Search Results

There is an increasing interest in transient thermal simulations of automotive brake systems. This paper presents a high-fidelity CFD tool for modeling complete braking cycles including both the deceleration and acceleration phases. During braking, this model applies the frictional heat at the interface on the contacting rotor and pad surfaces. Based on the conductive heat fluxes within the surrounding parts, the solver divides the frictional heat into energy fluxes entering the solid volumes of the rotor and the pad. The convective heat transfer between the surfaces of solid parts and the cooling airflow is simulated through conjugate heat transfer, and the discrete ordinates model captures the radiative heat exchange between solid surfaces. It is found that modeling the rotor rotation using the sliding mesh approach provides more realistic results than those obtained with the Multiple Reference Frames method.

Contamination protection of brake rotors has been a challenge for the auto industry for a long time. As contamination of a rotor causes corrosion, and that in turn causes many issues like pulsation and excessive wear of rotors and linings, a rotor splash protection shield became a common part for most vehicles. While the rotor splash shield provides contamination protection for the brake rotor, it makes brake cooling performance worse because it blocks air reaching the brake rotor. Therefore, balancing between contamination protection and enabling brake cooling has become a key critical factor when the splash shield is designed. Although the analysis capability of brake cooling performance has become quite reliable, due to lack of technology to predict contamination patterns, the design of the splash protection shield has relied on engineering judgment and/or vehicle tests. Optimization opportunities were restricted by cost and time associated with vehicle tests.

We propose a composite thermal model of the vehicle passenger compartment that can be used to predict and analyze thermal comfort of the occupants of a vehicle. Physical model is developed using heat flow in and out of the passenger compartment space, comprised of glasses, roof, seats, dashboard, etc. Use of a model under a wide variety of test conditions have shown high sensitivity of compartment air temperature to changes in the outside air temperature, solar heat load, temperature and mass flow of duct outlet air from the climate control system of a vehicle. Use of this model has subsequently reduced empiricism and extensive experimental tests for design and tuning of the automatic climate control system. Simulation of the model allowed several changes to the designs well before the prototype hardware is available.

Misfire diagnostics are required to detect missed combustion events which may cause an increase in emissions and a reduction in performance and fuel economy. If the misfire detection system is based on crankshaft speed measurement, driveline torque variations due to rough road can hinder the diagnosis of misfire. A common method of rough road detection uses the ABS (Anti-Lock Braking System) module to process wheel speed sensor data. This leads to multiple integration issues including complexities in interacting with multiple suppliers, inapplicability in certain markets and lower reliability of wheel speed sensors. This paper describes novel rough road detection concepts based on signal processing and statistical analysis without using wheel speed sensors. These include engine crankshaft and Transmission Output Speed (TOS) sensing information. Algorithms that combine adaptive signal processing and specific statistical analysis of this information are presented.

Finite element analysis (FEA) predictions of magnesium beams are compared to load versus displacement test measurements. The beams are made from AM60B die castings, AM30 extrusions and AZ31 sheet. The sheet and die cast beams are built up from two top hat sections joined with toughened epoxy adhesive and structural rivets. LS-DYNA material model MAT_124 predicts the magnesium behavior over a range of strain rates and accommodates different responses in tension and compression. Material test results and FEA experience set the strain to failure limits in the FEA predictions. The boundary conditions in the FEA models closely mimic the loading and constraint conditions in the component testing. Results from quasi-static four-point bend, quasi-static axial compression and high-speed axial compression tests of magnesium beams show the beam's behavior over a range of loadings and test rates. The magnesium beams exhibit significant material cracking and splitting in all the tests.

Casting, machining and structural simulations were completed on a V8 engine block made in Compacted Graphite Iron (CGI) for use in a racing application. The casting and machining simulations generated maps of predicted tensile strength and residual stress in the block. These strength and stress maps were exported to a finite element structural model of the machined part. Assembly and operating loads were applied, and stresses due to these loads were determined. High cycle fatigue analysis was completed, and three sets of safety factors were calculated using the following conditions: uniform properties and no residual stress, predicted properties and no residual stress, and predicted properties plus residual stress.

This paper describes an effective integrated method for estimation of subject-specific mass, inertia tensor, and center of mass of individual body segments of a digital avatar for use with physics-based digital human modeling simulation environment. One of the main goals of digital human modeling and simulation environments is that a user should be able to change the avatar (from male to female to a child) at any given time. The user should also be able to change the various link dimensions, like lengths of upper and lower arms, lengths of upper and lower legs, etc. These customizations in digital avatar's geometry change the kinematic and dynamic properties of various segments of its body. Hence, the mass and center of mass/inertia data of the segments must be updated before simulating physics-based realistic motions. Most of the current methods use mass and inertia properties calculated from a set of regression equations based on average of some population.

The objective of this paper is to present our method of predicting and simulating visually realistic and dynamically consistent human stair-climbing motion. The digital human is modeled as a 55-degrees of freedom branched mechanical system with associated human anthropometry-based link lengths, mass moments of inertia, and centers of gravity. The joint angle profiles are determined using a B-spline-based parametric optimization technique subject to different physics-based, task-based, and environment-based constraints. The formulation offers the ability to study effects of the magnitude and location of external forces on the resulting joint angle profiles and joint torque profiles. Several virtual experiments are conducted using this optimization-based approach and results are presented.

A framework to validate the predicted motion of a computer human model (Santos) is presented in this work. The proposed validation framework is a task-based methodology. It depends on the comparison of selected motion determinants and joint angles that play major roles in the task, using qualitative and quantitative statistical techniques. In the present work, the validation of Santos walking will be presented. Fortunately, the determinants for normal walking are well defined in the literature and can be represented by (i) hip flexion/extension, (ii) knee flexion/extension, (iii) ankle plantar/dorsiflexion, (iv) pelvic tilt, (v) pelvic rotation, and (vi) lateral pelvic displacement. While Santos is an ongoing research project, the results have shown significant qualitative agreements between the walking determinants of Santos and the walking determinants of four normal subjects.

This paper presents a novel approach to determining the joint motion coupling relationship for the human shoulder complex. The human shoulder complex is the most sophisticated part in terms of degrees of freedom and motion. In the literature, different human shoulder biomechanical models have been developed for various purposes. Also, researchers have realized that there are constant movement relationships among the shoulder bones: the clavicle, scapula, and humerus. This is due to muscles and tendons that are involved in skeletal motions. These relationships, which are also called shoulder rhythm, entail joint motion coupling and joint limit coupling. However, the scope of this work is to determine the joint motion coupling relationship. This relationship is available in the literature, but it is an Euler-angle-based relationship. In the virtual human modeling environment, we cannot directly use this Euler-angle-based relationship.

The human shoulder plays an important role in human posture and motion, especially in scenarios in which humans need achieve tasks with external loads. The shoulder complex model is critical in digital human modeling and simulation because a fidelity model is the basis for realistic posture and motion predictions for digital humans. The complexity of the shoulder mechanism makes it difficult to model a shoulder complex realistically. Although many researchers have attempted to model the human shoulder complex, there has not been a survey of these models and their benefits and limitations. This paper attempts to review various biomechanical models proposed and summarize the pros and cons. It focuses mainly on the human modeling domain, although some of these models were originally from the robotics field. The models are divided into two major categories: open-loop chain models and closed-loop chain models.

We propose an algorithm of predicting dynamic biped motions of Santos™ human model. An alternative and efficient formulation of the Zero-Moment Point (ZMP) for dynamic balance and the approximated ground reaction forces/moments are derived from the resultant reaction loads, which includes the gravity, the externally applied loads, and the inertia. The optimization problem is formulated to address the redundancy of the human task, where the general biped and the task-specific constraints are imposed depending on the task requirements. The proposed method is fully predictive and generates physically feasible human-like motions from scratch without any input reference from motion capture or animation. The resulting generated motions demonstrate how a human reacts effectively to different external load conditions in performing a given task by showing realistic features of cause and effect.

A robust design procedure is applied to achieve improved vehicle handling performance as an integral part of simulation-based vehicle design. This paper presents a hybrid robust design method, the robust design process strategy (RDPS), which makes full use of the intense complementary action of characteristics between the Response Surface Methodology (RSM) and the Taguchi method, to get the robust design of the vehicle handling performance. The vehicle multi-body dynamic model is built in the platform that is constructed by the software of iSIGHT, ADAMS/CAR, and MATLAB. The design-of-experiment method of the Latin Hypercube (LHC) is used to obtain the approximate area values, and then the RDPS is utilized to achieve improved vehicle handling performance results. The validation is made by the Monte Carlo Simulation Technique (MCST) in terms of the effectiveness of the RDPS in solving robust design problems.

Active steering systems can help the driver to master critical driving situations. This paper presents a fuzzy logic control strategy on active steering vehicle based on a multi-body vehicle dynamic model. The multi-body vehicle dynamic model using ADAMS can accurately predict the dynamic performance of the vehicle. A new hybrid steering scheme including both active front steering (applying an additional front steering angle besides the driver input) and rear steering is presented to control both yaw velocity and sideslip angle. A set of fuzzy logic rules is designed for the active steering controller, and the fuzzy controller can adjust both sideslip angle and yaw velocity through the co-simulation between ADAMS and the Matlab fuzzy control unit with the optimized membership function. To ensure the design of high-quality fuzzy control rules, a rule optimization strategy is introduced.

A method to simulate digital human running using an optimization-based approach is presented. The digital human is considered as a mechanical system that includes link lengths, mass moments of inertia, joint torques, and external forces. The problem is formulated as an optimization problem to determine the joint angle profiles. The kinematics analysis of the model is carried out using the Denavit-Hartenberg method. The B-spline approximation is used for discretization of the joint angle profiles, and the recursive formulation is used for the dynamic equilibrium analysis. The equations of motion thus obtained are treated as equality constraints in the optimization process. With this formulation, a method for the integration of constrained equations of motion is not required. This is a unique feature of the present formulation and has advantages for the numerical solution process.

Our previous formulation for optimization-based dynamic motion simulation of a serial-link human upper body (from waist to right hand) is extended to predict the motion of a tree-structured human model that includes the torso, right arm, and left arm, with various applied external loads. The dynamics of tree-structured systems is formulated and implemented. The equations of motion for the tree structures must be derived carefully when dealing with the connection link. The optimum solution results show realistic dual-arm human motions and the required joint actuator torques. In the second part of this paper, a new method is introduced in which the constraint forces and moments at the joints are calculated along with the motion and muscle-induced actuator torques. A set of fictitious joints are modeled in addition to the real joints.

A framework to study the response of seated operators to whole-body vibration (WBV) is presented in this work. The framework consists of (i) a six-degree-of-freedom man-rated motion platform to play back ride files of typical heavy off-road machines; (ii) an optical motion capture system to collect 3D motion data of the operators and the surrounding environment (seat and platform); (iii) a computer skeletal model to embody the tested subjects in terms of their body dimensions, joint centers, and inertia properties; (iv) a marker placement protocol for seated positions that facilitates the process of collecting data of the lower thoracic and the lumbar regions of the spine regardless of the existence of the seatback; and (v) a computer human model to solve the inverse kinematics/dynamic problem for the joint profiles and joint torques. The proposed framework uses experimental data to answer critical questions regarding human response to WBV.

A methodology involving Design for Six Sigma (DFSS) and Multi-body dynamic simulation is employed to tune a body-on-frame vehicle, for improved ride (shake) performance. The design space is limited to four sets of symmetric body mounts for a vehicle. The stiffness and damping characteristics of the mounts are the control factors in the virtual experiment. Variation of these design parameters from the nominal settings, as well as axle size, tire and wheel combinations, tire pressure, shock damping, and vehicle speed constitute the noise factors. This approach proves to be an excellent predictor of the vehicle behavior, by which much insight as to influence of each parameter on vehicle performance is gained. Ultimately, specific recommendations for the control factor settings are provided. Subsequent hardware builds show excellent agreement with the analytical model and suggested tuning.

Reliability-based design optimization (RBDO), which includes design optimization in design space and inverse reliability analysis in standard normal space, has been recently developed under the assumption that all input variables are independent because it is difficult to construct a joint probability distribution function (PDF) of input variables with limited data such as the marginal PDF and covariance matrix. However, since in real applications, it is common that some of the input variables are correlated, the RBDO results might contain a significant error if the correlation between input variables for RBDO is not considered. In this paper, Rosenblatt and Nataf transformations, which are the most representative transformation methods and have been widely used in the reliability analysis, have been studied and compared in terms of applicability to RBDO with correlated input variables.

Since 1997, General Motors Body Manufacturing Engineering - Die Engineering Services (BME-DES) has been working jointly with our software vendor to develop and implement a parallel version of stamping simulation software for mass production analysis applications. The evolution of this technology and the insight gained through the implementation of DMP/MPP technology as well as performance benchmarks are discussed in this publication.