Refine Your Search

Date

Date

Topic

Topic

Seals and gaskets Tests and Testing Durability Quality, Reliability, and Durability Chassis MTC1, Earthmoving Machinery Regulations Noise

Search Results

Viewing 1 to 20 of 37
12Next >Last >>
Sort by title
Standard

Capacity Rating--Elevating Scrapers
2003-05-12
CURRENT
J957_200305
This SAE Standard specifies a procedure for approximating the volume of a typical material carried in the bowl of an elevating scraper as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and a representative volume on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

DRAWBAR TEST PROCEDURE FOR CONSTRUCTION, FORESTRY, AND INDUSTRIAL MACHINES
1986-05-01
HISTORICAL
J872_198605
This SAE Standard specifies a test method to measure the drawbar pull performance of self-propelled construction, forestry, and industrial machines and their combinations with mounted and/or trailed equipment, with or without payload, as listed in SAE J1116. It covers the following criteria measured against travel speed: drawbar pull, drawbar power, and wheel or track slip.
Standard

Drawbar Test Procedure for Construction, Forestry, and Industrial Machines
2003-05-08
CURRENT
J872_200305
This SAE Standard specifies a test method to measure the drawbar pull performance of self-propelled construction, forestry, and industrial machines and their combinations with mounted and/or trailed equipment, with or without payload, as listed in SAE J1116. It covers the following criteria measured against travel speed: drawbar pull, drawbar power, and wheel or track slip.
Standard

Earthmoving Machinery—Coupling of Attachments to Skid Steer Loaders
2000-06-28
HISTORICAL
J2513_200006
This SAE Standard sets forth standard dimension requirements for the loader attachment bracket and attachment interface to allow interchangeability of attachments on skid steer loaders whose operating mass (see SAE J/ISO 6165) is 4,500 kg or less. Narrow skid steer loaders may have a width that does not allow compliance with this standard. The design of the loader attachment bracket locking system is not restricted by this standard and is left to the discretion of the manufacturer.
Standard

Hydraulic Backhoe Lift Capacity
2012-05-11
CURRENT
J31_201205
This standard applies to hydraulically operated backhoes (as defined in SAE J1116) This standard describes a uniform "over end" and "full swing arc" lifting capacity rating for backhoes. It is based on the actual capacity of the machine to lift and support a load under stable conditions. Rated lift capacities will be specified for both the boom and the dipperstick and will be shown on a lift capacity chart Figure 1.
Standard

Hydraulic Excavator Lift Capacity Calculation and Test Procedure
2008-04-14
CURRENT
J1097_200804
This standard provides a uniform method to calculate and a test procedure to validate hydraulic excavator lift capacity. It establishes definitions and specifies machine conditions for calculations in Section 1 and identifies the validating test procedure in Section 2.
Standard

IDENTIFICATION TERMINOLOGY—PIPELAYERS
1980-06-01
HISTORICAL
J1295_198006
This standard applies to machines which are designed to raise, lower, and carry pipe and loads of similar nature. The term pipelayer does not include tractors or loaders with side booms which are optional attachments, manufacturer or dealer-installed, to machines as defined in SAE J1057. Note: Some related standards will apply equally to pipelayers and to tractors and loaders with side boom. Two such standards are SAE J743 and ANSI B30.14.
Standard

LOADING ABILITY TEST CODE--SCRAPERS
1985-11-01
HISTORICAL
J764_198511
The code applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.) The loading procedure is limited to standing starts in order to reduce the number of variables that are difficult to control and measure. Because of the difficulties in controlling some of the other variables, meaningful numerical comparison of time and load from scraper to scraper requires that data be taken at the same time and place, and that the units being compared be of approximately equal capacity.
Standard

LOADING ABILITY TEST CODE—SCRAPERS
1977-06-01
HISTORICAL
J764_197706
The code applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See J1116 and J1057a.) The loading procedure is limited to standing starts in order to reduce the number of variables that are difficult to control and measure. Because of the difficulties in controlling some of the other variables, meaningful numerical comparison of time and load from scraper to scraper requires that data be taken at the same time and place, and that the units being compared be of approximately equal capacity.
Standard

LOADING ABILITY TEST PROCEDURE—SCRAPERS
1995-08-01
HISTORICAL
J764_199508
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom
2011-12-08
CURRENT
J743_201112
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
12Next >Last >>
X