Search Results

This paper describes the calculative verification of the effect of the right-and-left torque vectoring system in various types of drivetrain, namely, the front wheels only, the rear wheels only, and both front and rear wheels in FWD, RWD, and AWD vehicles. The effect is evaluated by calculating the vehicle dynamics limit; maximum acceleration and cornering ability. The right-and-left vectoring torque, which is needed for expanding the vehicle dynamics limit, is also calculated. And finally, the paper evaluates the suitable wheels for which the system should be applied in each drivetrain. The application to the front wheels is more effective for FWD vehicles. On the other hand, the application to the rear wheels is more effective for RWD and AWD vehicles.

This paper presents a new torque distribution system-“Right/Left Torque Control System”, aimed at improving a vehicle's cornering properties by using yaw moment control. The torque transfer mechanisms of this system have been analyzed. Also, a yaw moment control algorithm using yaw rate feedback control has been designed. Next, vehicle cornering properties were evaluated using numerical simulation developed from data taken from an actual vehicle. As a result, improvements were achieved in the maneuverability and stability of a vehicle during cornering.

From the standpoint of safety, the demands are growing in recent years for better controllability and stability of automobiles and in particular in trucks. The truck, however, when compared with the passenger car, is subject to larger changes in gross vehicle mass and center of gravity depending on its load placement. In addition, since the cornering power generated by the truck tire per load is smaller than that generated by the passenger car tire, it is difficult to introduce significant improvements in controllability and stability simply by use of passive techniques like suspension characteristic tuning. Therefore, studies were performed on the applicability of the 4WS system, an active vehicle dynamic characteristic control technique, to a Truck as a means for solving these problems.

Aerodynamic drag reduction is one of the most important aspects of enhancing overall vehicle performance. Many car manufacturers have been working to establish drag reduction techniques. This paper describes the development process of a new small speciality car which achieved coefficient of drag(CD) of 0.25. A description of the test facilities and the systems used for developing the aerodynamic aspect of the car are also introduced briefly.

This paper concerns driver's burden for visual information processing in which his central vision is coupled with his peripheral one. A visual driving simulator was applied to the first step of the study, where driver's responses to both central and peripheral tasks were simultaneously investigated. The series of test indicate that the driver's responsiveness to the central and peripheral tasks could define the whole burden for visual information processing. Therefore, it appears that the responsiveness to the peripheral vision could be more or less compromised to support the central one.

This paper describes the results of the study and research on ovate wire helical springs which have been jointly conducted by the members of the Japan Society for Spring Research consisting of the engineers from material suppliers, wire and spring producers and automotive manufacturers as well as researchers at Japanese universities. Attention is focused particularly on two types of wire cross sections, typical elliptical shape and Fuchs' egg-shape. Stresses on these two cross sections were analyzed by numerical calculations within the range of practical specification, and then the results have been compared with those of round wire spring. As a result, it has been found that the elliptical wire spring is superior to Fuchs- egg-shaped one for general application. Simple designing methods for the both types of wire helical springs have been developed based on the findings from the stress analysis.

A high-performance road profile measuring system has developed. The measuring system consists of four laser displacement sensors and an optical speed sensor. It has the advantage of making high-accuracy measurements during a regular run, on a public road, and without any traffic restriction. The measurement is hardly affected by bouncing and pitching motions of the vehicle. The four displacement sensors are arranged at unequal intervals in the direction of vehicle. A road profile is calculated from sensor outputs. This paper describes not only the development of this unique measuring system but also its application to a vehicle behavior. Significant measurements of typical and peculiar public roads in Japan and Northern Europe by the measuring vehicle have been performed for the last few years. The features of these roads are described by the power spectrum densities and the profiles.

One of the leading causes of traffic accidents is the reduction of driver's arousal level. Only a driver with an appropriate arousal level can drive an automobile properly. The purpose of this research is to find the possibility of quantifying the reduction of this arousal level. Two methods are used to quantify the reduction in arousal level: one is related to the driver's behavior, and the other is related to his physiological status. The characteristics of controlling the steering wheel are used as indicators of the driver's behavior, which represents the status of information processing in the brain. The variation of heart rate is used as an indicator of physiological status, which could directly represent arousal level related to drowsiness. Eight male and two female drivers participate both in on-the-road tests for the characteristics of controlling the steering wheel and in a test with a driving simulator for the heart rate variation.

Various parameters for the shift scheduling of an automatic transmission were examined to detect more accurate road conditions, vehicle running conditions, and the driver's intention. The parameters include the vehicle speed, the gradient of a road, an index to curves in the road, and so on. The fuzzy logic was employed to incorporate these parameters into the shift scheduling control. The vehicle running tests have shown that the use of many parameters and the fuzzy logic was effective on reducing the frequencies of the transmission gear shift and the driver's brake operation in such road conditions as usually seen in mountainous areas

In order to meet increasing demands for safety and comfort in a vehicle compartment, automatic adjustment of seat, mirrors, steering wheel has been developed. The multiplex wiring system was constructed for the automatic adjustment of the cockpit elements to drivers preferred positions or to physique-matched settings based on ergonomic data. This paper describes the construction of the multiplex system and functions of automatic adjustment of the cockpit elements for comfortable driving position and better visibility.

A Vehicle Vibration Control System by Active Control has been developed. The experimental results using a 4-cylinder gasoline engine installed in a car showed that at the position of the driver's seat, the acceleration of the vibration was reduced by 16 dB. This system operates stably and at low cost because of having a feedforward system, so many applications can be expected in the near future as methods for vehicle vibration reduction.