Refine Your Search

Date

Date

Topic

Topic

Forming Steel Parts Alloys SAE IC Powertrain Steering Committee Safety Magnesium alloys

Search Results

Viewing 1 to 20 of 105
123Next >Last >>
Sort by title
Standard

APPLICATION GUIDE TO RADIAL LIP SEALS
1991-10-01
HISTORICAL
J946_199110
This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.
Standard

Application Guide to Radial Lip Seals
2002-10-25
CURRENT
J946_200210
This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.
Standard

Automatic Transmission Hydraulic Control Systems - Terminology
2011-06-13
CURRENT
J648_201106
The following is a list of the most common terminology used in describing hydraulic control systems. The hydraulic control system of an automatic transmission may include oil pumps, pressure regulator, governor, and control valves.
Standard

DESIGN GUIDE FOR FORMED-IN-PLACE GASKETS
1988-05-01
HISTORICAL
J1497_198805
This manual presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.
Standard

DESIGN GUIDE FOR FORMED-IN-PLACE GASKETS
1988-12-01
HISTORICAL
J1497_198812
This manual presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.
Standard

DIESEL SMOKE MEASUREMENT PROCEDURE
1988-09-01
HISTORICAL
J35_198809
The recommended practice applies to the dynamometer test procedure which can be used to assess the smoke emission characteristics of vehicular diesel engines. In particular, this procedure describes the smoke test cycle, equipment and instrumentation, instrument checks, chart reading and calculation for evaluation of an engine’s transient smoke emission characteristic. In addition, this procedure offers guidelines to be used in establishing correlation between full flow in-line and end-of-line opacimeters. Since the type of test described here is transient in nature, a fast responding full flow opacimeter is required for the smoke measurements. Slow responding or sampling, or both, type instruments must not be used since they typically have excessive and variable response delays and do not provide an accurate measurement of an engine’s transient smoke characteristics.
Standard

Design Guide for Formed-in-Place Gaskets
2008-07-08
CURRENT
J1497_200807
This SAE Recommended Practice presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.
Standard

ENGINE AND TRANSMISSION DIPSTICK MARKING
1995-06-29
HISTORICAL
J614_199506
This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.
Standard

ENGINE COOLANT PUMP SEALS
1990-06-01
HISTORICAL
J780_199006
This SAE standard outlines physical dimensions and nomenclature for the sizes of seals commonly used in engine coolant pumps of automotive type engines. Its purpose is to define a standard envelope to accommodate installation of various seal designs and to promote uniformity in seal nomenclature.
Standard

ENGINE FOOT MOUNTING (FRONT AND REAR)
1995-07-03
HISTORICAL
J616_199507
This SAE Recommended Practice covers foot type mounting dimensions for engines intended for installation on subbases Table 1 and Figure 1.
Standard

ENGINE FOOT MOUNTING (FRONT AND REAR)
1978-06-01
HISTORICAL
J616C_197806
This recommended practice covers foot type mounting dimensions for engines intended for installation on sub-bases.
Standard

ENGINE MOUNTINGS
1985-07-01
HISTORICAL
J615_198507
This SAE Standard defines engine mounting dimensions for industry standardization and interchangeability. Table 1 and Fig. 1 are dimensions for arm type mountings. Table 2 and Fig. 2 are for side pad mountings. For engine housing SAE flange dimensions, see SAE J617. For engine foot type mountings (front and rear), see SAE J616.
Standard

ENGINE MOUNTINGS
1991-04-01
HISTORICAL
J615_199104
This SAE Standard defines engine mounting dimensions for industry standardization and interchangeability. Table 1 and Figure 1 are dimensions for arm type mountings. Table 2 and Figure 2 are for side pad mountings. For engine housing SAE flange dimensions, see SAE J617. For engine foot type mountings (front and rear), see SAE J616.
Standard

ENGINE MOUNTINGS
1995-07-03
HISTORICAL
J615_199507
This SAE Standard defines engine mounting dimensions for industry standardization and interchangeability. Table 1 and Figure 1 are dimensions for arm type mountings. Table 2 and Figure 2 are for side pad mountings. For engine housing SAE flange dimensions, see SAE J617. For engine foot type mountings (front and rear), see SAE J616.
123Next >Last >>
X