter range and grow into much larger particles. These larger particles may then be collected with a relatively simple inertial device. Previous testing of a full scale precipitator designed for a Caterpillar 3304 engine showed that the reduction in sub-micron sized mass from the engine was roughly 30 to 40%. Greater reductions were desired. A sub-scale electrostatic agglomerator was built to analyze in greater detail the behavior of an existing full scale device. Tests were designed to determine; the charged fraction of the particles from the engine used, the collection efficiency of the electrostatic agglomerator, the effect of geometry on collection efficiency, and the size distribution of the particles reentrained after electrostatic collection.

This paper describes the performance and emissions of a hydrogen-fueled, spark-ignited engine. An electronic control device, designed to provide the engine with a timed injection of the fuel, is shown to give high mean effective pressures and high efficiencies. The oxides of nitrogen from the exhaust gases have been analyzed and the mechanism for their formation is reviewed. The paper further describes an experiment with traces of hydrocarbons added to the hydrogen in an attempt to explain any additional phenomena that may be taking place during the combustion, such as “prompt NO” which is known to occur in hydrocarbon flames only. As it turns out, such additions have a negligible effect on the NOx formation in the region investigated.

This study examines the effect of a ceramic particle trap and a manganese fuel additive on the mutagenic activity and chemical composition of diesel exhaust particulate matter from a heavy-duty mining engine. Particles were collected by dilution tunnel sampling from a 4-cylinder, Caterpillar 3304, naturally-aspirated, indirect-injection engine operated at six steady-state conditions. Depending on engine load and speed the ceramic particle trap reduced the following emissions: particulate matter, 80 – 94%; soluble organic fraction (SOF), 83 – 95%; 1-nitropyrene, 94 – 96%; and SOF mutagencity, 72% (cycle-weighted average). When the Mn fuel additive was used without a ceramic particle trap the total cycle mutagenic activity emitted increased 7-fold, in part, due to elevated emissions of 1-nitropyrene.

Measurements of particle concentrations in one cylinder of a 1982 5.7 liter GM V-8 diesel engine have been made using a unique total cylinder sampling system. The first part of the paper is devoted to an examination of the performance of the sampling system. The role of blowoff and nucleation in the formation of sample artifacts is discussed. The remainder of the paper is devoted to the results of a study of the formation and removal of carbon particles during diesel engine combustion. Several operating conditions have been examined. The influence of injection timing, load, EGR, and oxygen addition on particle formation and removal has been investigated. The concentrations of volatile and nonvolatile particulate matter have been measured as a function of crankangle position. Particle formation begins 1-5 crankangle degrees (CAD) after the start of combustion.

In-cylinder and exhaust soot mass measurements have been made on a single-cylinder conversion of a 4-cylinder, 2.8 1, high-swirl, direct-injection diesel engine using a sampling system which allows dumping, diluting, quenching, and collecting the entire contents of the cylinder on a time scale o£ about 1 ms. Experiments have been performed at engine speeds of 1,000 and 1,500, and equivalence ratios, ϕ, of 0.4 and 0.7. Soot mass first appears shortly after top dead center and reaches a peak between 15 and 30 crankangle degrees after top dead center (CAD ATDC). After reaching its peak value, soot concentration decreases with increasing crankangle and approaches exhaust levels by 40-60 CAD ATDC. The time lag between the start of combustion and the first appearance of soot increases with ϕ and ranges from 0.2 to 1 ms. The initial rate of soot formation ranges from 0.26 to 0.30 mg ms−1 and varies little with speed or ϕ.

Experiments were performed to measure the number-weighted particle size distributions emitted from a gasoline direct injection (GDI) engine. Measurements were made on a late model vehicle equipped with a direct injection spark ignition engine. The vehicle was placed on a chassis dynamometer, which was used to load the engine to road load at five different vehicle speeds ranging from 15 - 100 km/hr. Dilution of the exhaust aerosol was carried out using a two-stage dilution system in which the first stage dilution occurs as a free jet. Particle size distributions were measured using a TSI 3934 scanning mobility particle sizer. Generally speaking, the presence of the additives did not have a strong, consistent influence on the particle emissions from this engine. The polyether amine demonstrated a reduction in particle number concentration as compared to unadditized base fuel.

This report describes tests of a fuel additive in a medium-duty, high-swirl, direct-injection diesel engine. The additive was found to have little influence on general combustion performance or on NOx emissions. On the other hand, it had a profound effect on particulate emissions. This was most clear under high load where particle emissions are highest. Here, when the engine was switched from running on the base fuel to the additive treated fuel, particle emissions at first increased and then fell to levels about 40% lower (by particle volume) than those initially produced by the base fuel. The additive had a long lasting effect. After running with the additive for about 25 hours, emission levels with the base fuel were only slightly higher than those with the additive treated fuel. We believe that the additive action is associated with a combination of cleaning and surface conditioning. More work should be done to understand the relative importance of these two mechanisms.

The formation of particles in the combustion chamber of a direct injection diesel engine has been studied with the use of the Total Cylinder Sampling Method. With this method, nearly the entire contents of the cylinder of an operating diesel engine can be quickly removed at various times during the combustion process. The particle mass and size distributions present in the sample can then be analyzed. If quenching of the combustion process is quick and complete, the resulting samples are representative of the particle mass and size distributions present in the cylinder near the time sampling begins. This paper discusses the effect of injection timing and piston bowl shape on the particle formation and oxidation. Example size distribution measurements are also shown. The particle concentrations in the cylinder were measured for three different injection timings with the standard piston installed in the engine.

Light absorption and scattering coefficients have been measured for particles emitted by two diesel engines; one direct injection and one indirect injection, operating over a range of speeds and loads. Integrating plate absorption measurements yield a specific absorption coefficient of 9.1 square meters per gram of non-volatile particulate matter at 550 nm wavelength. This absorption coefficient is inversely proportional to wavelength and independent of engine operating conditions or type. The scattering coefficient was simultaneously measured as 1.3 square meters per gram of undifferentiated particulate matter. These experimental results are shown to be in the range predicted by theoretical absorption and scattering calculations, which have been made for elongated carbon-void particles.

A unique system which allows sampling of the entire contents of one of the cylinders of a 5.7-liter V-8 indirect-injection diesel engine has been developed. An explosively actuated cutter ruptures a diaphragm in the combustion chamber and allows the contents of the cylinder to rush out and be subsequently diluted and quenched with cool nitrogen. Particles are collected with a high-volume impactor/filter system. This system has been used to collect a series of particle samples at crankangles ranging from 5 to 40 degrees after top dead center. Particle samples from the exhaust were also obtained. The samples have been extracted to determine the soluble organic fraction. These extracts have been analyzed for five polycyclic aromatic compounds: pyrene, fluoranthene, benz(a)pyrene, benz(k)fluoranthene, and 1-nitropyrene. The results indicate significant removal of the first four between the combustion chamber and the exhaust manifold.

Nanoparticle formation during exhaust sampling and dilution has been examined using a two-stage micro-dilution system to sample the exhaust from a modern, medium-duty diesel engine. Growth rates of nanoparticles at different exhaust dilution ratios and temperatures have been determined by monitoring the evolution of particle size distributions in the first stage of the dilution system. Two methods, graphical and analytical, are described to determine particle growth rate. Extrapolation of size distribution down to 1 nm in diameter has been demonstrated using the graphical method. The average growth rate of nanoparticles is calculated using the analytical method. The growth rate ranges from 6 nm/sec to 24 nm/sec, except at a dilution ratio of 40 and primary dilution temperature of 48 °C where the growth rate drops to 2 nm /sec. This condition seems to represent a threshold for growth. Observed nucleation and growth patterns are consistent with predictions of a simple physical model.

Four-way, integrated, diesel emission control systems that combine selective catalytic reduction for NOx control with a continuously regenerating trap to remove diesel particulate matter were evaluated under real-world, on-road conditions. Tests were conducted using a semi-tractor with an emissions year 2000, 6-cylinder, 12 L, Volvo engine rated at 287 kW at 1800 rpm and 1964 N-m. The emission control system was certified for retrofit application on-highway trucks, model years 1994 through 2002, with 4-stroke, 186-373 kW (250-500 hp) heavy-duty diesel engines without exhaust gas recirculation. The evaluations were unique because the mobile laboratory platform enabled evaluation under real-world exhaust plume dilution conditions as opposed to laboratory dilution conditions. Real-time plume measurements for NOx, particle number concentration and size distribution were made and emission control performance was evaluated on-road.