Search Results

In an engine system, the piston pin is subjected to high loading and severe lubrication conditions, and pin seizures still occur during new engine development. A better understanding of the lubricating oil behavior and the dynamics of the piston pin could lead to cost- effective solutions to mitigate these problems. However, research in this area is still limited due to the complexity of the lubrication and the pin dynamics. In this work, a numerical model that considers structure deformation and oil cavitation was developed to investigate the lubrication and dynamics of the piston pin. The model combines multi-body dynamics and elasto-hydrodynamic lubrication. A routine was established for generating and processing compliance matrices and further optimized to reduce computation time and improve the convergence of the equations. A simple built-in wear model was used to modify the pin bore and small end profiles based on the asperity contact pressures.

This paper reviews the relevant literature on the effects of sulfated ash, phosphorus, and sulfur on DPF, LNT, and SCR catalysts. Exhaust backpressure increase due to DPF ash accumulation, as well as the rate at which ash is consumed from the sump, were the most studied lubricant-derived DPF effects. Based on several studies, a doubling of backpressure can be estimated to occur within 270,000 to 490,000 km when using a 1.0% sulfated ash oil. Postmortem DPF analysis and exhaust gas measurements revealed that approximately 35% to 65% less ash was lost from the sump than was expected based on bulk oil consumption estimates. Despite significant effects from lubricant sulfur and phosphorus, loss of LNT NOX reduction efficiency is dominated by fuel sulfur effects. Phosphorus has been determined to have a mild poisoning effect on SCR catalysts. The extent of the effect that lubricant phosphorus and sulfur have on DOCs remains unclear, however, it appears to be minor.

The life of an automotive engine is often limited by the ability of its components to resist wear. Zinc dialkyldithiophosphate (ZDDP) is an engine oil additive that reduces wear in an engine by forming solid antiwear films at points of moving contact. The effects of this additive are fairly well understood, but there is little theory behind the kinetics of antiwear film formation and removal. This lack of dynamic modeling makes it difficult to predict the effects of wear at the design stage for an engine component or a lubricant formulation. The purpose of this discussion is to develop a framework for modeling the formation and evolution of ZDDP antiwear films based on the relevant chemical pathways and physical mechanisms at work.

Six Sigma methodologies in combination with Lean thinking have made considerable inroads as continuous improvement tools initially in manufacturing and more recently for service and transactional processes. There is considerable interest globally in training professionals on the use and application of these tools appropriate to either operational or transactional areas. It has long been realized that adult learning is at its best when participants are involved in relevant “hands-on” experiments. Six Sigma training has seen the use of class room demonstrations ranging from the use of playing cards, simulations and to the use of sophisticated experiments to illustrate concepts of factorial designs. This paper will focus on a series of simple but modular experiments that were developed over the past two years illustrating the application of all the Statistical tools that are taught as a part of Six Sigma Green and Black Belt body of knowledge.

We report on a feasibility study of an optical micro-electro-mechanical systems (MEMS) flow sensor to measure flow rate using Moiré fringe displacement of a floating element. Due to constraints on weight, power, and size for space environmental systems, the development of sensor components that minimize the equivalent systems mass (ESM) while maintaining or exceeding required specifications is highly desirable. A feature of the optical detection method is a physical separation of electrical components from the flow stream. The geometric Moiré fringe shift optically amplifies small displacements by the ratio of the fringe pitch to the movable grating pitch that is detected using an external CCD imager, providing an electrically isolated, robust, direct scheme for detecting flow from shear stress induced displacement.

Two combined four-bar mechanisms have two functions: lift and collapse. In the current design, high effort was found for the collapse function. Axiomatic Design was used to analyze and optimize the current design. The customer domain was mapped into the functional domain by specifying customer needs in terms of functional requirements (FRs) and constraints (Cs). Design parameters (DPs) were identified in the physical domain for each functional requirement. Design matrices were then defined to characterize the product design. The two combined four-bar mechanisms have two functional requirements at the highest level: lift and collapse. The corresponding DPs are: lift four-bar linkage and collapse four-bar linkage. Through zigzagging to decompose to the next level, the design was found to be coupled. At this level, a torsion spring was selected as the DP for minimizing the lift effort.

NASA has long recognized the advantages of providing improved information interfaces to EVA astronauts and has pursued this goal through a number of development programs over the past decade. None of these activities or parallel efforts in industry and academia has so far resulted in the development of an operational system to replace or augment the current extravehicular mobility unit (EMU) Display and Controls Module (DCM) display and cuff checklist. Recent advances in display, communications, and information processing technologies offer exciting new opportunities for EVA information interfaces that can better serve the needs of a variety of NASA missions. Hamilton Sundstrand Space Systems International (HSSSI) has been collaborating with Simon Fraser University and others on the NASA Haughton Mars Project and with researchers at the Massachusetts Institute of Technology (MIT), Boeing, and Symbol Technologies in investigating these possibilities.

The US Air Force (USAF) has evolved a policy for the acquisition of fighter jet engines (FJE). In the 1970s and 1980s that policy placed a premium on FJE performance primarily measured by the metric: thrust/engine weight. In the 1990s, the USAF policy changed from an emphasis on performance to reduced life-cycle cost with a premium on sustainment. This paper reports the results of a study of how the USAF and Corporation Alpha (Alpha) have adapted their processes, practices, and policies to design, develop, manufacture, test, and sustain a family of FJEs. Each member of the family of FJEs is sequentially linked relative to insertion of technology designed to reduce sustainment costs. In addition to the technology linkages, the development of the family of FJEs selected for this case study is also tracked relative to US Department of Defense and USAF policy and industry design, build, and maintain processes, methods, and tools.

The penetration of rainwater through the heating ventilation and air conditioning system (HVAC) of a vehicle directly affects the provision of thermal comfort within the vehicle passenger compartment. Present vehicle designs restrict considerably the air-management processes due to reduced space and tighter packaging. The motivation for the study is to get an insight into factors affecting the water ingress phenomenon when a stationary vehicle is subjected to water loading such as heavy rain when parked or waiting in a traffic light or when in a car wash. The test programme made use of a compact closed circuit full-scale automotive climatic wind tunnel that is able to simulate wind, rain and road inclination. The tunnel was developed as part of the collaborative research between the Flow Diagnostics Laboratory (FDL) of the University of Nottingham and Visteon Climate Control Systems [1].

Many vehicle-dynamics models exist to study the motion of a vehicle. Most of these models fall into one of two categories: very simple models for basic analyses and high-order models consisting of many degrees-of-freedom. For many scenarios, the simple models are not adequate. At the same time, for many vehicle handling and braking studies, the high-order models are more complex than necessary. This paper presents a model that includes the dynamics that are relevant to studying vehicle handling and braking, but is still simple enough to run in near real-time. The model was implemented in such a way that it is easily customized for a particular study. Predictions from this simplified model were compared against a high-order model and against actual vehicle test data. The simulations indicate a close agreement in the results.

A closed loop full-scale automotive climatic wind tunnel is described. The tunnel simulates wind and rain as well as several road conditions. It generates under controlled heat loading, wind speeds of up to 50kmh with different approach boundary conditions, rains from drizzle to cloudburst and road inclines up to 15° in any direction. The design and optimization process of the tunnel functions is outlined and examples of its use in vehicle development are given. The size constraint and the need for a compact design are important features of the tunnel. The tunnel provides an important test bed for close scrutiny of the relationship between rain ingress, vehicle speed, road condition, heat loading and vehicle geometry. The tunnel can also be used to study vehicle thermal management, vehicle thermal comfort, engine cold starting, and wipers efficiency in sever cold weather.

A design framework based on the principles of lean manufacturing and axiomatic design was used as a guideline for designing an automotive component manufacturing system. A brief overview of this design decomposition is given to review its structure and usefulness. Examples are examined to demonstrate how this design framework was applied to the design of a gear manufacturing system. These examples demonstrate the impact that low-level design decisions can have on high-level system objectives and the need for a systems-thinking approach in manufacturing system design. Results are presented to show the estimated performance improvements resulting from the new system design.

The linked cell system gives both reduced cost and volume flexibility. The characteristics of the linked cell system are a consequence of decoupling the operators from the machines, using standard work in process between the cells and by integrating the information system with the cell and system design. By decoupling the operators from the machines the capacity can be increased/decreased in small increments by using more or fewer operators in the cell. The information system is integrated with the linked cell design by the use of a Heijunka box. The Heijunka is used to level production and to initiate the pace of production as a result of pulling withdrawal kanban at a standard time interval. This standard time interval is called the pitch of production. The kanban cards give information about what to produce, when to produce, when to make changeovers but they also give information to control the material replenishment.

This paper provides a technical overview of the components contained in an automotive DVD system. Discussions are limited to present in-vehicle applications of DVD-Video, DVD-ROM and DVD-Audio. Future papers will present the environmental operating requirements.

Two critical milestones that must be achieved during concept design are 1) definition of a product architecture that meets performance, producibility, and strategic objectives, and 2) estimation of the integration risk in each candidate concept. This paper addresses these issues by describing the role played by the producibility members of an Integrated Product Team (IPT) during concept design. Our focus is on the execution of the what we call the “chain method”, which illustrates the structure of function delivery in a concept in a simple pictorial way and helps the IPT to understand the advantages or disadvantages of using a modular or an integral product architecture. The producibility members play a central role in capturing and evaluating the chains for different candidate concepts and decompositions.

The scratch resistance of automotive plastic coatings has been studied extensively over the past few years. Most testing methodology to correlate damage of the coating to field conditions has been in the form of small particulate wearing, e.g., alumina oxide abrasive, or indentation resistance of the coating to an external probe, e.g., a nanoindentation device. The subsequent damage imparted to the coating has generally been analyzed by the amount of coating mass lost in the wear event or through a ratio of optical reflectance of the damaged area to the undamaged surface. In this paper, we attempt to delineate surface damage resistance of several automotive clearcoats through an optical interferometry methodology developed to measure volume and depth of damage incurred with small particle alumina oxide erodents in a simulated wear environment.

A sampling system was developed to measure the evolution of the speciated hydrocarbon emissions from a single-cylinder SI engine in a simulated starting and warm-up procedure. A sequence of exhaust samples was drawn and stored for gas chromatograph analysis. The individual sampling aperture was set at 0.13 s which corresponds to ∼ 1 cycle at 900 rpm. The positions of the apertures (in time) were controlled by a computer and were spaced appropriately to capture the warm-up process. The time resolution was of the order of 1 to 2 cycles (at 900 rpm). Results for four different fuels are reported: n-pentane/iso-octane mixture at volume ratio of 20/80 to study the effect of a light fuel component in the mixture; n-decane/iso-octane mixture at 10/90 to study the effect of a heavy fuel component in the mixture; m-xylene and iso-octane at 25/75 to study the effect of an aromatics in the mixture; and a calibration gasoline.

Enhanced information management techniques made available through emerging Information Technology platforms hold a promise of providing significant improvements in both the effectiveness and efficiency of developing complex products. Determining actual management implementations that deliver on this promise has often proven elusive. Work in conjunction with the Lean Aircraft Initiative at MIT has revealed a straight forward use of Information Technology that portends significant cost reductions. By integrating previously separate types of data involved in the process of product development, engineers and designers can make decisions that will significantly reduce ultimate costs. Since the results presented are not specific to particular technologies or manufacturing processes, the conclusions are broadly applicable.

In this paper we investigate the optimal forming of conical cups of AL 2008-T4 through the use of real-time process control. We consider a flat, frictional binder the force of which can be determined precisely through closed-loop control. Initially the force is held constant throughout the forming of the cup, and various levels of force are tested experimentally and with numerical simulation. Excellent agreement between experiment and simulation is observed. The effects of binder force on cup shape, thickness distribution, failure mode and cup failure height are investigated, and an “optimal” constant binder force is determined. For this optimal case, the corresponding punch force is recorded as a function of punch displacement and is used in subsequent closed-loop control experiments. In addition to the constant force test, a trial variable binder force test was performed to extend the failure height beyond that obtained using the “optimal” constant force level.

Measurements were made of exhaust histories of the following species: unburned hydrocarbons (HC), carbon monoxide, carbon dioxide, oxygen, and nitric oxide (NO). The measurements show that the exhaust flow can be divided into two distinct phases: a leading gas low in HC and high in NO followed by a trailing gas high in HC and low in NO. Calculations of time resolved equivalence ratio throughout the exhaust process show no evidence of a stratified combustion. The exhaust mass flow rate is time resolved by forcing the flow to be locally quasi-steady at an orifice placed in the exhaust pipe. The results with the quasi-steady assumption are shown to be consistent with the measurements. Predictions are made of time resolved mass flow rate which compare favorably to the experimental data base. The composition and flow histories provide sufficient information to calculate the time resolved flow rates of the individual species measured.