Search Results

The combined impacts of engine speed and fuel reactivity on energy-assisted compression-ignition (EACI) combustion using a commercial off-the-shelf (COTS) ceramic glow plug for low-load operation werexxz investigated. The COTS glow plug, used as the ignition assistant (IA), was overdriven beyond its conventional operation range. Engine speed was varied from 1200 RPM to 2100 RPM. Three fuel blends consisting of a jet-A fuel with military additives (F24) and a low cetane number alcohol-to-jet (ATJ) sustainable aviation fuel (SAF) were tested with cetane numbers (CN) of 25.9, 35.5, and 48.5. The ranges of engine speed and fuel cetane numbers studied are significantly larger than those in previous studies of EACI or glow-plug assisted combustion, and the simultaneous variation of engine speed and fuel reactivity are unique to this work. For each speed and fuel, a single-injection of fixed mass was used and the start of injection (SOI) was swept for each IA power.

Smoke emission from compression ignition (CI) engines is directly tied to fuel atomization, vaporization, mixing and combustion processes. Engine boundary conditions such as ambient pressures and temperatures, particularly at higher altitudes, have significant impacts on both available ignition energy and on the mixing-controlled combustion process. However, the effects of boundary conditions are difficult to explore without thorough pressure and temperature control of the engine intake air and exhaust gas at higher altitude conditions. The objective of this research is to investigate the relationship between engine smoke emission and engine power in a CI engine fueled with jet fuel at various ambient conditions including higher altitudes. A multi-cylinder compression-ignition engine was operated on a jet fuel at various ambient pressure and temperature conditions, as low as 60 kPa and -12°C, respectively. Single and multi-injection strategies were applied depending on engine power.

Local deposition of thermal energy can be used to assist the combustion process of low cetane number (CN) fuels in compression-ignition engines, here termed energy-assisted compression ignition (EACI). In the current work, a commercial ceramic glow plug, operated beyond its conventional operation range, was used as the ignition assistant (IA) and sensitivity of fuel jet ignition to operation parameters was studied for two fuels using EACI in an optical engine. A design-of-experiments (DoE) study was devised to determine which engine parameters influenced the energy-assisted pilot injection ignition process the most. The DoE was constructed with four parameters: injection pressure, injected mass, injection timing, and ignition assistant temperature. The fuels used were F24 (Jet-A with military additives) with a cetane number of 48 and a cetane number 35 fuel mixture consisting of 60% F24 and 40% of an alcohol-to-jet fuel (ATJ), blended on a volumetric basis.

The influence of a split-injection strategy on energy-assisted compression-ignition (EACI) combustion of low-cetane number sustainable aviation fuels was investigated in a single-cylinder direct-injection compression-ignition engine using a ceramic ignition assistant (IA). Two low-cetane number fuels were studied: a low-cetane number alcohol-to-jet (ATJ) sustainable aviation fuel (SAF) with a derived cetane number (DCN) of 17.4 and a binary blend of ATJ with F24 (Jet-A fuel with military additives, DCN 45.8) with a blend DCN of 25.9 (25 vol.% F24, 75 vol.% ATJ). A pilot injection mass sweep (3.5-7.0 mg) with constant total injection mass and an injection dwell sweep (1.5-3.0 ms) with fixed main injection timing was performed. Increasing pilot injection mass was found to reduce cycle-to-cycle combustion phasing variability by promoting a shorter and more repeatable combustion event for the main injection with a shorter ignition delay.

The objective of the study was to investigate the spray and combustion characteristics of Jet Propellant-8 (JP-8) using a high-pressure fuel injector which is capable of up to 250-MPa fuel injection pressure. Experiments were performed in a constant-pressure flow-through combustion chamber at the ambient conditions of 825 K and 6 MPa for the oxygen concentration of 0 and 21%. JP-8 was injected over a range of fuel injection pressures from 50 to 250 MPa for single injection events to establish a baseline operation. Pilot and post injections were used to study the effect of multiple injections on spray and combustion of the high-pressure fuel injector. Both pilot and post injection separation times and quantities were systematically varied. JP-8 spray and combustion events were imaged at 75 kHz using a combination of Mie scattering and OH* chemiluminescence imaging.

Current regulations stipulate acceptable levels of particulate emissions based on the mass collected on filters obtained by sampling in diluted exhaust. Although precise, this gives us only aggregated information. If in addition to the mass based measurements, detailed chemical analysis of the particulate matter (PM) is performed, additional subtle information about the combustion process can be revealed. This paper reports the results of detailed chemical analysis of trace metal in the PM emitted from a single cylinder heavy-duty diesel engine. The trace metal concentrations are used as an indicator of oil consumption. Two techniques were used to make the trace metal concentration measurements. PM was captured on filters and trace metals were quantified with an Inductively Coupled Plasma Mass Spectrometer (ICPMS), and also an Aerosol Time-of-Flight Mass Spectrometer (ATOFMS) was used to perform particle size and composition measurements in real time.

This research compares the spray development and combustion characteristics of jet propellant 8 (JP-8) and iso-paraffinic kerosene (IPK) through a range of diesel engine in-cylinder operating conditions. Non-reacting spray experiments were performed in a constant-pressure flow chamber with 99% nitrogen gas composition at constant temperature (900 K) and densities ranging from 11-56 kg/m3. Near-simultaneous, high-speed Mie and schlieren images of the spray were acquired to measure the liquid and vapor penetration lengths of the non-reacting jet. Reacting experiments, consisting of photodiode measurements and intensified high-speed movies of OH* chemiluminescence, were performed at the same thermodynamic conditions as the non-reacting experiments, except with a 21%/79% oxygen/nitrogen ambient gas composition. Measurements of the rate of injection, issued from a single-hole axial common-rail fuel injector, showed negligible differences between the fuels.