Search Results

The oxidations of Crapped diesel soots containing catalytic metals such as Ca, Ba, Fe, or Ni were characterized through thermogravimetric analysis with a thermobalance. Soot particles were generated by a single cylinder IDI diesel engine with metallic fuel additives. A two-stage oxidation process was observed with the metalcontalning soots. It was found that the first stage of oxidation is catalytically promoted by metal additives resulting in an enhanced reaction rate and a reduced activation energy. Soot reduction in the rapid first stage increases with increases in metal content. Soots containing Ba and Ca are oxidized most rapidly due to the larger reduction during the first stage. The second stage of oxidation is also slightly promoted by metal addition. The ignition temperature of the collected soot is substantially reduced by the metal additives.

Experiments on a large number of soluble fuel additives were systematically conducted for diesel soot reduction. It was found that Ca and Ba were the most effective soot suppressors. The main determinants of soot reduction were: the metal mol-content of the fuel, the excess air factor, and the gas turbulence in the combustion chamber. The soot reduction ratio was expressed by an exponential function of the metal mol-content in the fuel, depending on the metal but independent of the metal compound. A rise in excess air factor or gas turbulence increased the value of a coefficient in the function, resulting in larger reductions in soot with the fuel additives. High-speed soot sampling from the cylinder showed that with the metal additive, the soot concentration in the combustion chamber was substantially reduced during the whole period of combustion. It is thought that the additive acts as a catalyst not only to improve soot oxidation but also to suppress soot formation.

Light naphtha, which exhibits two-stage ignition, was induced from the intake manifold for ignition enhancement and a low ignitability fuel or water, which does not exhibit low temperature oxidation, was directly injected early in the compression stroke for ignition suppression in an HCCI engine. Their quantitative balance was flexibly controlled to optimize ignition timing according to operating condition. Ultra-low NOx and smokeless combustion without knocking or misfiring was realized over a wide operating range. Alcohols inhibit low temperature oxidation more strongly than other oxygenated or unoxygenated hydrocarbons, water, and hydrogen. Chemical kinetic modeling for methanol showed a reduction of OH radical concentration before the onset of low temperature oxidation, and this may be the main mechanism by which alcohols inhibit low temperature oxidation.

Valve deposits in gasoline engines increase with time, absorbing fuel during acceleration and releasing fuel during deceleration. Valve deposits insulate the heat release from the cylinder and this phenomenon is the cause of bad fuel vaporization. In this way, the deposits greatly affect the driveability and exhaust emissions. Using a 3.OL MPI(Multipoint Injection) engine, we measured the quantity of fuel that deposits at the intake port, and the throttle response (using a wall-flow meter made by Nissan Motor Co.1), 2) to study the deposits effect on driveability and exhaust emissions at a low temperature. The deposits were formed on the intake valve surface (about 8.0 on the CRC deposit rating scale) through 200 hours of laboratory engine stand operation. At low temperature, C9 and C10 hydrocarbons tend to stick to the intake port surface and intake valve as “wall-flow”; this is one cause of bad driveability.

Smokeless and ultra low NOx combustion without knocking in a dual-fuel diesel engine with induced LPG as the main fuel was established with a uniquely developed piston cavity divided by a lip in the sidewall. A small quantity of diesel fuel was directly injected at early compression stroke into the lower part of the cavity as an ignition source for this confined area, and this suppressed explosively rapid combustion just after ignition and spark-knock like combustion at later stage. A combination of the divided cavity, EGR, and intake air throttling was effective to simultaneously eliminate knocking, and reduce THC and NOx significantly.

The chemical composition of marketed gasoline varies depending on the crude oil, refinery processes of oil refineries, and season. The combustion characteristics of HCCI engines are very sensitive to the fuel composition, and a fuel standard for HCCI is needed for HCCI vehicles to be commercially viable. In this paper, the effects of the structure of the fuel components on auto-ignition characteristics and HCCI engine performance were investigated. The engine employed in the experiments is a research, single cylinder HCCI engine with a compression ratio of 14.7. The intake manifold was equipped with a heater attachment allowing control of the intake air temperature up to 150 °C at 2000 rpm. Thirteen kinds of hydrocarbons, 4 kinds of paraffins, 3kinds of naphthenes, and 6 kinds of aromatics, were chosen for the investigation, and 20vol% of each of the pure hydrocarbons was blended with the 80 vol% of PFR50 fuel.

Diesel soot suppression effects of catalytic fuel additives for a range of fuels with different properties were investigated with calcium naphthenate. A single cylinder DI diesel engine and a thermobalance were used to determine the soot reduction and its mechanism for seven kinds of fuels. Experimental results showed that the catalytic effect of the fuel additive was different for the different fuels, and could be described by a parameter considering cetane number and kinematic viscosity. The fuel additives reduced soot more effectively for fuels with higher cetane number and lower kinematic viscosity. This result was explained by soot oxidation characteristics for the different fuels. Oxidation of soot with the metallic additive proceeds in two stages: stage I, a very rapid oxidation stage; and stage II, a following slow or ordinary oxidation stage.

To evaluate the relation between the intake air temperature (Tair-in), low temperature heat release (LTHR) and high temperature heat release (HTHR), a supercharged 4-cylinder engine with intake air heating, high compression pistons and a pressure transducer in each cylinder was introduced Eleven pure hydrocarbon components were blended into 23 different model fuels, labeled BASE MC01-MC11, and K01-K11. BASE is a mixture of equal proportion of each of the 11 pure hydrocarbons. The difference between MC series and K series fuels is in the amount of pure hydrocarbon added to the BASE: 6.5vol% for MC series fuels and 17.5vol% for K series fuels. Engine tests were performed with BASE and MC01-MC11 fuels at Tair-in=50°C (IMEP 530kPa), 80°C (IMEP 420kPa), and 100°C (IMEP 380kPa).