Search Results

Side force has an influence on the behaviour of passenger cars in windy conditions. It increases approximately linearly with yaw angle over a significant range of yaw for almost all cars and the side force derivative, (the gradient of side force coefficient with yaw angle), is similar for vehicles of a given category and size. The shape factors and components which affect side force for different vehicle types are discussed. The dominant influence on side force, for most cars, however, is shown to be the vehicle height which is consistent with slender wing theory if the car and its mirror image are considered. This simple theory is shown to apply to 1-box and 2- box shapes, covering most MPVs, hatchbacks and SUVs, but does not adequately represent the side forces on notchback and fastback car shapes. Data from simple bodies is used to develop a modification to the basic theory, which is applied to these vehicle types.

It has been recognised that the ideal flow conditions that exist in the modern automotive wind tunnel do not accurately simulate the environment experienced by vehicles on the road. This paper investigates the effect of varying one flow parameter, freestream turbulence, and a single shape parameter, leading edge radius, on aerodynamic drag. The tests were carried out at model scale in the Loughborough University Wind Tunnel, using a very simple 2-box shape, and in the MIRA Full Scale Wind Tunnel using the MIRA squareback Reference Car. Turbulence intensities up to 5% were generated by grids and had a strong effect on transcritical Reynolds number and Reynolds sensitivity at both model scale and full scale. There was a good correlation between the results in both tunnels.

Significant aerodynamic drag reduction is obtained on a bluff body by tapering the rear body. In the 1930’s it was found that a practical low drag car body could be achieved by cutting off the tail of a streamlined shape. The rear end of a car with a truncated tail is commonly referred to as a Kamm back. It has often been interpreted as implying that the drag of this type of body is almost the same as that for a fully streamlined shape. From a review of the limited research into truncated streamlined tails it is shown in this paper that, while true for some near axisymmetric bodies, it is not the case for many more car-like shapes. For these shapes the drag reduction from an elongated tail varies almost linearly with the reduction in cross section area. A CFD simulation to determine the drag reduction from a truncated streamlined tail of variable length on the simple Windsor Body is shown by way of confirmation.

Vehicles on the road operate in the turbulent flow field resulting from the combined effects of the natural wind and the wakes of other vehicles. While substantial data exists on the properties of the natural wind, much less information is available for the wake properties of road vehicles. The wake information available for road vehicle shapes is mainly restricted to the near wake region, but to understand the vehicle operating environment it is the wake downstream of this region which is of interest. To determine the range of this area of interest requires some knowledge of the decay of the wake properties. From wind tunnel studies using small simple bluff bodies in free stream and in ground proximity the principle wake properties, velocity deficit and peak turbulence intensity have been measured. The maximum velocity deficit is shown to approximately decay with x-2/3, where x is the distance downstream, while turbulence intensity decays at a slightly slower rate.

The vortex structure in the wake of a car creates drag. In the case of a simple wing this drag component is well defined as a function of lift, but for road vehicles the relationship is more complex. The backlight surface has been shown to be a significant source of vortex drag and in this paper the influence of backlight aspect ratio on both vortex and base drag is investigated. The vortex drag factor is found to be independent of aspect ratio, while the base drag component is shown to be dependent on the ratio of base to frontal area.

The aerodynamic development of cars is conventionally carried out in the wind tunnel with the working section floor representing the ground surface. While recognising that the boundary conditions are false it has generally been assumed that this basic ground simulation is adequate for road cars. This situation is currently being reappraised. In this investigation a simple 1/4 scale car model has been tested in the MIRA Model Wind Tunnel, using both moving and stationary belt to represent the ground surface. The body and wheel drag contributions were measured independently. The influence of rear body shape, front spoilers, cooling airflow, and underfloor roughness on the aerodynamic characteristics, for both ground conditions has been assessed.