Search Results

A development project for a hydrogen internal combustion engine (ICE) system for trucks supporting Japanese freightage has been promoted as a candidate for use in future vehicles that meet ultra-low emission and anti-global warming targets. This project aims to develop a hydrogen ICE truck that can handle the same freight as existing trucks. The core development technologies for this project are a direct-injection (DI) hydrogen ICE system and a liquid hydrogen tank system which has a liquid hydrogen pump built-in. In the first phase of the project, efforts were made to develop the DI hydrogen ICE system. Over the past three years, the following results have been obtained: A high-pressure hydrogen gas direct injector developed for this project was applied to a single-cylinder hydrogen ICE and the indicated mean effective pressure (IMEP) corresponding to a power output of 147 kW in a 6-cylinder hydrogen ICE was confirmed.

This study examined a method of predicting the piston temperature in reciprocating internal combustion engines with the aim of developing lightweight pistons. Since the piston temperature is strongly affected by the in-cylinder temperature distribution and turbulence, it is necessary to consider the effects of flame propagation, cooling by the intake air, temperature rise due to combustion, in-cylinder flow and the combustion chamber shape. A three-dimensional combustion simulation that can take these effects into consideration was run to calculate the heat transfer coefficient from the piston crown surface and the gas temperature. The results were used as the boundary conditions for an analysis of heat transfer from the piston, and a method was thus developed for analyzing the piston temperature.

It is well known that lubricating oil consumption (LOC) is much affected by the cylinder bore deformation occurring within internal combustion engines. There are few analytical reports, however, of this relationship within internal combustion engines in operation. This study was aimed at clarifying the relationship between cylinder bore deformation and LOC, using a conventional in-line four-cylinder gasoline engine. The rotary piston method developed by the author et al. was used to measure the cylinder bore deformation of the engine’s cylinder #3 and cylinder #4. In addition, the sulfur tracer method was applied to measure LOC of each cylinder. LOC was also measured by changing ring tension with a view to taking up for discussion how piston ring conforms to cylinder, and how such conformability affects LOC. Their measured results were such that the cylinder bore deformation was small in the low engine load area and large in the high engine load area.

It can be said that super sports car has a mission to drive the evolution of cars with optimizing the balance between power and environmental performances and pursuing the ultimate driving performance. Nissan has therefore developed the brand new V6 gasoline twin-turbocharged engine for a new generation of super sports cars. To achieve high environmental as well as high dynamic performance, the V6-cylinder layout was selected for its compact size and lightweight while the twin-turbocharged design was aiming for downsizing. All engine parts were designed to achieve high efficiency, as for example, the plasma-sprayed coating of the bore which improves greatly the cooling performance, or the super-heat resistant steel used for the turbocharger, which improves combustion efficiency. Thanks to this technological advance, top-level properties could be attained for sports cars in terms of fuel economy and emissions.

This paper deals with the friction performance results for various new concept piston skirt profiles. The program was conducted under the assumption that friction performance varies by the total amount of oil available at each crank angle in each stroke and the instantaneous distribution of the oil film over the piston skirt area. In previous papers [1,2] it was that lower friction designs would be expected to show higher skirt slap noise. This paper discusses the correlation between friction and skirt slap for each new concept profile design. Finally, this paper explains the friction reduction mechanism for the test samples for each stroke of the engine cycle by observing the skirt movement and oil lubrication pattern using a visualization engine.

A new variable valve event and lift (VVEL) system has been developed by applying a multiple-link mechanism. This VVEL system can continuously vary the valve event angle and lift over a wide range from an exceptional small event angle and small lift and to a large event angle and large lift. This capability offers the potential to improve fuel economy, power output, emissions and other parameters of engine performance. The valve lift characteristics obtained with the VVEL system consist of a synthesis of the oscillatory motion characteristics of the multiple-link mechanism and the oscillating cam profile. With the multiple-link mechanism, the angular velocity of the oscillating cams varies during valve lift, but the valve lift characteristics incorporate both gentle ramp sections and sharp lift sections, the same as a conventional engine.

The purpose of this study is to clarify the state of heat loss to the cylinder liner of the tested engine of which piston and cylinder head were previously measured. The authors' group developed an original measurement technique of instantaneous surface temperature at the cylinder liner wall using thin-film thermocouples. The temperature was measured at 36 points in total. The instantaneous heat flux was calculated by heat transfer analysis using measurement results of the temperature at the wall. As a result, the heat loss ratio to all combustion chamber walls is evaluated except the intake and exhaust valves.

Using small thin-film pressure sensors deposited onto a piston skirt surface, oil-film pressure on the piston skirt surface is measured when piston slap noise is generated without affecting the surface geometry, stiffness and mass of the piston. Under a no-load firing engine condition and at low temperature, the measured oil-film pressure corresponded well to the measured acceleration of the cylinder liner, which is indicative of piston slap noise, confirming the validity of the present method. Moreover, the oil-film pressure distribution on the skirt surface was measured for different engine speeds and piston pin offsets, which enabled more insight to be provided into piston secondary motion than that by considering the effects of cylinder liner acceleration.

An analytical method is presented in this paper for simulating piston secondary dynamics and piston-bore contact for an asymmetric half piston model including elastohydrodynamic (EHD) lubrication at the bore-skirt interface. A piston EHD analysis is used based on a finite-difference formulation. The oil film is discretized using a two-dimensional mesh. For improved computational efficiency without loss of accuracy, the Reynolds’ equation is solved using a perturbation approach which utilizes an “influence zone” concept, and a successive over-relaxation solver. The analysis includes several important physical attributes such as bore distortion effects due to mechanical and thermal deformation, inertia loading and piston barrelity and ovality. A Newmark-Beta time integration scheme combined with a Newton-Raphson linearization, calculates the piston secondary motion.

This paper introduces a new hypereutectic aluminum alloy for piston casting, an improved casting process and a new re-melting procedure. The resulting microstructures improve the fatigue performance of the piston combustion bowl region exposed to severe cyclic thermal and mechanical loading in modern diesel engine applications. It is shown how composition and material properties of the new alloy increase the material's fundamental properties, compared to an existing hypereutectic alloy. The new casting process minimizes the occurrence of fine oxide inclusions which helps to exploit the fundamental material strength. Finally the paper describes the combustion bowl re-melting process and gives engine validation results to illustrate its considerable influence on premature fatigue failure.

Due to increasing economic and environmental performance requirements of internal combustion engines, piston manufacturers now focus more on lower friction designs. One factor strongly influencing the friction behavior of pistons is the dynamic interaction between lubricating oil, cylinder bore and piston. Therefore, the dynamic effect of the oil film in the gap between the liner and piston has been studied, using a single cylinder engine equipped with a sapphire window. This single cylinder engine was also equipped with a floating liner, enabling real-time friction measurement, and directly linking the oil film behavior to friction performance of pistons.

The engineering of an improved performance PTFE crankshaft (IPPC) seal is a challenge in the pursuit of longer service life and reduced total cost of ownership in the vehicular industry. This paper briefly reviews from the authors’ perspective the evolution of laydown PTFE seal design and details the IPPC seal features along with bench testing performance data.

Hydrogen is expected to be a clean and energy-efficient fuel for the next generation of power sources because it is CO2-free and has excellent combustion characteristics. In this study, an attempt was made to apply Homogeneous Charge Compression Ignition (HCCI) combustion to hydrogen with the aim of achieving low oxides of nitrogen (NOx) emissions and high fuel economy with the assistance of the di-methyl-ether (DME) fuel supplement. As a result, HCCI combustion of hydrogen mixed with 25 vol% DME achieved approximately a 30% improvement in fuel economy compared with HCCI of pure DME and spark-ignited lean-burn combustion of pure hydrogen under almost zero NOx emissions and low hydrocarbon (HC) emissions. This is attributed to control of the combustion process to attain the optimum onset of combustion and to a reduction of cooling losses.

The interest in using combustion pressure in engine control systems has initiated development activities to integrate pressure sensors into existing engine components. Since cylinder head gasket contacts the combustion chamber of multiple cylinders, the ability to add pressure-sensing capability is of unique interest. Two viable multi-layer steel cylinder head gasket design approaches have been developed to fulfill this interest. These designs offer the full sealing performance of traditional multi-layer steel designs, but also include accurate pressure sensors packaged in a total gasket thickness realistic to modern engines.

The objective was to rank piston friction and noise for three piston architectures at three cold clearance conditions. Piston secondary motion was measured using four gap sensors mounted on each piston skirt to better understand the friction and noise results. One noticeable difference in friction performance from conventional designs was as engine speed increased the friction force during the expansion stroke decreased. This was accompanied by relatively small increases in friction force during the other strokes so Friction Mean Effective Pressure (FMEP) for the whole cycle was reduced. Taguchi's Design of Experiment method was used to analyze the variances in friction and noise.

Lead is well recognized as having environmental and health risks. The elimination of lead from automotive components has been accelerated by the European End of Life Directive as well as litigation concerns in the U.S. In response to these circumstances, two new lead-free bronze materials have been developed as replacements for SAE 792 (CuSn10Pb10). The two lead free materials are sintered bronzes with nominal compositions CuSn10Bi3 and CuSn8Ni. The characteristics and performance of these materials are compared and contrasted to sintered and cast SAE 792. Fatigue strength, mechanical properties, corrosion resistance, and wear resistance are described and related to the microstructural and application conditions. The CuSn10Bi3 material is preferred for SAE 792 applications having poor lubrication or high-speed conditions, typically in spark ignition connecting rod bushings or highly loaded transmission bushings.

Ever increasing specific power of diesel engines has put huge demand on effective thermal management of the pistons for the desired reliability and durability. The piston temperature control is commonly achieved by injecting cooling oil into piston galleries, but the design of the cooling system as well as the boundary conditions used in FEA simulations have so far relied mostly on empirical methods. A numerical procedure using 3D computational fluid dynamics (CFD) has therefore been developed to simulate the cooling process and to estimate the cooling efficiency of gallery. The model is able to predict the detailed oil flow and heat transfer in gallery, of different designs and engine applications, under dynamic conditions. The resulted spatially resolved heat transfer coefficient from the CFD model, with better accuracy, enables improved prediction of piston temperature in finite element analysis (FEA).

The bores of the cylinder block are usually machined prior to assembly with the cylinder head. In this case, bore distortion occurs when the cylinder block is assembled with the cylinder head due to the load applied by the head bolts and the surface pressure of the head gasket. This bore distortion influences sealing and operating characteristics of the pistons and piston rings, requiring an increase in bore thickness and addition of ribs to obtain higher cylinder block rigidity, which lead to an increase in weight. In order to improve engine performance, it is necessary to control bore distortion more effectively. With the aim of reducing bore distortion when assembled with the cylinder head, the bores are machined with a dummy cylinder head installed on the block to provide an equivalent head bolt load and gasket surface pressure. By using this bore circulatory machining technology, bore distortion after cylinder head assembly can be reliably suppressed.

A finite element human model has been developed to simulate occupant behavior and to estimate injuries in real-world car crashes. The model represents an average adult male of the US population in a driving posture. Physical geometry, mechanical characteristics and joint structures were replicated as precise as possible. The total number of nodes and materials is around 67,000 and 1,000 respectively. Each part of the model was not only validated against human test data in the literature but also for realistic loading conditions. Additional tests were newly conducted to reproduce realistic loading to human subjects. A data set obtained in human volunteer tests was used for validating the neck part. The head-neck kinematics and responses in low-speed rear impacts were compared between the measured and calculated results. The validity of the lower extremity part was examined by comparing the tibia force in a foot impact between the test data and simulation results.

Aiming at the improvement in piston lubrication and the reduction of piston friction loss under this study, piston friction forces of cylinders with different surface roughness and treatment methods have been measured by means of a floating liner method, and the piston surface conditions have been also observed. As a result, it is found that the piston lubrication can be markedly improved by reducing the cylinder surface roughness. It is also verified that the deterioration in lubrication can be reduced even if some low viscosity oil is used, and the effect on the friction loss reduction becomes greater by reducing the piston surface roughness. On the other hand, it is found that many small vertical flaws are generated on the cylinder surface by reducing the surface roughness. In order to cope with this problem, etching and DLC (Diamond Like Carbon) coating have been tested as the surface treatments. As a result, it is confirmed that DLC coating is effective for the above.