Refine Your Search

Date

Date

Topic

Topic

Materials Manufacturing processes Humidity Steel AGE-3 Aircraft Ground Support Equipment Committee

Search Results

Viewing 1 to 20 of 48
123Next >Last >>
Sort by title
Standard

400 Hz CONNECTION AIRCRAFT ELECTRICAL MAINTENANCE PROCEDURES
1994-12-01
HISTORICAL
AIR4365
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
Standard

400 Hz Connection Aircraft Electrical Maintenance Procedures
2008-03-28
HISTORICAL
AIR4365A
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
Standard

AIRCRAFT ENVIRONMENTAL FACTORS FOR DESIGN CONSIDERATION
2002-12-16
CURRENT
AIR1309
This AIR is presented in two parts - the first part, to alert the engineer with respect to the environmental factors which he might have to consider - the second part, as tabular data and figures to which he can refer with respect to a specific geographical location.
Standard

AIRCRAFT GROUND AIR CONDITIONING SERVICE CONNECTION
2005-07-11
HISTORICAL
AS4262A
This SAE Aerospace Standard (AS) defines interface configurations for the ground air conditioning service connection on commercial transport aircraft. In addition, it defines the clearances required to accommodate the connection of ground air conditioning hose couplings. Two types of service connections are included. The Type A connection (Figure 1) is a slotted ring with integral locking pads and is comparable to the MS33562 connection. The Type B connection (Figure 2) is a flanged tube with external locking lugs (Figure 3). The Type B connection has the same interface dimensional requirements as the Type A connection.
Standard

AIRCRAFT GROUND AIR CONDITIONING SERVICE CONNECTION
1991-02-12
HISTORICAL
AS4262
This SAE Aerospace Standard (AS) defines interface configurations for the ground air conditioning service connection on commercial transport aircraft. In addition, it defines the clearances required to accommodate the connection of ground air conditioning hose couplings. Two types of service connections are included. The Type A connection (Figure 1) is a slotted ring with integral locking pads and is comparable to the MS33562 connection. The Type B connection (Figure 2) is a flanged tube with external locking lugs (Figure 3). The Type B connection has the same interface dimensional requirements as the Type A connection.
Standard

AIRCRAFT MAINTENANCE JACKS - GENERAL REQUIREMENTS
1994-07-01
HISTORICAL
AS4775
This document covers the general requirements for hydraulic jacks as used on commercial aircraft. It can be applied to tripod, unipod, and axle jacks which may be used on open ramp areas as well as in the aircraft hanger.
Standard

Aircraft Maintenance Jacks - General Requirements
2011-01-14
HISTORICAL
AS4775A
This document covers the general requirements for hydraulic aircraft jacks. It can be applied to tripod, unipod, and axle jacks that may be used on open ramp areas as well as in the aircraft hanger. Throughout this Aerospace Standard, the minimum essential criteria are identified by the key word “shall”. Recommended criteria are identified by use of the key word “should”. Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternate methods to provide an equivalent level of safety. The term “vertical load” throughout this Aerospace Standard is defined as the force imposed on the aircraft jack at the airframe jack point.
Standard

Aircraft Markings for Ground Support Equipment Alignment
2020-04-24
CURRENT
AS6896
The purpose of this document is to provide a standard for aircraft fuselage markings located at the doors used for ground servicing operations. These markings can be used by all GSE that will dock at the aircraft. These markings may be used for one or several phases of the GSE positioning relative to the aircraft process: GSE alignment during approach, GSE final docking, and GSE auto leveling. It is not the purpose of this standard to describe the different technologies, cameras, or other equipment that can be mounted on GSE to utilize these markings. The aircraft that may use these markings will have a fuselage diameter of 3 m or more.
Standard

Aural Protector, Sound
1999-05-01
HISTORICAL
AS23899
This specification covers the design and performance requirements for one type of sound aural protector.
Standard

Aural Protector, Sound
2012-01-24
CURRENT
AS23899A
This specification covers the design and performance requirements for one type of sound aural protector.
Standard

CHARGER FOR BATTERY POWERED GROUND SUPPORT EQUIPMENT
1991-04-01
HISTORICAL
ARP1816A
This recommended practice describes an industrial battery charger, solid state type, hereafter called charger, for use in charging lead acid batteries in ground support equipment.
Standard

CHARGER FOR BATTERY POWERED GROUND SUPPORT EQUIPMENT
1984-09-01
HISTORICAL
ARP1816
This recommended practice describes an industrial battery charger, solid state type, hereafter called charger, for use in charging lead acid batteries in ground support equipment.
123Next >Last >>
X