Search Results

Regarding the solution for various issues on engine tribology, in order to understand the involvement of temperature in the friction and scuffing under the mixed and/or boundary lubrication regime, the two cases of piston ring & cylinder liner and cam & tappet were analytically studied. The friction between sliding interfaces is composed of four shear stresses from the viscous oil-films, the adsorbed oil molecules, the tribofilms due to oil additives, and the true metal contacts on surface asperities. Since all the shear stress have exponential temperature dependences, the relationship between the frictional shear stress and temperature is assumed to be expressed by the Arrhenius equation. Through analyzing friction data measured in laboratory tests conducted under the same temperature and sliding conditions as during the break-in of engines, various levels of temperature involvement were clarified.

A mean value turbocharged engine model is useful in terms of accuracy and convenience for fuel economy strategies or engine controller development. Turbocharging process is a feedback system with a positive gain, i.e. increasing exhaust work leads to increasing a cycle work. The gain of the feedback system is determined mainly by exhaust work ratio in a cycle and inertia of the turbine. The work ratio was investigated based on engine test with EGR. A turbocharging process model was obtained using the work ratio in a cycle and theoretical equations. The model is applied to investigate manifold absolute pressure response with EGR.

Gasoline engines have the trace-knock phenomena induced by the fast combustion which happens a few times during 100 cycles. And that constrains the thermal efficiency improvement due to limiting the ignition timing advance. So the authors have been dedicating a trace-knock simulation so that we could obtain any pieces of information associated with trace-knock characteristics. This simulation consists of a turbulent combustion model, a cycle-by-cycle variation model and a chemical calculation subprogram. In the combustion model, a combustion zone is considered in order to obtain proper turbulent combustion speed through wide range of engine speed. From a cycle-by-cycle variation analysis of an actual gasoline engine, some trace-knock features were detected, and they were involved in the cycle-by-cycle variation model. And a reduced elementary reaction model of gasoline PRF (primary reference fuel) was customized to the knocking prediction, and it was used in the chemical calculation.

Improving fuel efficiency often affects NVH performance. Modifying a vehicle’s design in the latter stages of development to improve NVH performance is often costly. Therefore, to optimize the cost performance, a Multi-Attribute Balancing (MAB) approach should be employed in the early design phases. This paper proposes a solution based on a unified 1D system simulation model across different vehicle performance areas. In the scope of this paper the following attributes are studied: Fuel economy, Booming, Idle, Engine start and Drivability. The challenges to be solved by 1D simulation are the vehicle performance predictions, taking into account the computation time and accuracy. Early phase studies require a large number of scenarios to evaluate multiple possible parameter combinations employing a multi-attribute approach with a systematic tool to ease setup and evaluation according to the determined performance metrics.

It is effective in engine fuel economy to reduce the viscous friction by applying lubricating oil with low viscosity. The lower viscosity such as SAE0W20, however, increase lubricating oil consumption, LOC. In addition, it has become urgent to reduce the LOC because the emission of the sulfide ash, phosphorous and sulfur contents degrades the diesel particulate filter and the de-NOx catalyst, in addition to which the emission of metal oxide contents from oil additives can cause pre-ignition in highly supercharged spark ignition engines. In order to clarify the LOC mechanism of low viscosity oils, the LOC rates were measured with a supercharged diesel engine under various operating conditions when lubricated with SAE30 or SAE10W30 test oil, and the resulting data have been compared with the rates of the evaporation from the oil-film on the cylinder wall, LOE, as predicted by the devised analysis method for multi-species component oils.

Recently, the evaluation of the thermal environment of an engine compartment has become more difficult because of the increased employment and installation of turbochargers. This paper proposes a new prediction model of the momentum source for the turbine of a turbocharger, which is applicable to three-dimensional thermal fluid analyses of vehicle exhaust systems during the actual vehicle development phase. Taking the computational cost into account, the fluid force given by the turbine blades is imitated by adding an external source term to the Navier-Stokes equations corresponding to the optional domain without the computational grids of the actual blades. The mass flow rate through the turbine, blade angle, and number of blade revolutions are used as input data, and then the source is calculated to satisfy the law of the conservation of angular momentum.

Torque profile control is one of required technologies for propulsion engines. A smaller parametric model is more preferable for control algorithm design and evaluation. Mean value engine torque can be obtained from throttle opening change using a transfer function. A transfer function for a turbocharged engine was investigated with thermo-dynamic equations for a turbine and a compressor and test data. A small turbocharged engine was tested to model the air transfer process. Turbine speed was measured with temperatures, pressures and air mass flow. Turbine speed response is like a first order system to air mass flow into a combustion chamber. The pressure ratio at the compressor is approximated by a curve proportional to the turbine speed square. Based on those findings, a reduced order model for describing dynamic air transfer process with a turbocharger was constructed. The proposed model is compact and suitable for engine torque control design and controller implementation.

Downsizing engines with a turbocharging system have been widely applied to passenger cars to improve fuel economy. Engine torque response to accelerator operation is one of important features in addition to steady state performance of the system. Torque profile management for turbocharged internal combustion engines is one of required technologies. A turbocharging system for a car is a system with a positive feedback loop in which compressed air drives the compressor after the combustion process. A reduced order model was derived for the charging system. Pressure ratio of a compressor is proportional to square of turbine speed and the turbine speed is a first order delay system to throttle opening in the model. Model structure was designed from mathematical equations that describe turbine and compressor works. Model parameters were identified from measured data. An output torque profile control strategy based on the derived model is investigated.

A KIVA code which is customized for passenger car's diesel engines is linked with an engine performance simulator and demonstrated with our optimizing calculation system. Aiming to fulfill our target calculation speed, the combustion model of the KIVA code is changed from a chemical reaction calculation method to a chemical equilibrium calculation method which is introduced a unique technique handling chemical species maps. Those maps contain equilibrium mole fraction data of chemical species according to equivalence ratio and temperature. Linking the KIVA code to the engine simulator helps to evaluate engine performance by indicated mean effective pressure (IMEP). The optimizing calculation system enables to obtain response surfaces. Observing the response surfaces, clear views of engine performance characteristics can be seen. The overview of this calculation system and some examples of the calculation are shown in this paper.

Compression ratio of newly developed gasoline engines has been increased in order to improve fuel efficiency. But in-cylinder pressure around top dead center (TDC) before spark ignition timing is higher than expectation, because the low temperature oxidization (LTO) generates some heat. The overview of introduced calculation method taking account of the LTO heat of unburned gas, how in-cylinder pressure is revised and some knowledge of knocking prediction using chemical kinetics are shown in this paper.

Outwardly propagating stoichiometric flames of H2/CH4/air were studied in a constant volume fan-stirred combustion chamber in order to investigate the effects of hydrogen concentration on the turbulent burning velocities. The experiments were conducted at mixture temperature of 350 K and mixture pressure of 0.10 MPa. The mole fraction of hydrogen in the binary fuel was varied from 0 to 1.0 for turbulence intensities equal to 1.23, 1.64 and 2.46 m/s. Laminar flames of the mixtures were first investigated to obtain the unstretched laminar burning velocities and the associated Markstein numbers. The unstretched laminar burning velocity increased non-linearly with increase in hydrogen fraction. The Markstein number and the effective Lewis number of the mixtures varied non-monotonically with hydrogen mole fraction. The Markstein number was used to investigate the influence of thermo-diffusive effects on the turbulent burning velocity.

An ESC hydraulic modulator contains on/off valves and proportional valves. A complex model of one proportional valve is detailed and used as a basis for model reduction the activity index technique. One interesting aspect is that the technology of the proportional valves remains (i.e. ball valves under conical seat). As such, the parameters are physical parameters forming the ones to master (manufacturing tolerances) by the supplier to also master the dynamic behavior of the system. Once this has been done, a complete model of half an ESC braking circuit is built including the pump, the reservoir, the pipes and hoses as well as the calipers. The activity index technique is thus reused on the circuit to further reduce it to finally obtain a modeling level acceptable for real time purpose.

This paper presents a method and corresponding software implementation for powertrain (PWT) mounting system layout design for decoupling rigid-body modes in the torque roll axis system. The novelty in the proposed method is that it requires a minimal set of inputs for determining mount topology, orientation and stiffness properties for decoupling powertrain modes, and as such it can be used at early design stages, unlike the conventional approaches based on analysis and optimization techniques. Consequently, PWT mounts can be positioned and oriented close to their optimal configuration, allowing to develop more realistic full vehicle models for conceptual (or early stage) designs and to run a more accurate dynamic analysis concerning secondary ride and vibrations. The proposed methodology is illustrated on a powertrain mounting system design example case.

This paper presents a new time-domain source contribution analysis method for in-room pass-by noise. The core of the method is a frequency-domain ASQ model (Airborne Source Quantification) representing each noise generating component (engine, exhaust, left and right tyres, etc.) by a number of acoustic sources. The ASQ model requires the measurement of local FRF's and acoustic noise transfer functions to identify the operational loads from nearby pressure indicator responses and propagate the loads to the various target microphones on the sides of the vehicle. Once a good ASQ model is obtained, FIR filters are constructed, allowing a time-domain synthesis of the various source contributions to each target microphone. The synthesized target response signals are finally recombined into a pass-by sound by taking into account the speed profile of the vehicle.

Driving car means to control a vehicle according to a target path, e.g. road and speed, with some constraints. Human driving models have been proposed and applied for simulations. However, human control in driving has not been analyzed sufficiently comparing with that of machine control system in term of control theory. Input - output property with internal information processing is not easily measured and described. Response of human driving is not as quicker as that of machine controller but human can learn vehicle response to driving operation and predict target changes. Driving behavior of an expert driver and a beginner in an emission test cycle was measured and difference in target speed tracking was looked into with performance indices. The beginner's operation was less stable than that of the expert. Transfer function of the vehicle system was derived based on linearized model to investigate human driving behavior as a tracking controller in the system.

Acoustic performance of vehicle engines is a real challenge for powertrain design engineers. Quiet engines are required to reduce noise pollution and satisfy pass-by noise regulations, but also to improve the driving comfort. Simulation techniques such as the Boundary Element Method (BEM) have already been available for some time and allow predicting the vibro-acoustic response of engines. Although the accuracy of these simulation techniques has been proven, a challenge still remains in the required computation time. Given the large amount of speeds for a full engine run-up and the need to cover a large frequency range, computation times are significant, which limits the possibility to perform many design iterations to optimize the system. In 2001, Acoustic Transfer Vectors (ATV) [1] have been presented to adequately deal with multiple rpm. The ATV provide the acoustic response for unit surface velocities and are therefore independent from the engine's actual surface vibrations.

Magnesium alloys have been used and developed in applications for various motorcycle components and others such as cylinder head cover, crankcase and oil pan due to light weight, high specific strength and recycles ability. However, many of those alloys suffer from inferior die cast ability and high temperature properties, such as creep resistant. Ryobi limited has developed the creep resistant alloy in order to be utilized for the various motorcycle components and so forth. The properties of new die cast creep resistant alloy have been introduced. The targets for development of the properties of new alloy are the same creep resistant as aluminum die cast alloys and the same diecastability as ASTM magnesium alloys, such as AZ91D or AM60B alloys. Specific approaches of development with several types of evaluation have been performed for the purpose of fulfillment of this goal.

The present study introduces a multi-component model for heavy fuel oil combustion based on two component approximation, implemented into KIVA-3V using modified evaporation, ignition and combustion models. The fuel is treated as a blend of residual portion and cutter stocks. Different fuel properties are assigned to each component affecting evaporation behavior in the liquid phase as well as ignition and combustion characteristics in the vapor phase. The model was validated regarding spray and flame appearance using photographs of spray combustion in a visual constant volume combustion chamber. Further the effects of fuel component properties on the ignition and combustion properties of the fuel blend have been investigated based on rate of heat release analysis.

When pickup trucks are driven on concrete paved freeways, freeway hop shake is a major complaint. Freeway hop shake occurs when the vehicle passes over the concrete joints of the freeway which impose in-phase harmonic road inputs. These road inputs excite vehicle modes that degrade ride comfort. The worst shake level occurs when the vehicle speed is such that the road input excites the vehicle 1st bending mode and/or the rear wheel hop mode. The hop and bending mode are very close in frequency. This phenomenon is called freeway hop shake. Automotive manufacturers are searching for ways to mitigate freeway hop shake. There are several ways to reduce the shake amplitude. This paper documents a new approach using hydraulic body mounts to reduce the shake. A full vehicle analytical model was used to determine the root cause of the freeway hop shake.

This paper presents a CAE based approach to accurately simulate and optimize Ride and Handling metrics. Because of the wide range of vehicle phenomena involved, across the variety of frequency ranges, it is essential that the vehicle model includes proper representation of the dynamic properties of the various subsystems (e.g. tires, steering, PT, etc.) Precise correlation between test and simulation for standalone vehicle components and systems is achieved by replicating in the MBS (Multi-body Simulation) the same tests and boundary conditions. This allows the analyst to correctly define those crucial elements and parameters which have the greatest effect on the R&H attribute to be investigated. Setting up the simulation to correctly represent only one single maneuver simulation at a time would not allow the analyst to consider how the dynamic properties of the chassis design variables should be tuned to achieve to best balance and trade-offs.