Search Results

An investigation was made into two approaches to air-fuel mixture formation in direct injection SI engines in which charge stratification is controlled by swirl or tumble gas motions, respectively. Particle image velocimetry (PIV), laser-induced fluorescence (LIF) and air-fuel ratio measurement by infrared absorption were used to analyze fuel transport from the fuel injector to the spark plug and the fuel vaporization process. The results obtained were then compared with measured data as to combustion stability. As a result, the reason why the effects of injection timing on combustion stability were different between the two approaches was made clear from the standpoint of the mixture formation process.

It is necessary to understand the entrainment process of ambient air into diesel sprays for the combustion process. This study focused on the entrainment process of non-combusting and combusting hydrogen jets instead of evaporated fuel sprays because of ease with measurement for fundamental research. Spatial and temporal changes of the air entrainment into the jets were obtained using flow visualization technique. The experimental results showed that the total air mass entrained into the flame jet is nearly equal to that into the cold jet. The rate of entrainment per unit area of the flame jet is smaller than that in the cold jet. When a transient jet is separated into side and front parts, the rate of air mass entrained from the front part of the jet decreases with time while the rate into the side of the jet per unit area is almost the same. The total air mass entrained into the jet can be approximately explained by the momentum theory.

Coherent anti-Stokes Raman spectroscopy (CARS) temperature measurements were performed in the unburned gas in a spark ignition engine. First, as the residual gas mass fraction is one of the factor that is known to cause to autoignition, the effect of the residual gas mass fraction on the unburned gas temperature is estimated. In order to control the residual gas mass fraction, a skip fired cycle method was used., and the single cylinder test engine used in this study was fueled with gasoline (89.9 RON). The residual gas causes the unburned gas temperature to rise by approximately 55 K and it also produces a large temperature variation on the order of ±20 K when expressed as a standard deviation. Second, the unburned gas temperature of the single cylinder test engine and the 4 valve production engine was measured under steady-state engine operation in order to compare the residual gas mass fraction of the test engine with that of the production engine.

The authors have previously proposed a plume ignition and combustion concept (i.e., PCC combustion), in which a hydrogen fuel is directly injected to the combustion chamber in the latter half of compression stroke and forms a richer mixture plume. By combusting the plume, both cooling losses and NOx formation are reduced. In this study, thermal efficiency was substantially improved and NOx formation was reduced with PCC combustion by optimizing such characteristics as direction and diameter of the jets in combination with combustion of lean mixture. Output power declined due to the lean mixture, however, was recovered by supercharging while keeping NOx emissions at the same level. Thermal efficiency was further improved by slightly re-optimizing the jet conditions.

The results of this study make clear the characteristics of electrode performance deterioration in terms of cell voltage reduction in polymer electrolyte fuel cells (PEFCs) caused by the presence of certain quantities of carbon monoxide and/or hydrogen sulfide in the anode feed. AC impedance measurements of the anode and cathode potentials revealed that both electrode potentials showed deterioration in the presence of each type of poisoning gas. This suggests that the poisoning gases permeated the electrolyte membrane and transferred to the cathode, causing performance deterioration by poisoning the catalyst. In addition, AC impedance measurements indicated that the presence of hydrogen sulfide in the anode feed increased the membrane impedance, thus implying some poisoning effect even on the electrolyte membrane.

This paper presents a study of mixture formation in the combustion chamber of a direct-injection SI engine. In-cylinder flow measurement was conducted using laser Doppler velocimetry (LDV) and particle image velocimetry (PIV), and visualization of fuel vapor behavior was done using laser-induced fluorescence (LIF). Further, fast response flame ionization detector (FID) was used to measure the hydrocarbon (HC) concentrations in the vicinity of the spark plug. Thereby mixture concentrations in the vicinity of the spark plug, within the mixture distribution observed using LIF, were quantified. Results revealed that an upward flow forms near the center of the cylinder in the latter half of the compression stroke and goes from the piston crown toward the cylinder head. This upward flow is caused by the synergistic effect of the swirl motion generated in the cylinder and the cylindrical bowl provided in the piston crown eccentrically to the central axis of the cylinder.

It is important to develop the technique for measuring the cycle-to-cycle variation of combustion in order to reduce the fuel consumption of the commercial spark ignition engine. In previous study, we had proposed using the spark plug as an ion probe to measure the appearance time of maximum pressure under the lean mixture conditions of the research engine. In this paper the combustion diagnostics for the commercial engine was performed using the spark plug as an ion probe. Under idling conditions the ion current often appeared during the exhaust process. This ion current is dominated by the flame contact area and the flame velocity. In this case there is good correlation between the characteristic value of the ion current and the indicated mean effective pressure (IMEP). Finally using the spark plug as an ion probe can detect the combustion quality under conditions with large cyclic variation.

A new technique for combustion diagnostics of a spark ignition engine was developed. In this method the ion sensor with the circular configuration was installed into the cylinder head gasket. This sensor is expected to be applied for production engine. The signal measured by the ion sensor was similar with that of cylinder pressure. The peak timing of ion current was consistent with the peak timing of pressure. There was a strong correlation between IMEP and the peak timing of ion current. This sensor is available to detect combustion quality in a spark ignition engine.

The results of our previous study showed that applying hydrogen (H2) to homogeneous charge compression ignition (HCCI) combustion with the assist of di-methyl ether (DME) as a supplement improved thermal efficiency compared with homogeneous hydrogen-fueled spark ignition (SI) combustion [1, 2]. As a general characteristic of HCCI combustion, however, stable engine operation is limited to a narrow region by the occurrence of misfiring and abrupt combustion like knocking. The onset of heat release is still not sufficiently controllable to achieve optimum engine performance. The objective of this study is to control the onset of the main heat release of hydrogen-fueled HCCI combustion by adopting spark ignition to assist autoignition. The results showed that improved thermal efficiency and reduced combustion fluctuation were achieved by attaining MBT operation with the support of spark ignition.

In order to reduce the exhaust emission and the fuel consumption in a spark ignition engine, the combustion diagnostics had been developed. However, there are few sensors which can detect the combustion quality for the individual cycle and cylinder in production engines. In previous study, the new technique using a gasket ion sensor for measuring the combustion quality has been proposed. In present study, the flame propagation pattern in a spark ignition engine was detected by using a gasket ion sensor with a circular electrode. The waveforms of ion current obtained from a circular ion sensor were compared with the flame propagation pattern obtained from multiple ion sensors. When the mixture was ignited in offset center of the cylinder, the flame propagation pattern was distorted from the spherical pattern. Then the waveforms of ion current from the circular ion sensor were varied from the waveform for a center ignition.

The planned development of a hydrogen ICE system for trucks is one of the technological candidates for air pollution reduction and global warming prevention for the large-sized (heavy-duty) trucks supporting Japanese freightage. This project is the first to develop a DISI multi-cylinder hydrogen ICE system aimed at combining high power output and low NOx generation.

It is well known that the wavelet transform is a useful time-frequency analysis method for an unsteady signal and major attention has been focused on the selection of the mother wavelet (MW) because the MW plays an important role in the wavelet transform. In this study, we analyze the pressure signal in a spark-ignition engine and the vibration of the engine block measured by a knock sensor under the knocking conditions when knocking is caused. We then propose a new method of the knocking detection that utilizes the knocking signal measured with a knock sensor as a MW. We call this method the Instantaneous Correlation Method (ICM). The degree of similarity between the MW and the vibration of the engine block was judged and only the knocking signal from the vibration of the engine block was extracted. The results obtained here show that the method proposed in this study is useful for knocking detection even if the engine speed is very high of 6000rpm.

A single cylinder, supercharged dual fuel gas engine with micro-pilot fuel injection is operated using methane only and methane-hydrogen mixtures. Methane only experiments were performed at various equivalence ratios and equivalence ratio of 0.56 is decided as the optimum operating condition based on engine performance, exhaust emissions and operation stability. Methane-hydrogen experiments were performed at equivalence ratio of 0.56 and 2.6 kJ/cycle energy supply rate. Results show that indicated mean effective pressure is maintained regardless of hydrogen content of the gaseous fuel while thermal efficiency is improved and presence of hydrogen reduces cyclic variations. Increasing the fraction of hydrogen in the fuel mixture replaces hydrocarbon fuels and reduces carbon monoxide and hydrocarbon emissions.

In order to investigate the relation between ion current and combustion characteristics, the ion current signal from a spark plug as an ion probe, pressure history and flame development were measured in a homogeneous propane-air mixture in closed combustion chambers. The flame propagation was measured by Schlieren photography technique. When negative bias is applied to the central electrode of the spark plug, the ion current flows only due to an early flame kernel existing near the spark plug. When positive bias is applied to the central electrode, the ion current flows from the central electrode to the combustion chamber wall and to the ground electrode. Consequently, the ion current is dominated by the contact area between the flame and the combustion chamber wall. The appearance period of ion-current is related to the combustion duration. This method was applied to the combustion analysis of the spark ignition engine.

Hydrogen is expected to be a clean and energy-efficient fuel for the next generation of power sources because it is CO2-free and has excellent combustion characteristics. In this study, an attempt was made to apply Homogeneous Charge Compression Ignition (HCCI) combustion to hydrogen with the aim of achieving low oxides of nitrogen (NOx) emissions and high fuel economy with the assistance of the di-methyl-ether (DME) fuel supplement. As a result, HCCI combustion of hydrogen mixed with 25 vol% DME achieved approximately a 30% improvement in fuel economy compared with HCCI of pure DME and spark-ignited lean-burn combustion of pure hydrogen under almost zero NOx emissions and low hydrocarbon (HC) emissions. This is attributed to control of the combustion process to attain the optimum onset of combustion and to a reduction of cooling losses.

Hydrogen spark-ignition (SI) engines based on direct-injection (DI) promise significant advantages in terms of thermal efficiency and power output, as well as a means of overcoming problems related to knocking, backfiring, and pre-ignition. In a DI hydrogen engine, the fuel/air mixture is formed by injecting a jet of hydrogen into the air inside the combustion chamber. An Ar-ion laser beam was used as a light source to visualize the hydrogen jet in a constant-volume chamber. This allowed us to study the structure of the jet in addition to other physical processes resulting from hydrogen gas injection. Combustion experiments were conducted in a single-cylinder SI optical research engine equipped with a DI system to detect the early kernel growth assisted by the spark, as well as flame propagation. Various equivalence ratios and fuel injection timings were analyzed to identify the effects on combustion.

Hydrogen is expected to be one of the most prominent fuels in the near future for solving greenhouse problem, protecting environment and saving petroleum. In this study, a dual fuel engine of hydrogen and diesel oil was investigated. Hydrogen was inducted in a intake port with air and diesel oil was injected into the cylinder. The injection timing was changed over extremely wide range. When the injection timing of diesel fuel into the cylinder is advanced, the diesel oil is well mixed with hydrogen-air mixture and the initial combustion becomes mild. NOx emissions decrease because of lean premixed combustion without the region of high temperature of burned gas. When hydrogen is mixed with inlet air, emissions of HC, CO and CO2 decrease without exhausting smoke while brake thermal efficiency is slightly smaller than that in ordinary diesel combustion.

The purpose of this study was to characterize the air/fuel ratio (AFR) of turbulent premixed flames in a spark-ignition (SI) engine. We developed a spark plug sensor with an optical fiber to detect the chemiluminescence spectra, specifically the intensity of the spectral lines related to OH*, CH*, and C2* free radicals. The sensor was composed of a sapphire window and optical fiber and is applicable to automobile SI engines. Measurements of the chemiluminescence intensity from OH*, CH*, and C2* radicals were obtained in turbulent premixed flames with a propane-air mixture for different AFRs in a compression-expansion machine (CEM). The performance of the spark plug sensor was compared with a Cassegrain reflector using an intensified charge-coupled device. The results showed good agreement with measurements obtained using the Cassegrain reflector. The spark plug sensor was shown to be useful for measuring chemiluminescence of turbulent premixed flames in an SI engine.

This study measured the fuel concentration near a spark plug using a laser infrared absorption method. An IR spark plug sensor with a double-pass measurement length was developed. A He-Ne laser with a wavelength of 3.392 μm, which coincides with the absorption line of hydrocarbons, was used as the light source. In order to confirm the measurement accuracy, the concentrations of a methane-air mixture were measured in a compression-expansion engine. Then, the IR spark plug sensor was used for measurements in a 4-stroke spark-ignition engine fuelled with isooctane. The air/fuel ratio measured using this system clearly agreed with the mean air/fuel ratio.

This paper describes the development and application of a spark plug sensor using a 3.392 μm infrared absorption technique to quantify the instantaneous gasoline concentration near the spark plug. We developed an in situ laser infrared absorption method using a spark plug sensor and a 3.392 μm He-Ne laser as the light source; this wavelength coincides with the absorption line of hydrocarbons. First, we established a database of the molar absorption coefficients of premium gasoline at different pressures and temperatures, and determined that the coefficient decreased with increasing pressure above atmospheric pressure. We then demonstrated a procedure for measuring the gasoline concentration accurately using the infrared absorption technique. The history of the molar absorption coefficient of premium gasoline during the experiment was obtained from the established database using measured in-cylinder pressures and temperatures estimated by taking the residual gas into consideration.