Search Results

Modern agriculture has evolved dramatically over the past half century. To be profitable, farms need to significantly increase their crop yields, and thus there are amplified demands on farming equipment. Equipment duty cycles have been raised in scope and duration, as the required output of the agricultural industry to sustain a growing population has stimulated the need for further advances in effective productivity gains on the farm. The mainstay mechanical assistant to the farmer, the tractor, has also evolved with the changes in modern agriculture to meet the requirements of these newer tasks. Larger, more capable vehicles have been introduced to help farmers efficiently meet these demands. At the same time, the current generation of tractor diesel engine lubricants has facilitated high levels of performance in the agricultural equipment market for many years. This is a testament to the role modern lubricants play in productivity in such a critical industry.

To meet increasingly stringent emissions and fuel economy regulations, many Original Equipment Manufacturers (OEMs) have recently developed and deployed small, high power density engines. Turbocharging, coupled with gasoline direct injection (GDI) has enabled a rapid engine downsizing trend. While these turbocharged GDI (TGDI) engines have indeed allowed for better fuel economy in many light duty vehicles, TGDI technology has also led to some unintended consequences. The most notable of these is an abnormal combustion phenomenon known as low speed pre-ignition (LSPI). LSPI is an uncontrolled combustion event that takes place prior to spark ignition, often resulting in knock, and has been known to cause catastrophic engine damage. LSPI propensity depends on a number of factors including engine design, calibration, fuel properties and engine oil formulation. Several engine tests have been developed within the industry to better understand the phenomenon of LSPI.

Gasoline direction injection (GDI) engines have been widely used by light-duty vehicle manufacturers in recent years to meet stringent fuel economy and emissions standards. Particulate Matter (PM) mass emissions from current GDI engines are primarily composed of soot particles or black carbon with a small fraction (15% to 20%) of semi-volatile hydrocarbons generated from unburned/partially burned fuel and lubricating oil. Between 2017 and 2025, PM mass emissions regulations in the USA are expected to become progressively more stringent going down from current level of 6 mg/mile to 1 mg/mile in 2025. As PM emissions are reduced through soot reduction, lubricating oil derived semi-volatile PM is expected to become a bigger fraction of total PM mass emissions.

Specific frictional properties are essential to provide correct and pleasurable shifting in a manual transmission. Synchroniser rings are being manufactured from an increasingly wider range of materials, and it is important to understand synchroniser-additive interactions in order to develop tailored lubricants that provide the desired frictional performance. This paper describes a study of the interaction of various friction modifier additives with a range of synchroniser materials in order to better understand the potential to develop lubricants that provide optimal frictional performance across a wide range of manual transmission-synchroniser systems.

Motorcycle manufacturers have recognized that highly friction modified passenger car oils can be deleterious to clutch performance, leading to clutch slippage. To address this issue, a JASO specification for four-stroke motorcycle oils was developed in 1999, categorizing oils into high friction oils termed JASO MA and low friction oils termed JASO MB. The high friction oils were preferred for most motorcycles where the engine oil also lubricates the clutch and gears. New motorcycle transmission technologies have increased the number of dry clutch applications which has led to an increased demand for JASO MB oils to improve fuel efficiency. While JASO MB oils contain friction modifiers to improve initial fuel economy, the motorcycle specifications have not addressed the fuel economy durability of motorcycle oils.

Specific frictional properties are essential to provide correct and pleasurable shifting in a manual transmission. Synchroniser rings are being manufactured from an increasingly wider range of materials, and so it is important to understand synchroniser-additive interactions in order to develop tailored lubricants that provide the desired frictional performance. This paper describes a study of the interaction of various friction modifier additives with a range of synchroniser materials in order to better understand the potential to develop lubricants that provide optimal frictional performance across a wide range of manual transmission-synchroniser systems. This presentation will outline the results of testing fluids with a range of synchroniser materials and will be followed by a future paper that will describe details of the fluids and analysis of their interactions with the different synchroniser surfaces.

Technical impacts on engine oil performance by the use of waste cooking oil as bio-diesel fuel (BDF) are not well understood while the industry has made significant progress in studies on quality specifications and infrastructure. The authors, who consist of a consortium organized by Japan Lubricating Oil Society (JALOS), examined technical effects of waste cooking oil as BDF on engine oil performance such as wear and high temperature corrosion using vehicle fleets and bench tests to identify technical issues of engine oil meeting the use of BDF. The study brings fundamental information about technical impacts of BDF on engine oils.

Requirements to reduce emissions and improve vehicle fuel economy continue to increase, spurred on by agreements such as the Kyoto Protocol. Lubricants can play a role in improving fuel economy, as evidenced by the rise in the number of engine oil specifications worldwide that require fuel economy improvements. A novel friction modifier technology has been developed to further improve vehicle fuel economy. The development of this novel friction modifier technology which contains only N,O,C,H was previously published along with the initial demonstration of performance in motorized Toyota engines. In order to validate this performance in fired engine tests, oil was evaluated in a Toyota Corolla Fielder with a 1500 cc gasoline engine. Testing was conducted in the Japanese 10-15 and JC08 modes, as well as the European EC mode, and the US FTP mode.

Prior work by various OEMs has identified the ability of phosphorus-containing compounds to interfere with the efficiency of modern emissions control systems utilized by gasoline-powered vehicles. Considering the growing societal concerns about ecological effects of exhaust emissions, greenhouse gas emissions and related global climatic changes, it becomes desirable to examine the effect of reduced phosphorous (P) deposits in various vehicle makes, models and types of service, over the lifetime of a vehicle's operation. This paper assesses advantages and disadvantages of various methods to examine the path of P transfer throughout exhaust catalytic systems. Test types discussed include examples of bench testing focusing on catalyst compatibility, dyno mileage accumulation and field trial examinations.

Since construction machinery manufacturers recommend various brands and types of greases for their machinery, customers would benefit from a standardized grease which can be used in all construction machinery. Furthermore, construction machinery manufacturers have many experiences of field problems caused by commercially available and commonly used EP Lithium greases. Therefore, the Fuels and Lubricants Committee of Japan Construction Mechanization Association (JCMA) has developed a new grease specification called “Japan Construction Mechanization Association Specification (JCMAS) GK,” for construction equipment. The JCMAS GK includes requirements for National Lubrication and Grease Institute (NLGI) No. 1 and No. 2 consistency grades. The JCMAS GK greases have enough lubricating properties for periodical grease fitting of most construction machines, hydraulic excavators, bulldozers and wheel loaders. The JCMAS GK greases are applicable from -20 to +130 degrees Celsius.

Hydraulic fluid (HF) specifications for mobile construction equipment called JCMAS HK and HKB have been established by the Fuels and Lubricants Committee of Japan Construction Mechanization Association (JCMA). The specifications are designated by two viscosity categories of single grade and multigrade. Each category has ISO viscosity grade (VG) 32 and 46. The JCMAS HK oils are recommended for use in hydraulic systems designed at pressure up to 34.3MPa(5000psi) and to heat hydraulic fluid up to 100 °C. These oils also provide wear control, friction performance, oxidation and rust protection, seal swell control and filterability performance. Two piston pump test procedures were developed to evaluate lubricating performance of these oils under high pressure conditions. The JACMAS HKB oils are classified as environmentally friendly oils due to the additional requirement for biodegradability.

A discriminating dynamometer-based test was developed for evaluating cold start and warmup engine performance based on in-cylinder pressure measurements. The dynamometer test offers advantages in time required, flexibility and reduced variability over the vehicle procedure on which it was based. A parametric study on fuel driveability index (DI), ethanol content and intake valve deposit (IVD) rating demonstrated that each of these parameters had a statistically significant impact on engine cold start performance. Simple numerical offsets to fitted models based on oxygen content of the fuel did not account for the difference in engine performance of hydrocarbon-only versus ethanol-containing fuels. The effect of IVD on engine performance did not appear to depend on the DI of the fuel. The benefits of cleaner valves are seen even in fuels of very low DI.

The lubricant is a key component in the successful operation of a manual transmission, but it is important that the interactive effects with the friction material are understood. This paper examines the effect of several key additive components on the friction and wear performance of a single sinter composition in a carefully controlled laboratory test. In addition, the test method allows one to develop information about the shift behavior of the fluid-synchronizer material combination which provides useful information about shift quality. From the original experimental design program a predictive model was developed and an optimized formulation was tested as a validation of the results.

Extended drain of axle and transmission lubricants has gained wide acceptance in both passenger car and commercial vehicle applications. Understanding how the lubricant changes during extended drain operations is crucial in determining appropriate lubricants and drain intervals for these applications. A suitable aging screen test with an established relationship to field performance is essential. Over the years numerous methods have been studied (DKA, GFC, ISOT, ASTM L-60) with varying degrees of success1,2,3. Current methods tend to be overly severe in comparison to field experience, hence the need for further work in this area. As a result of recent work, a lubricant aging test method has been developed which shows good correlation with field experience, giving us an effective tool in the development of long drain oils.

Water-emulsified diesel fuel technology has been proven to reduce nitrogen oxides (NOx) and particulate matter (PM) simultaneously at relatively low cost compared to other pollution-reducing strategies. The value of this technology is that it requires absolutely no engine adjustments or modifications to reduce harmful emissions. Technologies that break the NOx -particulate trade-off are virtually non-existent, therefore understanding how the water contained in an emulsified fuel can reduce both NOx and PM simultaneously is critical. To understand this phenomenon, emulsified fuels with varying water levels (0 to 20%) were evaluated in a multi-cylinder marine engine using three different injection timings. This testing in an actual engine confirms that as the water level is increased the amount of NOx and PM are reduced without compromising engine performance.

The relationship between 76 Racing and NASCAR allowed 76 Lubricants Company to work closely with Richard Childress Racing (RCR) and The Lubrizol Corporation in the development of oil screening and analytical test procedures which permit rapid evaluation of potential top-tier NASCAR race oils. The oils were designed to meet the challenge of increasingly severe engine operating parameters. This paper will discuss dynamometer testing and how properties of the oil such as viscosity grade, base fluid, and additives affect engine durability in the dynamometer test program and performance at the track in NASCAR Winston Cup Racing. Areas of growing concern include the cam/lifter contact, ring/liner contact, wrist pin/pin bore and wrist pin bushing contacts. Racing lubricants must withstand these harsh conditions for periods of 3-4 hours of continuous running.

Inconsistent fuel filter life is a problem that continues to plague most heavy-duty diesel fleets. It has been proven that fuel filter life can be strongly influenced by the thermal and oxidative stability of diesel fuel that is being filtered. Filters consistently exposed to diesel fuels that produce a tar-like substance in abundance upon heating (sometimes termed “asphaltenes”) will plug far more rapidly than filters exposed to diesel fuel that does not easily form these tar-like substances. Fuel additives have long been used to maintain fuel system cleanliness and to improve diesel fuel stability. It follows logically that such additives could have a positive impact on fuel filter life by maintaining the cleanliness of the fuel filtration media. This paper reviews the laboratory evaluations and field tests that were run to compare fuel filter life in both the presence and absence of diesel fuel additives.

Driven by global demands for improved fuel economy and reduced emissions, significant improvements have been made to engine designs and control systems, vehicle aerodynamics, and fuel quality. Improvements, such as the continuously slipping torque converter, have also been made to automatic transmissions to increase vehicle efficiency. Recently, belt-continuously variable transmissions (b-CVTs) have been commercialized with the promise of significant fuel economy improvements over conventional automatic transmissions. Automotive traction drive transmissions may soon join belt-CVTs as alternative automatic transmission technology. Much of the information reported in technical and trade publications has been on the mechanics of these traction drive systems. As automotive traction drives move closer to commercial reality, more attention must be given to the performance requirements of the automotive traction fluid.

The intent of industry and OEM factory fill oil specifications is to ensure lubricant pumping performance at low temperatures through rheological measurements using the Mini Rotary Viscometer and Scanning Brookfield tests. Often these tests provide conflicting information, yet lubricant formulations must be optimized to meet requirements of both tests. At the root of this issue is how test information is interpreted, since ultimately it is that interpretation that influences how specifications are set. In this paper, we focus on understanding the Scanning Brookfield test's gelation index which is part of ILSAC GF-2 and GF-3 specifications; our objective is to understand what is measured and its relation to meaningful low temperature lubricant performance. We approach this objective by measuring the low temperature rheology of mineral oils and lubricants formulated from these oils.

This work presents a follow-up to previous efforts by the authors to investigate the susceptibility of gasoline direct injection (g-di) engines to deposit formation and the effect of those deposits on vehicle performance. A series of injector keep clean and clean up tests in base and additized fuels utilizing the ASTM D 5598 cycle provided a range of injector fouling levels. It is found that the g-di engine employed here is more susceptible to injector deposits than even the sensitive port fuel injected (PFI) engine used as industry reference in the D 5598 procedure. Injector keep clean and clean up performance of several representative deposit control chemistries are evaluated. In order to determine the effect of injector fouling on performance, emissions and driveability tests are performed on the vehicles at varying levels of injector fouling. Regulated emissions, particulates, fuel consumption and driveability are all shown statistically to be linked to injector fouling.