Search Results

The effects of cooled EGR on combustion and emission characteristics in HCCI operation region was investigated on a single-cylinder diesel engine, which is fitted with port injection of DME and methanol. The results indicate that EGR rate can enlarge controlled HCCI operating region, but it has little effect on the maximum load of HCCI engine fuelled with DME/methanol dual-fuels. With the increase of EGR rate, the main combustion ignition timing (MCIT) delays, the main combustion duration (MCD) prolongs, and the peak cylinder pressure and the peak rate of heat release decreases. Compared with EGR, DME percentage has an opposite effect on HCCI combustion characteristics. The increase of indicated thermal efficiency is a combined effect of EGR rate and DME percentage. Both HC and CO emissions ascend with EGR rate increasing, and decrease with DME percentage increasing. In normal combustion, NOX emissions are near zero.

Homogeneous charge compression ignition (HCCI) is considered as a high efficient and clean combustion technology for I.C. engines. Methanol is a potential fuel for HCCI combustion. In this research, a single cylinder diesel engine was applied to HCCI operation. Methanol and dimethyl ether (DME) were fueled to the engine by fuel injection system with an electric controlled port in dual fuel mode. The results show that the stable HCCI operation of DME/methanol can be obtained over a quite broad speed and load region. And compared with higher speeds, the load region is even wider at low engine speed. E.g., at the engine speed of 1000 r/min, the maximum indicated mean effective pressure(IMEP) can reach 0.77 MPa, while at 2000r/min it is 0.53 MPa. Both DME and methanol influence HCCI combustion strongly, and by regulating DME/methanol proportions the HCCI combustion process could be controlled effectively.

The effects of various injection timing of methanol on thermo-atmosphere combustion of methanol by port injection of dimethyl ether (DME) and direct injection of methanol were experimentally investigated. The experiment results show that, as injection timing is at 6 degree before TDC, the combustion process comprises three stages: low temperature heat release of DME, high temperature heat release of DME and diffusion combustion of methanol. As injection timing increases, premixed combustion proportion of methanol is increased and diffusion combustion proportion is decreased. As injection timing increases to 126 degree before TDC, diffusion combustion of methanol disappears. At this time, the combustion process shows typical two stages heat release of HCCI combustion. As injection timing increases, required DME rate is increased, combustion efficiency and indicated thermal efficiency all first increase and then decrease.

With a zero-dimensional detailed chemical kinetic model, a numerical study was carried out to investigate the chemical reaction phenomena encountered in the homogenous charge compression ignition process of dimethyl ether (DME) and methane dual fuel. The results show that the DME/methane dual fuel elementary reactions affect each other. The low temperature reaction (LTR) of DME is inhibited, the second molecular oxygen addition of DME is restrained, and β -scission plays a dominant role in DME oxidation. Hydrogen peroxide (H2O2) is controlled by DME oxidation and almost has no correlation with methane oxidation. The rich H2O2 concentration makes methane oxidation occurs at low initial temperature. Most of the formaldehyde (CH2O) is produced from H-abstraction of methoxy (CH3O) rather than from LTR of the DME. However, the heat release of methane oxidation promotes the hot flame reactions of DME which make the reactions with high activation energy occur.

A very competitive alcohol for use in diesel engines is butanol. Butanol is of particular interest as a renewable bio-fuel, as it is less hydrophilic and it possesses higher heating value, higher cetane number, lower vapor pressure, and higher miscibility than ethanol or methanol. These properties make butanol preferable to ethanol or methanol for blending with conventional diesel or gasoline fuel. In this paper, the spray and combustion characteristics of pure n-butanol fuel was experimentally investigated in a constant volume combustion chamber. The ambient temperatures were set to 1000 K, and three different oxygen concentrations were set to 21%, 16%, and 10.5%. The results indicate that the penetration length reduces with the increase of ambient oxygen concentration. The combustion pressure and heat release rate demonstrate the auto-ignition delay becomes longer with decreasing of oxygen concentrations.