Search Results

Engine and vehicle tailpipe emissions can be measured in laboratories equipped with engine dynamometers and chassis dynamometers, respectively. In addition to laboratory testing, there is an increase in interest to measure on-road vehicle emissions using portable emissions measurement systems in order to determine real-driving emissions. Current methods to quantify engine, vehicle tailpipe, and real-driving emissions include the raw continuous, dilute continuous, and dilute bag measurement methods. Although the dilute bag measurement method is robust, recent improvements to the raw and dilute continuous measurement methods can account for the time delay between the probe tip and analyzer in addition to gas transport dynamics in order to reliably recover the tailpipe concentration signals. These improvements significantly increase the reliability of results using the raw and dilute continuous measurement methods, making them possible alternatives to the bag method.

Eight whole fresh-frozen cadavers (6 female, 2 male) that were elderly and/or female were laterally impacted using UMTRI's dual-sled side-impact test facility. Cadavers were not excluded on the basis of old age or bone diseases that affect tolerance. A thinly padded, multi-segment impactor was used that independently measured force histories applied to the shoulder, thorax, abdomen, greater trochanter, iliac wing, and femur of each PMHS. Impactor plates were adjusted vertically and laterally toward the subject so that contact with body regions occurred simultaneously and so that each segment contacted the same region on every subject. This configuration minimized the effects of body shape on load sharing between regions. Prior to all tests, cadavers were CT scanned to check for pre-existing skeletal injuries. Cadavers were excluded if they had pre-existing rib fractures or had undergone CPR.

Lateral impact tests were performed using seven male post-mortem human subjects (PMHS) to characterize the force-deflection response of contacted body regions, including the lower abdomen. All tests were performed using a dual-sled, side-impact test facility. A segmented impactor was mounted on a sled that was pneumatically accelerated into a second, initially stationary sled on which a subject was seated facing perpendicular to the direction of impact. Positions of impactor segments were adjusted for each subject so that forces applied to different anatomic regions, including thorax, abdomen, greater trochanter, iliac wing, and thigh, could be independently measured on each PMHS. The impactor contact surfaces were located in the same vertical plane, except that the abdomen plate was offset 5.1 cm towards the subject.

In this study, the performance and emissions of a 4 cylinder 2.5L light-duty diesel engine with methane fumigation in the intake air manifold is studied to simulate a dual fuel conversion kit. Because the engine control unit is optimized to work with only the diesel injection into the cylinder, the addition of methane to the intake disrupts this optimization. The energy from the diesel fuel is replaced with that from the methane by holding the engine load and speed constant as methane is added to the intake air. The pilot injection is fixed and the main injection is varied in increments over 12 crank angle degrees at these conditions to determine the timing that reduces each of the emissions while maintaining combustion performance as measured by the brake thermal efficiency. It is shown that with higher substitution the unburned hydrocarbon (UHC) emissions can increase by up to twenty times. The NOx emissions decrease for all engine conditions, up to 53%.

This paper reviews the field operational test (FOT) methodology adopted in recent years for the evaluation of driver-assistance systems. The Road Departure Crash Warning System program is used both for illustration and as a case study. This project involved an extensive field operational test of a driver-assistance system using volunteers from the general public who drove instrumented research vehicles in place of their normal cars. Objective and subjective data were collected in these trials, and comparisons were made between driving behavior under conditions where the systems were either enabled or disabled. This paper presents sample results from the analyses and draws conclusions on the strengths and weaknesses of the FOT method.

A method has been developed to identify and document the locations of rib fractures from two-dimensional CT images obtained from occupants of crashes investigated in the Crash Injury Research Engineering Network (CIREN). The location of each rib fracture includes the vertical location by rib number (1 through 12), the lateral location by side of the thorax (inboard and outboard), and the circumferential location by five 36-degree segments relative to the sternum and spine. The latter include anterior, anterior-lateral, lateral, posterior-lateral, and posterior regions. 3D reconstructed images of the whole ribcage created from the 2D CT images using Voxar software are used to help identify fractures and their rib number. A geometric method for consistently locating each fracture circumferentially is described.

A single cylinder engine was operated in HCCI mode with diesel-range fuels, spanning a range in cetane number (CN) from 34 to 62. In addition to measurements of standard gaseous emissions (CO, HC, and NOx), multiple sampling and analysis techniques were used to identify and measure the individual exhaust HC species including an array of oxygenated compounds. A new analytical method, using liquid chromatography (LC) with electrospray ionization-mass spectrometry (ESI-MS) in tandem with ultraviolet (UV) detection, was developed to analyze the longer chain aldehydes as well as carboxylic acids. Results showed an abundance of formic and butyric acid formation at or near the same concentration levels as formaldehyde and other aldehydes.

This paper will present emissions durability data from an underground mining vehicle equipped with diesel particulate filter technology, which was followed over 4000 hrs on a Detroit Diesel Series 60 engine. The twin particulate filter system is catalyzed using a base metal formulation on cordierite wall flow monoliths. After the durability accumulation, the recovered filters were individually emissions tested on a Detroit Diesel Series 50 engine over the ISO 8178 test cycle. Performance, maintenance and emissions issues pertaining to base metal catalysts will be discussed.

Dimethyl Ether (DME) is a potential ultra-clean diesel fuel. Its unique characteristics require special handling and accommodation of its low viscosity and low lubricity. In this project, DME was blended with diesel fuel to provide sufficient viscosity and lubricity to permit operation of a 7.3 liter turbodiesel engine in a campus shuttle bus with minimal modification of the fuel injection system. A pressurized fuel delivery system was added to the existing common rail injection system on the engine, allowing the DME-diesel fuel blend to be circulated through the rail at pressures above 200 psig keeping the DME in the liquid state. Fuel exiting the rail is cooled by finned tubed heat exchangers and recirculated to the rail using a gear pump. A modified LPG tank (for use on recreational vehicles) stores the DME- diesel fuel blend onboard the shuttle bus.

Biodiesel fuels are widely known to yield an increase in NOx emissions in many diesel engines. It has been suggested that the increase in NOx is due to injection timing differences caused by the low compressibility of biodiesel. In this work, comparisons of injection timing and duration were performed for diesel fuel and a range of biodiesel blends (B20 to B100). The fuel injector on a 4-stroke, single-cylinder, four horsepower, air-cooled, direct injection diesel engine was positioned in a spray chamber while the engine was motored and fuel was delivered to the injector by the fuel pump on the engine. Spray visualization and quantification of injection timing were performed in the spray chamber using an engine videoscope, light attenuation from a HeNe laser and fuel line pressure, and were synchronized to crank shaft position.

In this study, performance and emissions characteristics of an LPG direct injection (DI) engine with a rotary distributor pump were examined by using cetane enhanced LPG fuel developed for diesel engines. Results showed that stable engine operation was possible for a wide range of engine loads. Also, engine output power with cetane enhanced LPG was comparable to diesel fuel operation. Exhaust emissions measurements showed NOx and smoke could be reduced with the cetane enhanced LPG fuel. Experimental model vehicle with an in-line plunger pump has received its license plate in June 2000 and started high-speed tests on a test course. It has already been operated more than 15,000 km without any major failure. Another, experimental model vehicle with a rotary distributor pump was developed and received its license plate to operate on public roads.

Effective application of human figure models to truck interior design requires accurate data on the postures and positions of truck drivers. Errors in positioning of figure models propagate to errors in reach, visibility, and other analyses. This paper describes methods used in a recent study to measure in-vehicle driving postures in Class 6, 7, and 8 trucks. A three-dimensional coordinate measurement machine was used to measure body landmark locations after a driver completed a short road course. The data were used to validate posture-prediction models developed in a previous laboratory study. Vehicle calibration, driver selection, and testing methods are reviewed.

Several oxygenates have been proposed and tested for use with diesel fuel as a means of reducing exhaust emissions. This paper examines dimethyl ether (DME), which can be produced in many ways including via Air Products and Chemicals, Inc's Liquid Phase Technology (LPDME ™). Modest additions of DME into diesel fuel (2 wt.% oxygen) showed reductions in particulate matter emissions, but the previous data reported by the author from a multicylinder Navistar 7.3L Turbodiesel engine were scattered. In this study, experiments were performed on a multi-cylinder Navistar 7.3L Turbodiesel engine to repeatably confirm and extend the observations from the earlier studies. This is an important step in not only showing that the fuel does perform well in an engine with minor modifications to the fuel system, but also showing that DME can give consistent, significant results in lowering emissions.

Current specifications for automatic-transmission fluids and gear oils have viscosity limits which are determined by ASTM D 2983. However, that test is plagued by poor precision. This paper describes the development of a method using the Mini-Rotary Viscometer to make the determination of apparent viscosity at the same nominal shear stress as ASTM D 2983. In this test procedure, samples are cooled in a manner similar to that described in ASTM D 2983. Experimental data were obtained on a mixture of 17 automatic-transmission and gear-oil fluids that included a number of different formulation strategies and commercial products. The results of this method yield a nearly one to one correlation with the results determined by ASTM D 2983.

Two new techniques for investigating the thermal skin-burn potential of airbags are presented. A reduced-volume airbag test procedure has been developed to obtain airbag pressures that are representative of a dynamic ridedown event during a static deployment. Temperature and heat flux measurements made with this procedure can be used to predict airbag thermal burn potential. Measurements from the reduced-volume procedure are complemented by data obtained using two gas-jet simulators, called heatguns. Gas is vented in controlled bursts from a large, heated, pressurized tank of gas onto a target surface. Heat flux measurements on the target surface have been used to develop quantitative models of the relationships between gas jet characteristics and burn potential.

The tests described here have been used to provide a preliminary checkout of the control functionality of a prototype adaptive cruise control (ACC) system being used in a field operational test of intelligent cruise control. The results presented provide an initial characterization of the headway control performance of the ACC system. The inputs to these tests are the speed of the preceding vehicle. The results of the tests are based upon measurements of range, range rate, velocity, transmission shift commands, and velocity commands resident within the ACC system. Numerical performance measures are derived from these data and used to characterize system performance quantitatively. Results from these types of tests could be used in assessing differences in headway control characteristics associated with various ACC systems.

Dynamic seat-position testing conducted recently at UMTRI on several different vehicles indicates that, in many cases, the current seating accommodation model represented in SAE J1517 does not accurately predict the distribution of driver seat positions. In general, J1517 tends to predict population percentile seat positions that are forward of observed percentile seat positions, and differences can be as much as 60 mm. It was hypothesized that vehicle factors other than seat height can have substantial and independent effects on driver seat position. The effects of steering-wheel position, seat height, seat-cushion angle, and transmission type on driver fore/aft seat position are being investigated, and results are being used to develop a new driver seating accommodation model called SAM.

Tilt-table testing is one means of quantifying the static roll stability of highway vehicles. By this technique, a test vehicle is subjected to a physical situation analogous to that experienced in a steady state turn. Although the analogy is not perfect, the simplicity and fidelity of the method make it an attractive means for estimating static rollover threshold. The NHTSA has suggested the tilt-table method as one means of regulating the roll stability properties of light trucks and utility vehicles. One consideration in evaluating the suitability of any test method for regulatory use is repeatability, both within and among testing facilities. As a first step toward evaluating the repeatability of the tilt-table method, an experimental study examining the sensitivity of tilt-table test results to variables associated with methodology and facility was conducted by UMTRI for the Motor Vehicle Manufacturers Association. This paper reports some of the findings of that study.

In recent investigations of airbag deployments, drivers h v c reported abrasions to the face, neck, and forearms due to deploying airbags, A study of the airbag design and deployments parameters affecting the incidence and severity of abrasions caused by driver-side airbags has led to the development of a laboratory test procedure to evaluate the potential of an airbag design m cause skin injury This report describes the procedure, which is based an static deployments of airbags into a cylindrical lest fixture. The target area is covered with a material that responds to abrasion-producing events in a manner related to human skin tolerance. Test results show excellent correlation with abrasion injuries produced by airbag deployments into the skin of human volunteers.

Several synthetic fuels derived from shale and coal were evaluated with respect to a reference petroleum-based Diesel fuel. Tests conducted using a single-cylinder DI Diesel engine were designed to quantitatively compare the fuels on the basis of performance, combustion characteristics, gas-phase emissions, particulate emissions, and biological activity of the solid phase soluble organic fraction. The biological activity was assessed using the Ames Salmonella typhimurium test. The shale fuels studied were a Paraho marine Diesel fuel and a light shale oil condensate from the Logan Wash in situ retorting operation. The coal liquids, Solvent Refined Coal-II and Exxon Donor Solvent, could not be run neat; therefore, they were blended 20% and 40% by volume with the certified DF-2 baseline fuel. Of the synthetic fuels tested, only the Paraho marine Diesel fuel exhibited the qualities of a good finished Diesel fuel.