Search Results

By using empirical and semi-empirical relationships previously reported in the literature, non-linear viscoelastic properties of a number of lubricants have been determined from their linear viscoelastic behaviour, as measured by an oscillatory rheometer. Similarly to polymeric viscosity index improved (VII) lubricants, non-polymeric mineral blends were also shown to display viscoelastic behaviour. A general equation is suggested that allows the first normal stress difference which characterises the viscoelastic behaviour of lubricants to be expressed as a function of the shear viscosity.

Laser induced fluorescence (LIF) was used in the cylinder liner of a firing single-cylinder direct-injection diesel engine to characterise the development of the lubricant film during the first 200 engine cycles under cold-start conditions. The results have provided information on the rate of oil film development which has proved to be a highly unsteady process due to the complicated oil transport processes through the ring-pack.

Local measurements of the mean and rms velocities have been obtained by laser Doppler velocimetry in the coolant passages of a transparent model of a Ford 2.5L diesel cylinder head and block at a steady flowrate of 6.83 × 10-4 M3/s. The simulation of the coolant fluid by a mixture of hydrocarbon fluids at a predetermined constant temperature allowed accurate matching of the refractive index to that of the acrylic model, thus providing optical access for LDV measurements of the internal flow in sensitive areas where cooling is essential to prevent metal-fatigue failure. The results were obtained in sufficient detail to allow further validation of CFD coolant flow models.

A test-rig has been developed to simulate under idealised conditions the lubricating action between the piston-ring and the cylinder-liner in reciprocating engines. Complications arising in production engine piston-assemblies such as lubricant starvation, ring and piston dynamics, thermal and elastic deformations and blowby can thus be avoided so that the lubricant film characteristics are examined in isolation. The lubricant film thickness and friction at the piston-ring/liner interface were simultaneously measured throughout the stroke as a function of speed and load and compared with the solution of the Reynolds equation for a range of boundary conditions. The examined conditions included the Swift-Stieber (Reynolds), the separation and limiting cases of the Floberg and the Coyne & Elrod boundary conditions using a numerically efficient general purpose program.

Laser Doppler velocimetry, phase Doppler anemometry and Mie scattering were applied to a single-cylinder, four-valve, spark-ignition gasoline research engine equipped with a fully transparent liner and piston, to obtain information about the tumble flow and the droplet size and velocity distributions during induction and compression, for lean air/fuel mixture ratios of 17.5 and 24 and with closed-valve and open-valve fuel injection. The mixture distribution obtained with the two injection strategies was correlated with flame images, pressure analysis and exhaust emissions which confirmed the advantages of combining open-valve injection with tumble to allow stable and efficient engine operation at an air/fuel ratio of 24 through charge stratification and faster flame growth.

A diesel spray model has been developed and validated against experimental data obtained for different injection and surrounding gas conditions to allow investigation of the relative importance of the different physical processes occurring during the spray development. The model is based on the Eulerian-Lagrangian approximation and the Navier-Stokes equations, simulating the gas motion, are numerically solved on a collocated non-uniform curvilinear non-orthogonal grid, while the spray equation is solved numerically using a Lagrangian particle tracking method. The injection conditions are determined by another recently developed model calculating the flow in the fuel injection system, the sac volume and injection holes area which accounts for the details of the injection velocity, the fuel injection rate per injection hole and occurrence of hole cavitation. Thus, differences between the sprays from inclined multihole injectors can be simulated and analysed.

Direct flame imaging and pressure analysis were applied to the combustion of gasoline and compressed natural gas (CNG) in a single-cylinder, four-valve spark-ignition engine equipped with optical access via quartz windows in the cylinder liner and piston crown. Tests were performed at three engine speed/load conditions and at equivalence ratios of 1.0, 0.9 and 0.8. The four-valve head incorporated two different port geometries, with and without metal sleeves to deflect the intake air flow, in order to investigate the effect of tumble strength on combustion and engine-out emissions of unburned hydrocarbons and NOx. The results showed that sleeving of the intake ports produced a significant increase in IMEP and a reduction in CoV IMEP for both CNG and gasoline, due to the greatly reduced bum duration.

The in-cylinder flow during induction and compression in the pentroof chamber of a four-valve, single-cylinder, spark-ignition optical engine was quantified by LDV and correlated with combustion development especially under lean mixture conditions. The tumble-generating capacity of the cylinder head was first characterised by a tumble adaptor under steady flow conditions and, subsequently, enhanced by two sleeves introduced into the intake ports which generated a stronger tumbling motion.

Measurements of flow, spray, combustion and performance characteristics are reported for a Hydra direct-injection diesel, based on the Ford 2.5 L, engine and equipped with a variable-swirl port, a unit fuel injector and optical access through the liner and piston. The results provide links between the pre-combustion and combustion flow and, at the same time, between purpose-built single-cylinder optical engines and multi-cylinder production engines of nearly identical combustion chamber geometry. In particular, the spray penetration was found to depend on engine speed, rather than load, with velocities up to around 260 m/s at atmospheric pressure and temperature which are reduced by a factor of 2.5 under operating conditions and seem to be unaffected by swirl. The duration of combustion was reduced with increasing swirl and ignition delay increased linearly with engine speed.

An investigation into the spray structure generated by two swirl pressure atomisers under various operating conditions in a constant-volume chamber and the in-cylinder flow pattern in an optical research direct-injection gasoline engine has been performed using CCD camera and laser Doppler velocimetry, respectively. The results provided detailed information about the effect of back pressure on the spray structure generated by the two injectors and the in-cylinder flow field which the sprays encounter following fuel injection into the cylinder during the induction and compression strokes.

The in-cylinder flow, mixture distribution, combustion and exhaust emissions in a research, five-valve purpose-built gasoline engine are discussed on the basis of measurements obtained using laser Doppler velocimetry (LDV), fast spark-plug hydrocarbon sampling, flame imaging and NOx/HC emissions using fast chemiluminescent and flame ionisation detectors/analysers. These measurements have been complemented by steady flow testing of various cylinder head configurations, involving single- and three-valve operation, in terms of flow capacity and in-cylinder tumble strength.

Transient behavior of the engine is one of the most crucial factors for motorcycle features. Characterization of the fuel film with port fuel injection (PFI) is necessary to enhance this feature with keeping others, such as high output, low emissions and good fuel consumption. In order to resolve the complicated phenomena in real engine condition into simple physical issues, a simulated intake port was used in our research with Laser Induced Fluorescence (LIF) technique to allow accurate measurement of the fuel film thickness, complemented by visualization of the film development and spray behavior using high-speed video imaging. Useful results have been conducted from the parametric studies with various sets of conditions, such as injection quantity, air velocity and port backpressure.

Two optical single-cylinder spark-ignition engines equipped with two- and four-valve cylinder heads were used to examine the flow and flame interaction under lean mixture conditions. Images of the developing flame under quiescent, swirl, low tumble and high tumble flow conditions corresponding to a wide range of mean velocity and turbulence levels around the time of ignition were obtained with an image-intensified CCD camera using the light radiated by the flame and the flow in the vicinity of the spark plug was quantified by laser Doppler velocimetry. In the case of the tumbling flow, the flame images were software-processed to allow estimation of the total flame area, the displacement of its centre as a function of crank angle and their correlation with the cylinder pressure.

A transparent enlarged model of a six-hole injector used in the development of emerging gasoline direct-injection engines was manufactured with full optical access. The working fluid was water circulating through the injector nozzle under steady-state flow conditions at different flow rates, pressures and needle positions. Simultaneous matching of the Reynolds and cavitation numbers has allowed direct comparison between the cavitation regimes present in real-size and enlarged nozzles. The experimental results from the model injector, as part of a research programme into second-generation direct-injection spark-ignition engines, are presented and discussed. The main objective of this investigation was to characterise the cavitation process in the sac volume and nozzle holes under different operating conditions. This has been achieved by visualizing the nozzle cavitation structures in two planes simultaneously using two synchronised high-speed cameras.

A laser-induced fluorescence (LIF) system has been developed to obtain measurements of the instantaneous lubricant film thickness in the piston-cylinder assembly of a firing single-cylinder, direct-injection diesel engine. Measurements were made at top-dead-centre (TDC), mid-stroke and bottom-dead-centre (BDC) position by means of three fibre optic probes inserted into the cylinder liner and mounted flush with its surface. Following extensive repeatability tests, the cycle-averaged lubricant film thickness was estimated for different multi-grade oils as a function of engine speed, load and temperature. The results quantified the dependence of the film thickness ahead, under and behind the piston rings on oil chemistry and viscometric properties, thus confirming the important role of the LIF technique in the development and formulation of new engine oils.

Mixed-lubrication models comprising of Patir and Cheng's [1,2] average Reynolds equation and Greenwood and Tripp's [3] asperity interaction formulations have hitherto been widely used in predicting piston-ring performance. In this paper a number of models have been developed to allow mixed-lubrication of both Newtonian and shear thinning fluids to be simulated. Lubricating action usually involves two anisotropic solid surfaces of statistically different profiles. Various forms of the average Reynolds equation and the asperity interaction models require parameters representing the composite surface roughness and profile parameters at the contact. Here a strategy for determining these equivalent composite parameters is presented. Mathematical simulations indicate that when the composite RMS and composite summit RMS roughness of the contact approach the same value, the performance of the mix-lubrication model becomes dominated by the asperity interaction formulation.

The diesel engine is the most efficient user of fossil fuels for vehicle propulsion and seems to best fulfill the requirements of the future. It is for this reason that Volkswagen has initiated a very broad research programme for diesels. The purpose of this paper is to build a bridge between fundamental research and technical developments which could allow evaluation of the prospects of direct- injection diesels as powerplants of choice for passenger cars in the turn of the century. The current knowledge on mixture formation, combustion and pollutant formation in diesel engines is presented and discussed with special emphasis given to the concept of the direct-injection diesel engine.

A new simulation approach to the modeling of the whole fuel injection process within a common-rail fuel injection system for direct-injection gasoline engines, including the pressure-swirl atomizer and the conical hollow-cone spray formed at the nozzle exit, is presented. The flow development in the common-rail fuel injection system is simulated using an 1-D model which accounts for the wave dynamics within the system and predicts the actual injection pressure and injection rate throughout the nozzle. The details of the flow inside its various flow passages and the discharge hole of the pressure-swirl atomizer are investigated using a two-phase CFD model which calculates the location of the liquid-gas interface using the VOF method and estimates the transient formation of the liquid film developing on the walls of the discharge hole due to the centrifugal forces acting on the swirling fluid.

The origin and development of swirl center precession in engine flows has been investigated in a steady flow rig, with and without a porous plate simulating a stationary piston, and in a model engine motored at 200rpm; swirl, in all cases, was generated by means of 60° vanes located in the axisymmetric inlet port. The swirl center performs a helical motion that originates as an instability in the forced-vortex core from its interaction with the axial flow at a free stagnation point and develops in the engine from the piston towards the cylinder head; an opposite trend has been observed in the steady flow case with the open-ended cylinder. In the ensemble-averaged measurements, swirl center precession has been identified by the increased tangential velocity fluctuations around the off-centre zero swirl velocity.

The effect of inlet port design on swirl generation has been investigated for four helical ports from production, prototype and research Dl diesel engines by analyzing experimentally measured steady flow velocity distributions at the inlet valve curtain area and comparing their swirl characteristics in terms of the calculated in-cylinder angular momentum components and swirl ratio under operating conditions.