Search Results

Small remotely piloted aircraft (10-25 kg) powered by internal combustion engines typically operate on motor gasoline, which has an anti-knock index (AKI) of >80. To comply with the single-battlefield-fuel initiative in DoD Directive 4140.25, interest has been increasing in converting the 1-10 kW power plants in the aforementioned size class to run on lower AKI fuels such as diesel and JP-8, which have AKIs of ~20. It has been speculated that the higher losses (short-circuiting, incomplete combustion, heat transfer) that cause these engines to have lower efficiencies than their conventional-scale counterparts may also relax the fuel-AKI requirements of the engines. To investigate that idea, the fuel-AKI requirement of a 3W-55i engine was mapped and compared to that of the engine on the manufacturer-recommended 98 octane number (ON) fuel.

As the cost and complexity of modern aircraft systems increases, emphasis has been placed on model-based design as a means for reducing development cost and optimizing performance. To facilitate this, an appropriate modeling environment is required that allows developers to rapidly explore a wider design space than can cost effectively be considered through hardware construction and testing. This wide design space can then yield solutions that are far more energy efficient than previous generation designs. In addition, non-intuitive cross-coupled subsystem behavior can also be explored to ensure integrated system stability prior to hardware fabrication and testing. In recent years, optimization of control strategies between coupled subsystems has necessitated the understanding of the integrated system dynamics.

As IC engines decrease in displacement, their cylinder surface area to swept volume ratio increases. Examining power output of IC engines with respect to cylinder surface area to swept volume ratio shows that there is a change in power scaling trends at approximately 1.5 cm−1. At this size, it is suggested that heat transfer from the cylinder becomes the dominant thermal loss mechanism and performance and efficiency characteristics suffer. Furthermore, small IC engines (>1 cm−1) have limited technical performance data compared to IC engines in larger size classes. Therefore, it is critical to establish accurate performance figures for a family of geometrically similar engines in the size class of approximately 1.5 cm−1 in order to better understand the thermal losses that contribute to lower efficiencies in small IC engines. The engines considered in this scaling study were manufactured by 3W Modellmotoren, GmbH.

Two compact intercoolers are designed for the Rotax 914 aircraft engine to increase engine power and avoid engine knock. A study is performed to investigate the effects of unsteady airflow on intercooler performance. Both intercoolers use air-to-liquid cross flow heat exchangers with staggered fins. The intercoolers are first tested by connecting the four air outlets of the intercooler to a common restricted exit creating a constant back pressure which allows for steady airflow. The intercoolers are then tested by connecting the four air outlets to a 2.4 liter, 4 cylinder engine head and varying the engine speed from 6000 to 1200 RPM corresponding to decreasing flow steadiness. The test is performed under average flight conditions with air entering the intercooler at 180°F and about 5 psig. Results from the experiment indicate that airflow unsteadiness has a significant effect on the intercooler's performance.

An experimental study is performed to investigate the possibility of relaxing the octane requirement of a Rotax 914 engine equipped with a pre-chamber jet ignition system. A pre-chamber jet igniter with no auxiliary fuel addition is designed to replace the spark plug in cylinder two of the test engine and is evaluated across engine speeds ranging from 2500 to 5500 RPM. Experiments are performed across both normally aspirated and boosted configurations using regular 87 AKI gasoline fuel. Normally aspirated results at 98 kPa manifold absolute pressure show a 7-10° burn rate improvement with the jet ignition combustion system. Tests to determine the maximum load at optimal combustion phasing (no spark retard) are then conducted by increasing boost pressure up to maximum knock limits.

A two-port fuel-injection (PFI) system is added to a Rotax 914 four-cylinder spark-ignition engine to allow two fuels of different reactivity to be injected simultaneously in order to vary the fuel octane number during engine operation. Engine performance using the dual-fuel PFI system is compared to that using injection of primary-reference-fuel (PRF) blends via a single-PFI system for fuel octane ratings of 50, 70, and 87 octane. The on-the-fly octane control of dual-PFI system is found to control fuel-octane well enough to produce maximum indicated mean effective pressure (IMEPn) results within ± 2% of single-PFI PRF IMEPn results. IMEPn is compared among dual-PFI blends from 20 to 87 octane, neat n-heptane, neat JP-8, and JP-8/isooctane blends. Maximum IMEPn for these fuels is established for the Rotax 914 engine operating from 2500 to 5800 rev/min.

Modern military engines desire both the fuel efficiency of high-bypass turbofans and the high specific thrust of a low-bypass turbofan. Using traditional engine architectures, performance and efficiency are in conflict, so an engine is usually designed to best meet requirements for its primary mission. While the concept of a variable cycle engine is not new, recent advances in engine architecture technology suggest that adding a second bypass stream to a traditional turbofan can provide significant benefits. This “third stream” (the core flow being the primary stream and the inner bypass being the second stream) airflow can be independently modulated so that engine airflow demand can be matched with the available inlet flow at a variety of operating points, thereby reducing spillage drag. Additionally, the third stream air provides a valuable heat sink for cooling turbine cooling air or dissipating other aircraft heat loads.

This paper presents the concept of a dual latent heat sink for thermal management of pulse heat generating electronic systems. The focus of this work is to verify the effectiveness of the concept during charging through experimentation. Accordingly, custom components were built and a prototype version of the heat sink was fabricated. Experiments were performed to investigate the implementation feasibility and heat transfer performance. It is shown that this heat sink is practicable and helps in arresting the system temperature rise during charging (period of pulse heat load).

The two-phase flow modeling is done using the level set method to identify the interface of vapor and liquid. The modifications to the incompressible Navier-Stokes equations to consider surface tension, viscosity, gravity and phase change are discussed in detail. The governing equations are solved using finite difference method. In the present work, investigations on the effect of thermal conductivity and latent heat of vaporization of liquid on heat transfer in a 44 µm thick liquid film containing vapor bubble with droplet impact is investigated. The importance of thermal conductivity and latent heat of vaporization of liquid on heat transfer is identified. The variation of heat flux with thermal conductivity and latent heat is plotted. The computed liquid and vapor interface, velocity vector and temperature distributions at different time instants are also visualized for better understanding of the heat removal.

Advances in the past decade of the energy and power densities of lithium-ion based batteries for hybrid electric vehicles and various consumer applications have been substantial. Rechargeable high rate lithium-ion batteries are now exceeding 6 kW/kg for short discharge times (<15 seconds). Rechargeable lithium-ion polymer batteries, for applications such as remote-control aircraft, are achieving simultaneously high energy density and high power density (>160 Whr/kg at >1.0 kW/kg). Some preliminary test data on a rechargeable lithium-ion polymer battery is presented. The use of high rate rechargeable lithium-ion batteries as a function of onboard power, electric laser power level, laser duty cycle, and total mission time is presented. A number of thermal management system configurations were examined to determine system level weight impacts. Lightweight configurations would need a regenerative thermal energy storage subsystem.

The detrimental effects of prolonged sitting during long-duration flights include deep vein thrombosis, pressure sores, and decreased awareness and performance. However, the cushion is often the only component of the ejection seat system that can be modified to mitigate these effects. This study investigated the long-duration effects of sitting in four ejection seat cushions over eight hours. Subjective comfort survey data and cognitive performance data were gathered along with comparative objective data, including seated pressures, muscular fatigue levels, and lower extremity oxygen saturation. Peak seated pressures ranged from 1.22–3.22 psi. Oxygen saturation in the lower extremities decreased over the eight hours. Cognitive performance increased over time regardless of cushion with the exception of the dynamic cushion, which induced a decrease in performance for females.

Rotating Heat Pipe (RHP) technolog y is being developed for high speed (>20 krpm) regimes of electric motor/generator cooling. The motivation for this research is the potential application of the high speed RHPs for the thermal management of advanced rotating electrical machines. The passive nature and relatively simple features of this device are attractive for the removal of waste heat from the rotors of electric machines. Interesting air-cooling experimental results of two high speed RHPs designed, fabricated and tested at AFRL are presented here. Emphasis is made on external heat removal concepts useful for cooling the RHP condenser in order to be successful in promoting this technology to real world problems.