Search Results

Controlled Auto Ignition (CAI), also known as Homogeneous Charge Compression Ignition (HCCI), is one of the most promising combustion technologies to reduce the fuel consumption and NOx emissions. Currently, CAI combustion is constrained at part load operation conditions because of misfire at low load and knocking combustion at high load, and the lack of effective means to control the combustion process. Extending its operating range including high load boundary towards full load and low load boundary towards idle in order to allow the CAI engine to meet the demand of whole vehicle driving cycles, has become one of the key issues facing the industrialisation of CAI/HCCI technology. Furthermore, this combustion mode should be compatible with different fuels, and can switch back to conventional spark ignition operation when necessary. In this paper, the CAI operation is demonstrated on a 2-stroke gasoline direct injection (GDI) engine equipped with a poppet valve train.

Direct injection gasoline engines have the potential for improved fuel economy through principally the engine down-sizing, stratified charge combustion, and Controlled Auto Ignition (CAI). However, due to the limited time available for complete fuel evaporation and the mixing of fuel and air mixture, locally fuel rich mixture or even liquid fuel can be present during the combustion process of a direct injection gasoline engine. This can result in significant increase in UHC, CO and Particulate Matter (PM) emissions from direct injection gasoline engines which are of major concerns because of the environmental and health implications. In order to investigate and develop a more efficient DI gasoline engine, a camless single cylinder DI gasoline engine has been developed. Fully flexible electro-hydraulically controlled valve train was used to achieve spark ignition (SI) and Controlled Autoignition (CAI) combustion in both 4-stroke and 2-stroke cycles.

Controlled Auto Ignition (CAI), also known as Homogeneous Charge Compression Ignition (HCCI), is one of the most promising combustion technologies to reduce the fuel consumption and NOx emissions. Most research on CAI/HCCI combustion operations have been carried out in 4-stroke gasoline engines, despite it was originally employed to improve the part-load combustion and emission in the two-stroke gasoline engine. However, conventional ported two-stroke engines suffer from durability and high emissions. In order to take advantage of the high power density of the two-stroke cycle operation and avoid the difficulties of the ported engine, systematic research and development works have been carried out on the two-stroke cycle operation in a 4-valves gasoline engine. CAI combustion was achieved over a large range of operating conditions when the relative air/fuel ratio (lambda) was kept at one as measured by an exhaust lambda sensor.

To ensure overall optimisation of heavy duty engine performance (with the respect of NOx&PM future European and US emissions standards), the use of a high efficiency NOx after-treatment system such as a NOx trap appears to be necessary. But running in rich conditions, even for a short time, leads to a large increase of particulate emissions so that a particulate filter is required. A first investigation with a NOx-trap only has been carried out to evaluate and optimise the storage, destorage and reduction phases from the NOx conversion efficiency and fuel penalty trade-off. The equivalence ratio level, the fuel penalty and the temperature level of the NOx-trap have been shown as a key parameter. Respective DPF and LNA locations have been studied. The configuration with the NOx-trap upstream provides the best NOx / fuel penalty trade-off since it allows NOx slip reduction and does not disturb the rich pulses.

This paper presents the detailed characterization of particulate emissions from a NADI™ dual mode engine (HCCI at low load and conventional combustion at high load). Morphology, composition and chemical reactivity of the particulate matter generated on an engine running in HCCI mode have been specified and compared to the conventional mode reference. Results showed that HCCI combustion formed particles with a higher volatile organic fraction due to the relatively high level of HC generated by this kind of combustion. Advanced soot characterization emphasized that HCCI soot is oxidized at a slower reaction rate than conventional soot, but with a lower temperature. This last characteristic could partially compensate the poor continuous regeneration effect due to low NO2 emission levels observed in HCCI combustion. Microscopic observation and particle sizing did not show significant differences between HCCI and conventional soot.

An accurate prediction of residual burned gas within the combustion chamber is important to quantify for development of modern engines, especially so for those with internally recycled burned gases and HCCI operations. A wall-guided GDI engine has been fitted with an in-cylinder sampling probe attached to a fast response NDIR analyser to measure in-situ the cycle-by-cycle trapped residual gas. The results have been compared with a model which predicts the trapped residual gas fraction based on heat release rate calculated from the cylinder pressure data and other factors. The inlet and exhaust valve timings were varied to produce a range of Residual Gas Fraction (RGF) conditions and the results were compared between the actual measured CO2 values and those predicted by the model, which shows that the RGF value derived from the exhaust gas temperature and pressure measurement at EVC is consistently overestimated by 5% over those based on the CO2 concentrations.

Internal combustion engines are subjected to part-load operation more than in full load during a typical vehicle driving cycle. The problem with the Spark Ignition (SI) engine is its inherent low part-load efficiency. This problem arises due to the pumping loses that occur when the throttle closes or partially opens. One way of decreasing the pumping losses is to operate the engine lean or by adding residual gases. It is not possible to operate the engine unthrottled at very low loads due to misfire. However, the load can also be controlled by changing the intake valve closing timing - either early or late intake valve closing. Both strategies reduce the pumping loses and hence increase the efficiency. However the early intake valve closure (EIVC) can be used as mode transition from SI to CAI combustion.

In recent years, in order to develop more efficient and cleaner gasoline engines, a number of new engine operating strategies have been proposed and many have been studied on different engines but there is a lack of comparison between various operating strategies and alternative fuels at different SI modes. In this research, a single cylinder direct injection gasoline engine equipped with an electro-hydraulic valve train system has been commissioned and used to study and compare different engine operation modes. In this work, the fuel consumption, gaseous and particulate emissions of gasoline and its mixture with ethanol (E15 and E85) were measured and analysed when the engine was operated at the same load but with different load control methods by an intake throttle, reduced intake valve duration, and positive overlap.

This work studies the potential of ethanol-Biodiesel-Diesel fuel blends in both conventional Diesel and HCCI combustion modes. First, ethanol based fuels were tested on a modern commercial multi-cylinder DI diesel engine. The aim of this phase was to assess how such fuels affect Diesel engine performances and emissions. These results indicate that low levels of PM and NOx emissions, with a contained fuel consumption penalty and with an acceptable noise level, are achievable when the Diesel-ethanol blends are used in combination with an optimized combustion control. Moreover, experiments with ethanol based blends were performed using a single cylinder engine, running under both early injection HCCI and Diesel combustion modes. Compared to a conventional fuel, these blends allow increasing the HCCI operating range and also lead to higher maximum power output in conventional Diesel combustion.

Facing more and more stringent regulations, new solutions are developed to decrease pollutant emissions. One of them have shown promising and relevant results. It consists of the use of ethanol as a blending component for diesel fuel Nevertheless, the addition of ethanol to Diesel fuel affects some key properties such as the flash point. Consequently, Diesel blends containing ethanol become highly flammable at a temperature around ambient temperature. This study proposes to improve the formulation of ethanol based diesel fuel in order to avoid flash point drawbacks. First, a focus on physical and chemical properties is done for ethanol based diesel fuels with and without flash point improvement. Second, blends are tested on a passenger car diesel engine, under a wide operating range conditions from low load low speed up to maximum power. The main advantage of the ethanol based fuels generate low smoke level, that allows using higher EGR rate, thus leading to an important NOx decrease.

The relative contribution of two wheelers to local atmosphere pollution is increasing more and more due to ultra low emissions regulation applied to other vehicle as cars. In 1999, the first European emissions regulations for 50cc mopeds and scooters appeared (Euro I) and will also become more and more severe by the time. Euro II (2002) level will correspond to the next step. IFP has developed a simplified Direct Injection technology, named SCIP™, derived from the well known IAPAC® technology without the need of additional camshaft. This technology has been integrated with the MC500 Engine Management System developed by SAGEM for the growing 2-wheelers application. The final simple and cheap product is therefore well adapted to small displacement 2-stroke engines as 50cc engine for 2-wheelers application. This paper presents the development of a 50 cc scooter engine using SCIP™ technology and the calibration of the MC500 System to achieve Euro II regulation.

Controlled Auto-Ignition (CAI), also known as Homogeneous Charge Compression Ignition (HCCI), can improve the fuel economy of gasoline engines and simultaneously achieve ultra-low NOx emissions. However, the difficulty in combustion phasing control and violent combustion at high loads limit the commercial application of CAI combustion. To overcome these problems, stratified mixture, which is rich around the central spark plug and lean around the cylinder wall, is formed through port fuel injection and direct injection of gasoline. In this condition, rich mixture is consumed by flame propagation after spark ignition, while the unburned lean mixture auto-ignites due to the increased in-cylinder temperature during flame propagation, i.e., stratified flame ignited (SFI) hybrid combustion.

The IAPAC® Direct fuel Injection (DI) system, developed by IFP, has already well proven its capability to reduce pollutants emissions and fuel consumption of 2-stroke engines for both 2-wheeler and marine outboard application. This crankcase Compressed Air Assisted Fuel Injection process allowing the introduction of the fuel separately from the scavenging air, minimizes the fuel short-circuiting and has shown its potential on various prototype demonstrators. This paper presents the development and pre-industrialization work performed to apply this concept to an SELVA Marine 2-cylinder 50 HP outboard 2-stroke engine. A standard carbureted engine has been converted to a IAPAC® prototype engine by mainly modifying the cylinder head. Then, this prototype engine has been calibrated, tested and optimized on the dyno test bench to comply with future emissions regulation while keeping similar power output than the reference carbureted engine.

Diesel urban buses and refuse trucks are part of the particulate emissions sources that affect city air quality. In order to reduce particulate pollutant emissions, a development program has been carried out based on a Euro 4 engine with a DPF technology. Currently, for Euro 4 compliance, SCR is the favoured technology. To avoid a completely new development, the Exoclean™ DPF system was located after the SCR. Catalyst. The severe operating conditions and the location of the DPF necessitated the development of an active system based on the association of a DPF and a Fuel-Borne Catalyst. A Renault Trucks MD9 engine was used. This work was funded by ADEME (French Agency for Environment and Energy Management). Due to severe stop and go duty cycles and the interest to fit the DPF downstream of the SCR, this study shows the benefit of using an active DPF with an FBC to ensure full regeneration even at low temperatures.

The purpose of the 4-SPACE (4-Stroke Powered gasoline Auto-ignition Controlled combustion Engine) industrial research project is to research and develop an innovative controlled auto-ignition combustion process for lean burn automotive gasoline 4-stroke engines application. The engine concepts to be developed could have the potential to replace the existing stoichiometric / 3-way catalyst automotive spark ignition 4-stroke engines by offering the potential to meet the most stringent EURO 4 emissions limits in the year 2005 without requiring DeNOx catalyst technology. A reduction of fuel consumption and therefore of corresponding CO2 emissions of 15 to 20% in average urban conditions of use, is expected for the « 4-SPACE » lean burn 4-stroke engine with additional reduction of CO emissions.

Controlled Auto Ignition (CAI), also known as Homogeneous Charge Compression Ignition (HCCI), is one of the most promising combustion technologies to reduce the fuel consumption and NOx emissions. In order to take advantage of the inherent ability to retain a large and varied amount of residual at part-load condition and its potential to achieve extreme engine downsizing of a poppet valve engine running in the 2-stroke cycle, a single cylinder 4-valves camless direct injection gasoline engine has been developed and employed to investigate the CAI combustion process in the 2-stroke cycle mode. The CAI combustion is initiated by trapped residual gases from the adjustable scavenging process enabled by the variable intake and exhaust valve timings. In addition, the boosted intake air is used to provide the in-cylinder air/fuel mixture for maximum combustion efficiency.

With the emergence of stringent emissions standards and needs for fuel diversification, many countries are considering a massive use of natural gas for transportation. In this context, dual fuel diesel-CNG combustion is considered as a promising solution for highly efficient internal combustion engines. This concept offers the possibility to combine a diesel pilot injection as a high energy combustion initiation event, with an indirect injection of methane as main energy source. Low CO2 emissions can be reached thanks to the use of a conventional compression ignition engine with high compression ratio, and thanks to methane's high knocking resistance and low carbon content. Another benefit of dual fuel operation with high diesel substitution rates is the drastic reduction of PM emissions since methane is a very stable molecule containing no soot precursor.

Diversifying energy resources and reducing greenhouse gas emissions are key priorities in the forthcoming years for the automotive industry. Currently, among the different solutions, sustainable biofuels are considered as one of the most attractive answer to these issues. This paper deals with the vehicle application of an innovative diesel fuel formulation using Ethanol to tackle these future challenges. The main goal is to better understand the impact of using biofuel blends on engine behavior, reliability and pollutants emissions. This alternative oxygenated fuel reduces dramatically particulate matter (PM) emissions; this paves the way to improve the NOx/PM/CO₂ trade-off. Another major interest is to avoid adding a particulate filter in the exhaust line and to avoid modifying powertrain and vehicle hardware and therefore to minimize the overall cost to fulfill upcoming emission regulations.

Current progress in the development of diesel engines substantially contributes to the reduction of NOx and Particulate Matter (PM) emissions but will not succeed to eliminate the application of Diesel Particulate Filters (DPFs) in the future. In the past we have introduced a Multi-Functional Reactor (MFR) prototype, suitable for the abatement of the gaseous and PM emissions of the Low Temperature Combustion (LTC) engine operation. In this work the performance of MFR prototypes under both conventional and advanced combustion engine operating conditions is presented. The effect of the MFR on the fuel penalty associated to the filter regeneration is assessed via simulation. Special focus is placed on presenting the performance assessment in combination with the existing differences in the morphology and reactivity of the soot particles between the different modes of diesel engine operation (conventional and advanced). The effect of aging on the MFR performance is also presented.

To comply with ever more stringent emission limits, engineers are studying and optimising gasoline engine start-up and warm-up phases. Secondary air injection (SAI) represents one option to reduce emissions by post-oxidizing products of a rich combustion like HC, CO and H2. With this approach, the faster catalytic converter light-off allowed by the increase in exhaust temperature leads to a significant HC emissions reduction. All the mechanisms involved in post oxidation downstream of the exhaust valve are not well-known. In order to achieve substantial improvements, various SAI strategies were studied with a conventional PFI gasoline engine. Tests have been carried out both on steady-state running conditions and on transient warm-up phases at engine test bench. Various specific experimental devices and methodologies were developed. For example, the use of fast HC and temperature measurements is coupled with exhaust gas flow rate modeled with system simulation.