Search Results

The purpose of this study was to investigate approaches evaluating the performance of safety systems in crash tests and by analytical simulations. The study was motivated by the need to consider the adequacy of injury criteria and tolerance levels in FMVSS 208 measuring safety performance of restraint systems and supplements. The study also focused on additional biomechanical criteria and performance measures which may augment FMVSS 208 criteria and alternative ways to evaluate dummy responses rather than by comparison to a tolerance level. Additional analysis was conducted of dummy responses from barrier crash and sled tests to gain further information on the performance of restraint systems. The analysis resulted in a new computer program which determined several motion and velocity criteria from measurements made in crash tests.

The causes for 131 fatal crashes of lap-shoulder belted occupants were analyzed for crash causation and avoidance opportunities. Fourteen crash scenarios were determined to depict the situation and circumstance of the accidents. Each scenario is discussed in relation to driver age, actions, behavior, errors and aggressiveness, as well as crash type and other factors influencing the crash. Nearly a third of crashes involved a rapid, unpredictable onset by reckless action or mistake of another driver. The remainder were caused by the driver of the case-vehicle. Some were single vehicle crashes primarily related to excessive speed, aggressive driving, and drifting out of lane. The others were multi-vehicle crashes due primarily to inadvertent errors. The most common errors were right-of-way violations at an intersection, loss of control on wet roads, impact of a stationary vehicle, and lane changing errors.

The primary purpose of this parameter study was to carefully document occupant dynamics in well-controlled sled tests for comparison with simulated responses from the MVMA-2D analytical model. The test involved a Part 572 dummy exposed to a frontal deceleration while on a bucket seat and restrained by a lap-shoulder belt system. The length of belt webbing was incrementally increased from a snug configuration by as much as 30 cm. The addition of webbing increased the forward excursion, velocity, and acceleration of the head, chest, and hip without affecting the peak tension in the belt segments of the restraint system. Belt tension was identified as a poor measure of the horizontal load on the chest due to significant reaction forces in the lateral and vertical direction at the belt anchorages.

Sled tests were conducted at farside oblique angles of 15°, 45°, and 75° with a Part 572 dummy restrained by a conventional driver lap/shoulder belt system or a preinflated driver inflatable restaint. Occupant dynamics were compared in similar tests where an inboard energy absorbing lateral restraint of the upper torso was or was not used. It can be concluded that the seat wing improves the control of the dummy's dynamics in oblique impacts by directing the occupant's motion more forward into the restraint system, thereby taking more advantage of the restraining potential of the shoulder belt or inflatable restraint in controlling the deceleration of the dummy and enhancing the benefit of the restraint system. However, additional factors associated with the use of a seat wing remain to be investigated including the effect of impact force on the occupant, interaction with out-of-position occupants and comfort/convenience.

Objective: This study analyzes rear sled tests with a 95th% male and 5th% female Hybrid III dummy in various seating positions on ABTS (All Belt to Seat) seats in severe rear impact tests. Dummy interactions with the deforming seatback and upper body extension around the seat frame are considered. Methods: The 1st series involved an open sled fixture with a Sebring ABTS seat at 30 mph rear delta V. A 95th% Hybrid III dummy was placed in four different seating positions: 1) normal, 2) leaning inboard, 3) leaning forward and inboard, and 4) leaning forward and outboard. The 2nd series used a 5th% female Hybrid III dummy in a Grand Voyager body buck at 25 mph rear delta V. The dummy was leaned forward and inboard on a LeSabre ABTS or Voyager seat. The 3rd series used a 5th% female Hybrid III dummy in an Explorer body buck at 26 mph rear delta V. The dummy was leaned forward and inboard on a Sebring ABTS or Explorer seat.

Various surrogates and responses are available for study of the impact performance of energy absorbing steering systems in the laboratory. The relative influence of the SAE J-944 body block, the Part 572 dummy, and the GM Hybrid III dummy and of the associated thoracic responses were investigated for steering assembly impact in a series of sled tests. Not only did response amplitudes differ among the surrogates but more importantly trends in impact performance associated with modifications of the steering assembly depended on the choice of surrogate and response. The Hybrid III dummy was judged the best of the tested surrogates for study of the steering system impact performance in the laboratory, based on its more humanlike construction, impact response and expanded measurement capacity.

Biomechanical surrogates are used in various forms to study head impact response in automotive applications and for assessing helmet performance. Surrogate headforms include those from the National Operating Committee on Standards for Athletic Equipment (NOCSAE) and the many variants of the Hybrid III. However, the response of these surrogates to loading at the chin and how that response may affect the loads transferred from the jaw to the rest of the head are unknown. To address part of that question, the current study compares the chin impact response performance of select human surrogates to that of the cadaver. A selection of Hybrid III and NOCSAE based surrogates with fixed and articulating jaws were tested under drop mass impact conditions that were used to describe post mortem human subject (PMHS) response to impacts at the chin (Craig et al., 2008). Results were compared to the PMHS response with cumulative variance technique (Rhule et al., 2002).

The study was directed toward improving our understanding how postcrash column compression and steering wheel deformation relate to the driver interaction with an energy absorbing steering system during automotive collisions. Frontal sled tests conducted at 19–37 km/h investigated the Part 572 antropomorphic dummy interaction with a ball-sleeve column steering assembly over a range of column angles and surrogate postures. Neither column compression nor steering wheel deformation correlated with the mechanical severity of the test surrogate interaction with the steering system. The steering wheel deformed before the column compressed and the degree of wheel deformation strongly depended on the surrogate load distribution, the steering wheel being an important energy absorbing element.

Active head restraints are being used to reduce the risk of whiplash in rear crashes. However, their evaluation in laboratory tests can vary depending on the injury criteria and test dummy. The objective of this study was to conduct barrier tests with BioRID and sled tests with Hybrid III to determine the most meaningful responses related to whiplash risks in real-world crashes. This study involved: (1) twenty-four rear barrier tests of the Saab 9000, 900, 9-3 and 9-5 with two fully instrumented BioRID dummies placed in the front or rear seats and exposed to 24 and 48.3 km/h barrier impacts, and (2) twenty rear sled tests at 5-38 km/h delta V in three series with conventional, modified and SAHR seats using the Hybrid III dummy. A new target superposition method was used to track head displacement and rotation with respect to T1. Insurance data on whiplash claims was compared to the dummy responses.

The objective of this study was to analyze available anthropomorphic test device (ATD) responses from FMVSS 301-type rear impact tests. Rear impact test data was obtained from NHTSA and consisted of dummy responses, test observations, photos and videos. The data was organized in four test series: 1) NCAP series of 30 New Car Assessment Program tests carried out at 35 mph with 1979-1980 model year vehicles, 2) Mobility series of 14 FMVSS 301 tests carried out at 30 mph with 1993 model year vehicles, 3) 301 MY 95+ series of 79 FMVSS 301 tests carried out at 30 mph with 1995-2005 model year vehicles and 4) ODB series of 17 Offset Deformable Barrier tests carried out at 50 mph with a 70% overlap using 1996-1999 model year vehicles. The results indicate very good occupant performance in yielding seats in the NCAP, Mobility and 301 MY 95+ test series.

Previous pendulum impact tests have shown that knee joint injuries and tibial-fibular fractures may occur when loads are directed against the lower leg rather than directly against the femur in the knee. In order to further improve our understanding of lower extremity restraint mechanics, simulated frontal barrier crash experiments were conducted with unembalmed human cadavers and an anthropomorphic dummy restrained by a two-point shoulder belt. In the first test, an experimental bolster was specifically positioned so that the cadaver's lower leg would strike the bolster, thus inducing restraining loads entirely below the knee joint. The analysis of occupant kinematics showed that the flexed knee rode over and forward of the low-positioned bolster. Restraint induced considerable shearing load across the knee joint. Bolster measurements indicated a peak load of approximately 4.0 kN per leg which resulted in a contralateral central tear of the posterior cruciate ligaments.

Objective: This study analyzed available rear impact sled tests with Starcraft-type seats that use a diagonal belt behind the seatback. The study focused on neck responses for out-of-position (OOP) and in-position seated dummies. Methods: Thirteen rear sled tests were identified with out-of-position and in-position 5 th , 50 th and 95 th Hybrid III dummies in up to 47.6 mph rear delta Vs involving Starcraft-type seats. The tests were conducted at Ford, Exponent and CSE. Seven KARCO rear sled tests were found with in-position 5 th and 50 th Hybrid III dummies in 21.1-29.5 mph rear delta Vs involving Starcraft-type seats. In all of the in-position and one of the out-of-position series, comparable tests were run with production seats. Biomechanical responses of the dummies and test videos were analyzed.

This study analyzed FMVSS 301 rear impact tests with an instrumented rear-seat dummy. NHTSA conducted 15 FMVSS 301 rear crash tests with an instrumented and belted 50th Hybrid III dummy in the rear seat. In series 1, there were three repeat tests with the Jeep Liberty and two others, but no onboard camera view. In series 2, there were 8 tests with 2003-2005 MY (model year) vehicles that had rear head restraints. In series 3, there were two tests with 2004-2005 MY vehicles that did not have rear head restraints. There was an onboard camera view of the rear occupant in series 2 and 3. The dummy responses were evaluated and compared to relevant IARVs (injury assessment reference values). Based on the HRMD, the average height of the rear head restraints was 80.4 ± 3.4 cm (31.6″ ± 1.3″) above the H-point. In series 1, the delta V was 24.4 ± 2.0 km/h (15.2 ± 1.3 mph).

This sled test series involved occupant loading of the seat in rear crashes of 4.3-8.3 m/s (9.6-18.5 mph). The tests were conducted in the early 1980s and involved an unbelted or lap-shoulder belted Part 572 dummy in rear and oblique rear impacts. The research is reported today to provide comparative data for the record and serves as a control benchmark for more current technologies and safety research methodologies on seat performance in rear crashes. Safety belts improved occupant retention on the seat primarily by the lap belt reducing the upward and rearward movement of the pelvis. Tests were also conducted on the mechanisms for energy absorption by seatback deflection.

Role of the Seat in Rear Crash Safety addresses the historic debate over seatback stiffness, energy absorbing yielding, occupant retention and whiplash prevention; and it provides a scientific foundation for the direction GM pursued in the development and validation of future seat designs. It also describes the multi-year research study into the role of the seat in rear crash safety - first by addressing the need for occupant retention in the more severe rear crashes; and then by addressing the needs for an adequately positioned head restraint and changes in the compliance of the seatback to lower the risks of the whiplash in low-speed crashes.

The objective of this study was to analyze available anthropomorphic test device (ATD) responses from KARCO rear impact tests and to evaluate an injury predictive model based on crash severity and occupant weight presented by Saczalski et al. (2004). The KARCO tests were carried out with various seat designs. Biomechanical responses were evaluated in speed ranges of 7-12, 13-17, 18-23 and 24-34 mph. For this analysis, all tests with matching yielding and stiff seats and matching occupant size and weight were analyzed for cases without 2nd row occupant interaction. Overall, the test data shows that conventional yielding seats provide a high degree of safety for small to large adult occupants in rear crashes; this data is also consistent with good field performance as found in NASS-CDS. Saczalski et al.'s (2004) predictive model of occupant injury is not correct as there are numerous cases from NASS-CDS that show no or minor injury in the region where serious injury is predicted.

Belt interaction with the dummy's chest or pelvis was investigated during simulated frontal decelerations to develop a better understanding of the mechanics of belt restraint. Hyge sled tests were conducted at acceleration levels of 6-16 g's with a Part 572 dummy forward facing on an automotive bucket seat. Dynamics were compared in similar tests where the dummy was restrained by a conventional shoulder belt or belt segments attached to a modified sternum - a steel sternum with extensions for fixed belt attachments. Tests were also conducted with a conventional lap belt or belt segments fixed to an extension of the H point. Deformation characteristics of the standard and modified thorax were determined for a lateral and superior point load or a belt yoke compression of the sternum. The pelvic structure was also compressed by a lap belt. Our evaluation of test dummy dynamics indicates the following sequence of events with a conventional shoulder belt: 1.)