Search Results

The introduction of alternative fuels is crucial to limit greenhouse gases. CNG is regarded as one of the most promising clean fuels given its worldwide availability, its low price and its intrinsic properties (high knocking resistance, low carbon content...). One way to optimize dedicated natural gas engines is to improve the CNG slow burning velocity compared to gasoline fuel and allow lean burn combustion mode. Besides optimization of the combustion chamber design, hydrogen addition to CNG is a promising solution to boost the combustion thanks to its fast burning rate, its wide flammability limits and its low quenching gap. This paper presents an investigation of different methane/hydrogen blends between 0% and 40 vol. % hydrogen ratio for three different combustion modes: stoichiometric, lean-burn and stoichiometric with EGR.

Latest emissions standards impose very low NOx and particle emissions that have led to new Diesel combustion operating conditions, such as low temperature combustion (LTC). The principle of LTC is based on enhancing air fuel mixing and reducing combustion temperature, reducing raw nitrogen oxides (NOx) and particle emissions. However, new difficulties have arisen. LTC is typically achieved through high dilution rates and low CR, resulting in increased auto-ignition delay that produces significant noise and deteriorates the combustion phasing. At the same time, lower combustion temperature and reduced oxygen concentration increases hydrocarbon (HC) and carbon oxide (CO) emissions, which can be problematic at low load. Therefore, if LTC is a promising solution to meet future emission regulations, it imposes a new emissions, fuel consumption and noise trade-off. For this, the injection strategy is the most direct mean of controlling the heat release profile and fuel air mixture.

The benefits of running on ethanol-blended fuels are well known, especially global CO₂ reduction and performances increase. But using ethanol as a fuel is not drawbacks free. Cold start ability and vehicle autonomy are appreciably reduced. These two drawbacks have been tackled recently by IFP and its partners VALEO and Cristal Union. This article will focus on the second one, as IFP had the responsibility to design the powertrain of a fully flex-fuel vehicle (from 0 to 100% of ethanol) with two main targets: reduce the fuel consumption of the vehicle and maintain (at least) the vehicle performances. Using a MPI scavenging in-house concept together with turbocharging, as well as choosing the appropriate compression ratio, IFP managed to reach the goals.

In order to address the CO₂ emissions issue and to diversify the energy for transportation, CNG (Compressed Natural Gas) is considered as one of the most promising alternative fuels given its high octane number. However, gaseous injection decreases volumetric efficiency, impacting directly the maximal torque through a reduction of the cylinder fill-up. To overcome this drawback, both independent natural gas and gasoline indirect injection systems with dedicated engine control were fitted on a RENAULT 2.0L turbocharged SI (Spark Ignition) engine and were adapted for simultaneous operation. The main objective of this innovative combination of gas and liquid fuel injections is to increase the volumetric efficiency without losing the high knocking resistance of methane.

Diversifying energy resources and reducing greenhouse gas emissions are key priorities in the forthcoming years for the automotive industry. Currently, among the different solutions, sustainable biofuels are considered as one of the most attractive answer to these issues. This paper deals with the vehicle application of an innovative diesel fuel formulation using Ethanol to tackle these future challenges. The main goal is to better understand the impact of using biofuel blends on engine behavior, reliability and pollutants emissions. This alternative oxygenated fuel reduces dramatically particulate matter (PM) emissions; this paves the way to improve the NOx/PM/CO₂ trade-off. Another major interest is to avoid adding a particulate filter in the exhaust line and to avoid modifying powertrain and vehicle hardware and therefore to minimize the overall cost to fulfill upcoming emission regulations.

Among the existing concepts that help to improve the efficiency of spark-ignition engines at part load, Controlled Auto-Ignition™ (CAI™) is an effective way to lower both fuel consumption and pollutant emissions. This combustion concept is based on the auto-ignition of an air-fuel-mixture highly diluted with hot burnt gases to achieve high indicated efficiency and low pollutant emissions through low temperature combustion. To minimize the costs of conversion of a standard spark-ignition engine into a CAI engine, the present study is restricted to a Port Fuel Injection engine with a cam-profile switching system and a cam phaser on both intake and exhaust sides. In a 4-stroke engine, a large amount of burnt gases can be trapped in the cylinder via early closure of the exhaust valves. This so-called Negative Valve Overlap (NVO) strategy has a key parameter to control the amount of trapped burnt gases and consequently the combustion: the exhaust valve-lift profile.

Among the last years, environmental concerns have raised the interest for biofuels. Ethanol, blended with gasoline seems particularly suited for the operation of internal combustion engines, and has been in use for severals years in some countries. However, it has a strong impact on engine performance, which is emphasized on recent engine architectures, with downsizing through turbocharging and variable valve actuation. Taking all the benefits of ethanol-blended fuel thus requires an adaptation of the engine management system. This paper intends to assess the effect of gasoline-ethanol blending from this point of view, then to describe a mean-value model of a fuel-flexible turbocharged PFI-SI engine, which will serve as a basis for the development of control algorithms. The focus will be in this paper on ethanol content estimation in the blend, supported by both simulation and experimental results.

While fuel efficiency has to be improved, future Diesel engine emission standards will further restrict vehicle emissions, particularly of nitrogen oxides. Increased in-cylinder filling is recognized as a key factor in addressing this issue, which calls for advanced design of air and exhaust gas recirculation circuits and high cooling capabilities. As one possible solution, this paper presents a 2-stage boosting breathing architecture, specially dedicated to improving the trade-off between emissions and fuel consumption instead of seeking to improve specific power on a large family vehicle equipped with a 1.6-liter Diesel engine. In order to do it, turbocharger matching was specifically optimized to minimize engine-out NOx emissions at part-load and consumption under common driving conditions. Engine speed and load were analyzed on the European driving cycle. The key operating points and associated upper boundary for NOx emission were identified.

An unified model with a single set of kinetic parameters has been proposed for modeling laminar flame velocities of several alkanes using detailed kinetic mechanisms automatically generated by the EXGAS software. The validations were based on recent data of the literature. The studied compounds are methane, ethane, propane, n-butane, n-pentane, n-heptane, iso-octane, and two mixtures for natural gas and surrogate gasoline fuel. Investigated conditions are the following: unburned gases temperature was varied from 300 to 600 K, pressures from 0.5 to 25 bar, and equivalence ratios range from 0.4 to 2. For the overall studied compounds, the agreement between measured and predicted laminar burning velocities is quite good.

The simultaneous reduction of engine-out nitrogen oxide (NOx) and particulate emissions via low-temperature combustion (LTC) strategies for compression-ignition engines is generally achieved via the use of high levels of exhaust gas recirculation (EGR). High EGR rates not only result in a drastic reduction of combustion temperatures to mitigate thermal NOx formation but also increases the level of pre-mixing thereby limiting particulate (soot) formation. However, highly pre-mixed combustion strategies such as LTC are usually limited at higher loads by excessively high heat release rates leading to unacceptable levels of combustion noise and particulate emissions. Further increasing the level of charge dilution (via EGR) can help to reduce combustion noise but maximum EGR rates are ultimately restricted by turbocharger and EGR path technologies.

Single cylinder optical engines are used for internal combustion (IC) engine research as they allow for the application of qualitative and quantitative non-intrusive, diagnostic techniques to study in-cylinder flow, mixing, combustion and emissions phenomena. Such experimental data is not only important for the validation of computational models but can also provide a detailed insight into the physical processes occurring in-cylinder which is useful for the further development of new combustion strategies such as gasoline homogeneous charge compression ignition (HCCI) and Diesel low temperature combustion (LTC). In this context, it is therefore important to ensure that the performance of optical engines is comparable to standard all-metal engines. A comparison of optical and all-metal engine combustion and emissions performance was performed within the present study.

The authors present the supervisory control of a parallel hybrid powertrain, focusing on several issues related to the real-time implementation of optimal control based techniques, such as the Equivalent Consumption Minimization Strategies (ECMS). Real-time implementation is introduced as an intermediate step of a complete chain of tools aimed at investigating the supervisory control problem. These tools comprise an offline optimizer based on Pontryagin Minimum Principle (PMP), a two-layer real-time control structure, and a modular engine-in-the-loop test bench. Control results are presented for a regulatory drive cycle with the aim of illustrating the benefits of optimal control in terms of fuel economy, the role of the optimization constraints dictated by drivability requirements, and the effectiveness of the feedback rule proposed for the adaptation of the equivalence factor (Lagrange multiplier).

The combination of air charging and downsizing is known to be an efficient solution to reduce CO2 emissions of modern gasoline engines. The decrease of the cubic capacity and the increase of the specific performance help to reduce the fuel consumption by limiting pumping and friction losses and even the losses of energy by heat transfer. Investigations have been conducted on a highly downsized SI engine to confirm if a strong decrease of the displacement (50 %) was still interesting regarding the fuel consumption reduction and if other ways were possible to improve further more its efficiency. The first aim of our work was to identify the optimal design (bore, stroke, displacement, …) that could maximize the consumption reduction potential at part load but also improve the engine's behaviour at very high load (up to 3.0 MPa IMEP from 1000 rpm). In order to do that, four engine configurations with different strokes and bores have been tested and compared.

Facing more and more stringent regulations, new solutions are developed to decrease pollutant emissions. One of them have shown promising and relevant results. It consists of the use of ethanol as a blending component for diesel fuel Nevertheless, the addition of ethanol to Diesel fuel affects some key properties such as the flash point. Consequently, Diesel blends containing ethanol become highly flammable at a temperature around ambient temperature. This study proposes to improve the formulation of ethanol based diesel fuel in order to avoid flash point drawbacks. First, a focus on physical and chemical properties is done for ethanol based diesel fuels with and without flash point improvement. Second, blends are tested on a passenger car diesel engine, under a wide operating range conditions from low load low speed up to maximum power. The main advantage of the ethanol based fuels generate low smoke level, that allows using higher EGR rate, thus leading to an important NOx decrease.

Facing the CO2 emission reduction challenge, the combination of downsizing and turbocharging appears as one of the most promising solution for the development of high efficiency gasoline engines. In this context, as knock resistance is a major issue, limiting the performances of turbocharged downsized gasoline engines, fuel properties are more than ever key parameters to achieve high performances and low fuel consumption's levels. This paper presents a combustion study carried out into the GSM consortium of fuel quality effects on the performances of a downsized turbocharged Direct Injection SI engine. The formulation of two adapted fuel matrix has allowed to separate and evaluate the impacts of three major fuel properties: Research Octane Number (RON), Motor Octane Number (MON) and Latent Heat of Vaporization (LHV). Engine tests were performed on a single cylinder engine at steady state operating condition.

Engine downsizing is one of the most promising engine solutions to improve efficiency, but requires higher specific performance because of a lower engine displacement. The study is based on experimental work performed with an IFP prototype single cylinder engine, representative of passenger car applications. This engine enables very high specific power, with a high level of thermal and mechanical constraints. Tests were carried out on both full load and part load operation with a prototype common rail equipment capable of very high fuel pressure (up to 250 MPa). Results show that increasing fuel flow rate using fuel injection pressure instead of increasing nozzle hole diameter is more advantageous at full load, mainly because a lower nozzle hole diameter improves air entrainment. Benefits observed with increased injection pressure are enhanced when associated with upgraded engine thermo-mechanical limits, and advanced turbo charging system.

This work studies the potential of ethanol-Biodiesel-Diesel fuel blends in both conventional Diesel and HCCI combustion modes. First, ethanol based fuels were tested on a modern commercial multi-cylinder DI diesel engine. The aim of this phase was to assess how such fuels affect Diesel engine performances and emissions. These results indicate that low levels of PM and NOx emissions, with a contained fuel consumption penalty and with an acceptable noise level, are achievable when the Diesel-ethanol blends are used in combination with an optimized combustion control. Moreover, experiments with ethanol based blends were performed using a single cylinder engine, running under both early injection HCCI and Diesel combustion modes. Compared to a conventional fuel, these blends allow increasing the HCCI operating range and also lead to higher maximum power output in conventional Diesel combustion.

New combustion processes like LTC (Low Temperature Combustion) that includes HCCI (Homogeneous Charge Compression Ignition), PCCI (Premixed Charge Compression Ignition), PPCI (Partial Premixed Compression Ignition)… are promising ways to reduce simultaneously NOx and PM. Nevertheless, these combustion processes can be used only on a limited part of the engine load and speed map. Therefore, it appeared interesting to assess how the fuel, through its characteristics, could enhance the operating range in such combustion processes. That was the aim of an international consortium carried out by IFP and supported by numerous industrial companies. First a specific procedure has been developed to compare the different fuels on a early injection HCCI single cylinder engine. Then, using this procedure, a matrix of fuels having different cetane numbers (CN = 40-63), volatilities and chemical compositions has been tested.

Environment protection issues regarding CO2 emissions as well as customers requirements for fun-to-drive and fuel economy explain the strong increase of Diesel engine on European market share in all passenger car segments. To comply future purposes of emission regulations, particularly dramatic decrease in NOx emissions, technology need to keep upgrading; the reduction of the volumetric compression ratio (VCR) is one of the most promising research ways to allow a simultaneous increase in power at full load and NOx / PM trade-off improvement at part load. This study describes the combustion effects of the reduction of compression ratio and quantifies improvements obtained at full load and part load running conditions on a HSDI Common Rail engine out performance (power, fuel consumption, emissions and noise). Potential and limitations of a reduced compression ratio from 18:1 to 14:1 are underlined.

Low temperature combustion concept as HCCI is one of the most promising research ways to comply future emission regulations of Diesel passenger vehicles. IFP promoted this concept with NADI™ (Narrow Angle Direct Injection) combustion design whose original approach lies on a fuel spray guided by the bowl central tip to the re-entrant. For full load operating range, one of the key issue for success is to use as much as possible available air in the combustion chamber in order to reach low value of air fuel ratio, and therefore high value of specific power and specific torque. In this study, engine tests on a single cylinder engine with NADI™ concept are performed at full load; 3-D calculations as well as air/fuel mixing process visualizations in a constant volume vessel with optical access allowed to establish criteria for helping future combustion system design for full load operation.