Search Results

The paper presents a failsafe strategy conceived for a Vehicle Dynamics Control (VDC) system developed by the Vehicle Dynamics Research Team of Politecnico di Torino. The main equations used by the failsafe algorithm are presented, especially those devoted to estimate steering wheel angle, body yaw rate and lateral acceleration, each of them fundamental to correctly actuate the VDC. The estimation is based on redundancy; each formula is considered according to a weight depending on the kind of maneuver. A new recovery algorithm is presented, which does not deactivate VDC after a sensor fault, but substitutes the sensor signal with the virtually estimated value. The results obtained through simulation are satisfactory. First experimental tests carried out on a ABS/VDC test bench of the Vehicle Dynamics Research Team of Politecnico di Torino confirmed the simulation results.

This article deals with a novel 2-speed transmission system specifically designed for electric axle applications. The design of this transmission permits seamless gearshifts and is characterized by a simple mechanical layout. The equations governing the overall system dynamics are presented in the paper. The principles of the control system for the seamless gearshifts achievable by the novel transmission prototype - currently under experimental testing at the University of Surrey and on a prototype vehicle - are analytically demonstrated and detailed through advanced simulation tools. The simulation results and sensitivity analyses for the main parameters affecting the overall system dynamics are presented and discussed.

This paper discusses the torque-fill capability of a novel hybrid electric drivetrain for a high-performance passenger car, originally equipped with a dual-clutch transmission system, driven by an internal combustion engine. The paper presents the simulation models of the two drivetrains, including examples of experimental validation during upshifts. An important functionality of the electric motor drive within the novel drivetrain is to provide torque-fill during gearshifts when the vehicle is engine-driven. A gearshift performance indicator is introduced in the paper, and the two drivetrain layouts are assessed in terms of gearshift quality performance for a range of maneuvers.

Chassis Control Systems development methodology is nowadays strongly based on analyzing performance by using PC vehicle dynamics simulation. Generally, the overall design, test bench and road validation process is continuously accompanied by simulation. The Base Model Simulator was developed by the Vehicle Dynamics Group at the Department of Mechanics of Politecnico di Torino both to satisfy this requirement and for educational purposes. It considers a complete vehicle dynamics mathematical model, including driver, powertrain, driveline, vehicle body, suspensions, steering system, brakes, tires. The Base Model Simulator takes in account the suspensions system elastokinematics, including, for example, automatic computation of camber variation during the vehicle roll motions. Tire model considered are either Pacejka's models or experimental data.

An improved block-oriented simulation methodology of vehicle air conditioning systems has been developed, based on dynamic and thermodynamic formulations of automotive components. The method applied considers any system as dynamic and the steady-state as a particular condition reached during transient states. Therefore it is necessary for every component of the system to define the dynamic laws, the dynamic constants and to impose the initial conditions. A few examples of modeled components are described in order to show the consistency of the thermodynamic differential approach and input/output relations between subsystems. An alternative approach of experimental look-up tables with respect to the thermodynamic differential method has also been applied, whenever it was convenient in terms of calculation improvements.

Vehicles equipped with Automated Manual Transmissions (AMT) for gear shift control show many advantages in terms of reduction of fuel consumption and improvement of driving comfort and shifting quality. In order to increase both performance and efficiency, an important target is focused on the minimization of the typical torque interruption during the gear shift, especially in front of the conventional automatic transmission. Recently, AMT are proposed to be connected with planetary gears and friction brakes, in order to reduce the torque gap during the gear change process. This paper is focused on a block-oriented simulation methodology developed in Matlab/Simulink/Stateflow® environment, able to simulate the performance of a complete FWD powertrain and in particular to predict dynamic performance and overall efficiency of the AMT with innovative Torque Gap Filler devices (TGF).

The paper presents linear and non-linear driveline models for Heavy Goods Vehicles (HGVs) in order to evaluate the main parameters for optimal tuning, when considering the drivability. The implemented models consider the linear and non-linear driveline dynamics, including the effect of the engine inertia, the clutch damper, the driveshaft, the half-shafts and the tires. Sensitivity analyses are carried out for each driveline component during tip-in maneuvers. The paper also analyses the overall frequency response using Bode diagrams and natural frequencies. It is demonstrated that the most basic model capable of taking into account the first order dynamics of the driveline must consider the moments of inertia of the engine, the transmission and the wheels, the stiffness and the damping properties of the clutch damper, driveshaft and half-shafts, and the tires (which link the wheel to the equivalent inertia of the vehicle).

The paper presents the research activity managed to investigate the dynamics of a 4WD vehicle equipped considering drivelines with different layout. The procedure developed required to conceive an on purpose simulator to compare performance through virtual experimentation. Drivelines mechanical main characteristics and performance increasing due to control strategy were evaluated. Preliminary road test were performed with a single driveline layout, to evaluate simulation reliability and limits. The paper presents the 4WD vehicle simulator, the main equations applied to model open, torque sensing and limited slip differentials, some preliminary road test results showing torque sensing driveline performance.

The paper presents the driveline models conceived by the author in order to evaluate the main parameters for an optimal tuning of the driveline of a passenger vehicle. The paper deals with a full modal analysis of the contributions of the different parts. The implemented models permit to consider the non-linear driveline dynamics, including the effect of the clutch damper (in terms of non-linear stiffness and variable amplitude hysteresis in the case of the models in the time domain) and the halfshafts, the engine mounting system and the tires. The influence of each component of the driveline on the overall frequency response of the system is presented. In particular, the paper demonstrates that the tire can be modeled like a non-linear damper within the rotational dynamics of the driveline and that it is the fundamental component contributing to the first order dynamics of the transmission.

E-mobility is a game changer for the automotive domain. It promises significant reduction in terms of complexity and in terms of local emissions. With falling prices and recent technological advances, the second generation of electric vehicles (EVs) that is now in production makes electromobility an affordable and viable option for more and more transport mission (people, freight). Current e-vehicle platforms still present architectural similarities with respect to combustion engine vehicle (e.g., centralized motor). Target of the European project EVC1000 is to introduce corner solutions with in-wheel motors supported by electrified chassis components (brake-by-wire, active suspension) and advanced control strategies for full potential exploitation. Especially, it is expected that this solution will provide more architectural freedom toward “design-for-purpose” vehicles built for dedicated usage models, further providing higher performances.

The first step toward a braking system ‘by wire’ is Electro-Hydraulic Braking System (EHB). The paper describes a method to evaluate through virtual experimentation the actual improvement in vehicle behaviour, from the point of view of both handling and comfort, including also pedal feeling, due to EHB. The first step consisted in modelling the hydraulic unit, comprehensive of sensors. Then it was conceived a control logic devoted to medium-low intensity braking manoeuvres, without ABS intervention, to determine an optimal braking force distribution and pedal feeling depending on the manoeuvre. A failsafe strategy, complete of on board diagnosis, to prevent dangerous system behaviour in the eventuality of a component failure was carried out and tested. Finally, EHB wheel pressure sensors were used to improve both ABS performance, increasing the adherence estimation, and Vehicle Dynamics Control (VDC) performance, through a more precise actuation.

The aim of this paper is the conception of a tire model which allows a good fit with the physical experimental behavior of the component. In the meanwhile, the model should be simple enough to permit real time vehicle dynamics simulation, in the same way as the diffused Pacejka's model. The paper discusses the influence of the model for the estimation of contact patch properties on the overall tire forces and moments. It demonstrates that unrealistic models of the contact patch can lead to a good fit with the experimental data (in terms of forces and self-aligning moment), even if the real physics of the tire is not reproduced. A realistic model implies a significant reduction of the stiffness of the brushes as a function of the vertical load between the tire and the road surface.

Over the last decade the simulation of driving cycles through longitudinal vehicle models has become an important stage in the design, analysis and selection of vehicle powertrains. This paper presents an overview of existing software packages, along with the development of a new multipurpose driving cycle simulator implemented in the Matlab/Simulink environment. In order to evaluate the performance of the simulator, a MAN TGL 12.240 multi-usage delivery vehicle was fitted with a CAN-bus data logger and used to create a series of ‘real-life’ drive cycles. These were inputted into the vehicle model and the simulated fuel mass flow-rate and engine rotational speed were compared to those experimentally obtained.

This paper presents an experimental methodology which can be adopted to measure the friction torque of the bearings in the wheel hubs of passenger vehicles. The first section of the paper highlights the reasons why an experimental device is necessary to have an objective evaluation of the performance of the bearing in terms of friction. In particular, the high level of approximation of the current formulas for the estimation of the friction inside a single bearing is discussed and demonstrated. An analytical methodology for the evaluation of the distribution of the axial load between the two bearings of the wheel hub is presented. However, its practical application for the precise calculation of the distribution of the load has to be checked through experimental tests.

The aim of this paper is to study in deep the peculiar test-rigs and experimental procedures adopted to the fulfilment of the principal requirements of automotive steel wheels, in particular regarding fatigue damaging. In the discussion, the standard requirements, the OEM specifications and the dimensional and geometric tolerances are approached. As result of an increasingly necessity to improve the performance of the components, innovative virtual test benches are presented. Differently from their traditional precursors, virtual test-rigs give an extended view of the physical behaviour of the component as the possibility to monitor stress-strain distribution in deep. In the first section, the state of the art and the specifications are listed. Secondly, the adopted hardware test-rigs as the experimental tests are described in detail. In the third one, proposed virtual test-rig is discussed.

The paper shortly describes an ABS/ESP Hardware-In-the-Loop (HIL) test bench built by the Vehicle Dynamics Team of the Department of Mechanics of Politecnico di Torino. It consists of a whole brake system, integrated through specific interface (e.g. wheel pressures signals) with a vehicle model running in real time on a dSPACE® board. Different commercial ABS strategies are compared, in a large spectrum of manoeuvres: slow brake apply manoeuvres, panic brake manoeuvres, μ-split brake manoeuvres, brake manoeuvres with a sudden variation of the friction coefficient between tyres and ground. The paper deals with the generation of all the signals required for activating a commercial ESP: steering wheel angle, body yaw rate, body lateral acceleration, engine control, etc… Some of them are transmitted by CAN. Typical handling manoeuvres are used to test the ESP: step steer, double step steer, ramp steer, etc… Several brake manoeuvres are simulated while turning.

The superior mobility of a military vehicle provides the combat crew with a tactical advantage through increased cross country speed. The suspension system plays a fundamental role in evaluating a vehicle mobility. A mathematical model that allows realistic simulations of vehicles operating in a wide spectrum of environmental conditions may help to lower costs and time required during their development. The paper concerns with vehicle-terrain interaction modeling, for a military tracked tank, through multi-body and block-oriented approaches. It is focused on the consequences that the suspension system has got on the comfort and on the performance. Thus through a multi-body software a realistic three dimensional model of a tracked fighting vehicle is developed. This virtual model confirms some experimental data available on its longitudinal dynamics. In order to simplify the multi-body simulations, a block-oriented approach is adopted to develop a model of the same vehicle.

The research presented in this paper focuses on the effects of downsizing the electric motor drive of a fully electric vehicle through the adoption of a multiple-speed transmission system. The activity is based on the implementation of a simulation framework in Matlab / Simulink. The paper considers a rear wheel drive case study vehicle, with a baseline drivetrain configuration consisting of a single-speed transmission, which is compared with drivetrains adopting motors with identical peak power but higher base speeds and lower peak torques coupled with multiple-speed transmissions (double and three-speed), to analyze the benefits in terms of energy efficiency and performance. The gear ratios and gearshift maps for each multiple-speed case study are optimized through a procedure developed by the authors consisting of cost functions considering energy efficiency and performance evaluation. The cost functions are explained in the paper along with the models adopted for the research.

This paper deals with the development of a Lap Time Simulator in order to carry out a first approximate evaluation of the potential benefits related to the adoption of the Kinetic Energy Recovery System (KERS). KERS will be introduced in the 2009 Formula 1 Season. This system will be able to store energy during braking and then use it in order to supply an extra acceleration during traction. Different technologies (e.g. electrical, hydraulic and mechanical) could be applied in order to achieve this target. The lap time simulator developed by the authors permits to investigate the advantages both in terms of fuel consumption reduction and the improvement of the lap time.

The paper describes the advantages due to the adoption of multi-speed transmission systems within fully electric vehicles. In particular, the article compares a conventional single-speed transmission layout, a 2-speed layout based on a novel gearbox architecture capable of seamless gearshifts, and a Continuously Variable Transmission layout. The selection of the optimal gear ratios for the 2-speed system has been based on an optimization procedure, taking into account the efficiency characteristics of the components of the whole vehicle powertrain. The control system for the Continuously Variable Transmission system has been designed with the aim of maximizing the efficiency of the operating points of the electric motor.