Search Results

Engines and fuels for transport as well as off-road applications are facing a double challenge: bring local pollution to the level requested by the most stringent city air quality standard reduce CO2 emission in order to minimize the global warming risk. These goals stimulate new developments both of conventional and alternative engines and fuels technologies. New combustion processes known as Controlled Auto-Ignition (CAI™) for gasoline engine and Homogeneous Charge Compression Ignition (HCCI) for Diesel engine are the subject of extensive research world wide and particularly at IFP for various applications such as passenger cars, heavy-duty trucks and buses as well as small engines. Because of the thermo-chemistry of the charge, the thermal NOx formation and the soot production are in principle much lower than in flames typical of conventional engines.

Controlled Auto-Ignition (CAI) also known as Homogeneous Charge Compression Ignition (HCCI) is increasingly seen as a very effective way of lowering both fuel consumption and emissions. Hence, it is regarded as one of the best ways to meet stringent future emissions legislation. It has however, still many problems to overcome, such as limited operating range. This combustion concept was achieved in a production type, 4-cylinder gasoline engine, in two separated tests: naturally aspirated and turbocharged. Very few modifications to the original engine were needed. These consisted basically of a new set of camshafts for the naturally aspirated test and new camshafts plus turbocharger for the test with forced induction. After previous experiments with naturally aspirated CAI operation, it was decided to investigate the capability of turbocharging for extended CAI load and speed range.

A new concept for high efficiency two-stroke cycle spark-ignition engines has been developed. The installation of the IFP-developed pneumatic fuel injection process in a two-stroke engine allows the introduction of the fuel separately from the scavenging air, in order to minimize fuel shortcircuiting. The process does not require an external air pump since the compressed air used to atomize the fuel is supplied at no expense by the crankcase. The premixed charge is delivered directly into the cylinder with a high spray quality, its stratification for the optimization of combustion is controlled by a valve. This process, therefore, provides the advantages of the direct injection but uses commercially available gasoline injectors. A single-cylinder engine has been developed first to verify the potential of the process.

The possibility to vary compression ratio offers a new degree of freedom that may enable so far not exploited benefits for the combustion process especially for highly boosted spark ignited engines. Numerous approaches to enable a variable compression ratio (VCR) have been tried and tested in the past. Nevertheless, none of these systems reached series production because of several reasons, ranging from too much complexity and moveable parts to deep modification required on existing engine architectures and manufacturing lines. Instead, the approach of a variable length conrod (VCR conrod) could be the solution for integration in almost any type of engine with minor modifications. It is then considered by several OEMs as a promising candidate for midterm series production. This paper shows, firstly, a discussion of the benefits of a variable compression ratio system.

Renewable fuels have received more attention in the last few decades since the fuel demand is constantly increasing. In this scenario, fuels from vegetable oils are emerging as an interesting alternative. In this study, biodiesel produced from used cooking oil was studied. Several concentrations of biofuel were tested to evaluate their performance and combustion characteristics i.e. 7% (B07), 17% (B17), 27% (B27), 52% (B52), 77% (B77) and 100% by volume of Biodiesel (B100) on conventional diesel. Tests were conducted in a single cylinder four-stroke compression ignition engine. A 1-D computational model was built and compared to experimental results. The biodiesel concentration in the blends had influence on engine performance by increasing fuel consumption due to its reduced lower heating value. In addition, larger fractions of biodiesel on conventional diesel presented higher peak of heat release.

The implementation of the IFP developed Compressed Air Assisted Fuel Injection Process (named IAPAC) in a two-stroke engine allows the introduction of the fuel separately from the scavenging air, which in consequence minimizes fuel short-circuiting. The inherent mechanical principle of the IAPAC process which uses the crankcase compressed air to finely atomize the fuel, provides the advantages of direct injection but in addition uses conventional low pressure automotive type injection technology with commercially available gasoline injectors. In earlier work we showed an example of the application of this fuel injection technology to a PIAGGIO single cylinder 125 cc scooter two-stroke engine. In this paper, an update of the results obtained with this new engine is presented and confirms the ultra-low emissions capability for two-wheeler application.

The aim of this paper is to show that the gains, technical and/or economical, from the use of ethanol as fuel in agricultural aviation may be even greater if the aircraft engine is specially designed for that purpose. A specific design is also necessary if it is intended to achieve a truly "green" engine, neutral regarding carbon emissions. Using available technologies, computational tools, development methods and project management methods (Reference Model for Agricultural Machinery Development Process (RM-AMDP), the engine can be fully developed to be used specifically as an agricultural aircraft propellant operating with ethanol. In Brazil, the current fleet of agricultural airplanes has around 1500 aircrafts and almost all operating with AvGas (Aviation Gasoline). There is already in Brazil a "green" airplane, manufactured by Neiva, a subsidiary of the aircraft manufacturer Embraer. This model uses a conversion kit on the original engine to use ethanol as fuel.

New combustion processes known as Controlled Auto-Ignition (CAI™) for gasoline engine and Homogeneous Charge Compression Ignition (HCCI) for Diesel engine are the subject of extensive research worldwide and particularly at IFP. Because of the thermo-chemistry conditions of the charge, the thermal NOx formation is in principle much less than with flames typical of the conventional engines. Indeed, these new combustion processes bring NOx to virtually zero “1 digit” ppm while maintaining a very high thermodynamic efficiency of the combustion. One major issue in the development of CAI combustion for gasoline engines remains the limited engine speed and load range that can be operated in CAI combustion mode, while maintaining near zero NOx and acceptable noise emissions.

The relative contribution of two wheelers to local atmosphere pollution is increasing more and more due to ultra low emissions regulation applied to other vehicle as cars. In 1999, the first European emissions regulations for 50cc mopeds and scooters appeared (Euro I) and will also become more and more severe by the time. Euro II (2002) level will correspond to the next step. IFP has developed a simplified Direct Injection technology, named SCIP™, derived from the well known IAPAC® technology without the need of additional camshaft. This technology has been integrated with the MC500 Engine Management System developed by SAGEM for the growing 2-wheelers application. The final simple and cheap product is therefore well adapted to small displacement 2-stroke engines as 50cc engine for 2-wheelers application. This paper presents the development of a 50 cc scooter engine using SCIP™ technology and the calibration of the MC500 System to achieve Euro II regulation.

Controlled Auto-Ignition (CAI), also known as HCCI (Homogeneous Charge Compression Ignition), is increasingly seen as a very effective way of lowering both fuel consumption and emissions from gasoline engines. Therefore, it's seen as one of the best ways to meet future engine emissions and CO2 legislations. This combustion concept was achieved in a Ford production, port-injected, 4 cylinder gasoline engine. The only major modification to the original engine was the replacement of the original camshafts by a new set of custom made ones. The CAI operation was accomplished by means of using residual gas trapping made possible by the use of VCT (variable cam timing) on both intake and exhaust camshafts. When running on CAI, the engine was able to achieve CAI combustion with in a load range of 0.5 to 4.5 BMEP, and a speed range of 1000 to 3500 rpm. In addition, spark assisted CAI operation was employed to extend the operational range of low NOx and low pumping loss at part-load conditions.

The IAPAC® Direct fuel Injection (DI) system, developed by IFP, has already well proven its capability to reduce pollutants emissions and fuel consumption of 2-stroke engines for both 2-wheeler and marine outboard application. This crankcase Compressed Air Assisted Fuel Injection process allowing the introduction of the fuel separately from the scavenging air, minimizes the fuel short-circuiting and has shown its potential on various prototype demonstrators. This paper presents the development and pre-industrialization work performed to apply this concept to an SELVA Marine 2-cylinder 50 HP outboard 2-stroke engine. A standard carbureted engine has been converted to a IAPAC® prototype engine by mainly modifying the cylinder head. Then, this prototype engine has been calibrated, tested and optimized on the dyno test bench to comply with future emissions regulation while keeping similar power output than the reference carbureted engine.

Ethanol with high levels of hydration is a low cost fuel that offers the potential to replace fossil fuels and contribute to lower carbon dioxide (CO2) emissions. However, it presents several ignition challenges depending on the hydration level and ambient temperature. Advanced combustion concepts such as homogeneous charge compression ignition (HCCI) have shown to be very tolerant to the water content in the fuel due to their non-flame propagating nature. Moreover, HCCI tends to increase engine efficiency while reducing oxides of nitrogen (NOx) emissions. In this sense, the present research demonstrates the operation of a 3-cylinder power generator engine in which two cylinders operate on conventional diesel combustion (CDC) and provide recycled exhaust gas (EGR) for the last cylinder running on wet ethanol HCCI combustion. At low engine loads the cylinders operating on CDC provide high oxygen content EGR for the dedicated HCCI cylinder.

Low cost ethanol with high levels of hydrations is a fuel that can be easily produced and that offers the potential to replace fossil fuels and contribute to reduce greenhouse gas emissions. However, it shows several ignition challenges depending on the hydration level, ambient temperature compression ratio and other engine-specific aspects. Advanced combustion concepts such as homogeneous charge compression ignition (HCCI) have shown to be very tolerant to the water content in the fuel due to their non-flame propagating nature. Moreover, HCCI tends to increase engine efficiency while reducing oxides of nitrogen (NOx) emissions. In this sense, the present research demonstrates the operation of a 3-cylinder power generator engine in which two cylinders operate on conventional diesel combustion (CDC) and provide recycled exhaust gas (EGR) for the last cylinder running on wet ethanol HCCI combustion.

The implementation of the IFP-developped Compressed Air Assisted Fuel Injection process (named IAPAC) on a two-stroke engine allows the introduction of the fuel separately from the scavenging air in order to minimize fuel short-circuiting. The IAPAC process does not require an external air pump since the compressed air used to atomize the fuel is supplied, at no expense, by the crankcase. The premixed charge is delivered directly into the cylinder with a high spray quality and its stratification, for optimized combustion, is controlled by a valve. This process, therefore, provides the advantages of the direct injection but uses conventional low-pressure automotive type injection technology with commercially available gasoline injectors. In earlier work, we showed how the qualities of light weight, compactness, high specific power, high efficiency and low emissions make this concept particularly well-adapted for future automotive applications.

The implementation of the IFP-developped Compressed Air Assisted Fuel Injection process (named IAPAC) on a two-stroke engine allows the introduction of the fuel separately from the scavenging air in order to minimize fuel short-circuiting. The IAPAC process does not require an external air pump since the compressed air used to atomize the fuel is supplied, at no expense, by the crankcase. The premixed charge is delivered directly into the cylinder with a high spray quality and its stratification, for optimized combustion, is controlled by a valve. This process, therefore, provides the advantages of the direct injection but uses conventional low-pressure automotive type injection technology with commercially available gasoline injectors. In earlier work we showed how the qualities of light weight, compactness, high specific power, high efficiency and low emissions make this concept particularly well-adapted for future automotive applications.

The purpose of the 4-SPACE (4-Stroke Powered gasoline Auto-ignition Controlled combustion Engine) industrial research project is to research and develop an innovative controlled auto-ignition combustion process for lean burn automotive gasoline 4-stroke engines application. The engine concepts to be developed could have the potential to replace the existing stoichiometric / 3-way catalyst automotive spark ignition 4-stroke engines by offering the potential to meet the most stringent EURO 4 emissions limits in the year 2005 without requiring DeNOx catalyst technology. A reduction of fuel consumption and therefore of corresponding CO2 emissions of 15 to 20% in average urban conditions of use, is expected for the « 4-SPACE » lean burn 4-stroke engine with additional reduction of CO emissions.

The prediction of ignition delay times is very useful during the development phase of internal combustion engines. When it comes to biofuels such as ethanol and its blends with gasoline, its importance is enhanced, especially when it comes to flex-fuel engines and the need to address current and future emissions legislations and efficiency goals. The ignition delay time measured as the angular difference between the spark discharge time, as commanded by the ECU and a relevant fraction of fuel mass burned (usually, 2, 5 or 10%). Experimental tests were performed on a downsized state-of-the-art internal combustion engine. Engine speed of 2500 rpm, with load of 6 and 13 bar IMEP were set for investigation. Stoichiometric operation and MBT or knock-limited spark timings were used, while valve overlap was varied, in order to address the effects of scavenging and residuals on ignition delay times.

This study evaluates the performance of an ethanol fueled spark ignited engine running with high levels of hydration. Ethanol is a renewable fuel and has been considered a promising alternative to counteract global warming and to reduce pollutant emissions. Its use is well established in ICE as the main fuel or blended with gasoline. However, due to its lower calorific value, it shows increased fuel consumption when compared to gasoline, rendering its use sometimes less attractive. The energy demand to produce ethanol, especially at the distillation phase, increases exponentially as the concentration of ethanol-in-water goes from 80% onwards. Thus, mixtures with less than 80% of ethanol-in-water would reduce the energy consumption during production, yielding a less expensive fuel. In previous studies, to evaluate the feasibility of wet ethanol as a fuel for spark-ignited engines, results have shown that it was possible to use mixtures of up to 40% of water-in-ethanol.

The main purpose of this paper will be to investigate if a small snowmobile gasoline Direct Injected (DI) two-stroke engine has the potential to be adapted for two other types of applications: as a range extender (REX) for electric vehicles and for a motorcycle application. For the REX application, the main requested specifications (NVH, lightweight, compactness, minimum production cost and easy maintenance), correspond well to the main features of DI 2-stroke engines. The potential of a modified production engine operating in part load ultra-low NOx Controlled Auto Ignition (CAI) to meet the Euro 6 emissions standards on the NEDC cycle has already been demonstrated in a previous paper. In the first part of this new paper, we will investigate which solutions can be used to maintain this potential with even stricter legislations based on Euro 6d, WLTP cycle and Real Driving Emissions (RDE).

The purpose of the European « SPACE LIGHT » (Whole SPACE combustion for LIGHT duty diesel vehicles) 3-year project launched in 2001 is to research and develop an innovative Homogeneous internal mixture Charged Compression Ignition (HCCI) for passenger cars diesel engine where the combustion process can take place simultaneously in the whole SPACE of the combustion chamber while providing almost no NOx and particulates emissions. This paper presents the whole project with the main R&D tasks necessary to comply with the industrial and technical objectives of the project. The research approach adopted is briefly described. It is then followed by a detailed description of the most recent progress achieved during the tasks recently undertaken. The methodology adopted starts from the research study of the in-cylinder combustion specifications necessary to achieve HCCI combustion from experimental single cylinder engines testing in premixed charged conditions.